A new lead complex, [Pb(mq)2], (mq = 2-methyl-8-hydroxyquinoline) was prepared via an electrochemical route from the oxidation of lead metal in the presence of 2-methyl-8-hydroxyquinoline in a fast and facile process. The complex was fully characterized by means of NMR and IR spectra and elemental analysis. The nanostructure of the prepared compound was obtained by sonoelectrochemical process and studied by scanning electron microscopy, atomic force microscopy, X-ray powder diffraction, IR spectroscopy and elemental analysis. Thermal stability of single crystalline and nanosize samples of the prepared compound was studied by thermal gravimetric and differential thermal analysis. The photoluminescence properties of the prepared compounds, as single crystals and as nanorods, have been investigated. The results showed a good correlation between the size and the shape of the complex particles and emission wavelength. The prepared complex was doped in PVK:PBD blend as guest and its application in the fabrication of OLED was studied. The ratio of lead complex was modified and was equal to 8 (w/w %) in PVK:PBD (100:40). 相似文献
Pactamycin is a bacteria‐derived aminocyclitol antibiotic with a wide‐range of biological activity. Its chemical structure and potent biological activities have made it an interesting lead compound for drug discovery and development. Despite its unusual chemical structure, many aspects of its formation in nature remain elusive. Using a combination of genetic inactivation and metabolic analysis, we investigated the tailoring processes of pactamycin biosynthesis in Streptomyces pactum. The results provide insights into the sequence of events during the tailoring steps of pactamycin biosynthesis and explain the unusual production of various pactamycin analogues by S. pactum mutants. We also identified two new pactamycin analogues that have better selectivity indexes than pactamycin against malarial parasites. 相似文献
The relation between microstructural inhomogeneity and thermal conductivity of a rheocast component manufactured from two different aluminum alloys was investigated. The formation of two different primary α-Al particles was observed and related to multistage solidification process during slurry preparation and die cavity filling process. The microstructural inhomogeneity of the component was quantified as the fraction of α1-Al particles in the primary Al phase. A high fraction of coarse solute-lean α1-Al particles in the primary Al phase caused a higher thermal conductivity of the component in the near-to-gate region. A variation in thermal conductivity through the rheocast component of 10% was discovered. The effect of an inhomogeneous temperature-dependent thermal conductivity on the thermal performance of a large rheocast heatsink for electronics cooling in an operation environment was studied by means of simulation. Design guidelines were developed to account for the thermal performance of heatsinks with inhomogeneous thermal conductivity, as caused by the rheocasting process. Under the modeling assumptions, the simulation results showed over 2.5% improvement in heatsink thermal resistance when the higher conductivity near-to-gate region was located at the top of the heatsink. Assuming homogeneous thermo-physical properties in a rheocast heatsink may lead to greater than 3.5% error in the estimation of maximum thermal resistance of the heatsink. The variation in thermal conductivity within a large rheocast heatsink was found to be important for obtaining of a robust component design. 相似文献
Two green nanocomposites of Co3O4 decorated CTAB/bentonite (Co@CT/BE) and chitosan/bentonite (Co@CH/BE) were synthesized as enhanced and environmental photocatalysts and antibacterial agents. As photocatalysts, the products were applied in the effective oxidation of toxic methyl parathion pesticide (MP) in wastewater under a visible light source. The application of Co@CH/BE (0.02 g) resulted in the complete oxidation of MP (50 mg/L) after 40 min and complete mineralization after 60 min. while the complete oxidation and mineralization of MP (50 mg/L) by Co@CT/BE was recognized after 75 min and 100 min, respectively. The Co@CH/BE composite is of higher activity than Co@CT/BE and can cause complete oxidation for MP at high concentrations up to 100 mg/L after 75 min. The oxidation pathway was illustrated considering the existence of the hydroxyl radicals as the active oxidizing species and the identified secondary organic compounds during the oxidation tests. The detected intermediate converted into end products of CO2 and inorganic anions of SO4?2, NO3?, and PO4?3 at the final stages of the oxidation processes. As antibacterial agents, the two composites exhibit considerable inhabitation zones of about 20 mm against both the Gram-positive Staphylococcus aureus and Gram-negative bacterium Vibrio Sp. The synthetic Co@CH/BE showed the best antibacterial properties with 200 μg/mL as minimum inhibitory against Staphylococcus aureus.
This study aims to investigate how the predeposition machining processes such as magnetic grinding, turning machining, and wire electrical discharge machining can influence the surface properties including electrochemical and tribological behavior of TiCrN nanostructured coating applied on Mo40 steel substrate. A physical vapor deposition technique using cathodic arc evaporation was used to apply the coating. The crystallographic phases and the microstructure of the coating were studied by X-ray diffraction and scanning electron microscope, respectively. Rockwell-C, electrochemical impedance spectroscopy and potentiodynamic polarization, and pin-on-disk wear tests were employed to evaluate the adhesion strength, corrosion behavior, and tribological property of specimens, respectively. The electrochemical results after 24 h of exposure to 3.5 wt% NaCl solution showed that TiCrN coating pretreated with a turning process with polarization resistance of about 3525.32 Ω.cm2 had the best corrosion resistance among all specimens. This was because of the improvement of the smoothness, surface quality, and adhesion after the turning process. On the other, the friction coefficient of the grounded sample is less than that of other ones. This is probably due to its higher adhesion strength and higher surface smoothness. 相似文献
In this paper, the authors introduce an experimental procedure for predicting the fatigue life of each individual rolling element bearing separately using vibration modal analysis. The experimental procedure was developed based on a statistical analysis. A statistical analysis was performed to find an empirical model that correlates the dynamic load capacity of rolling bearings to their dynamic characteristics (Natural frequencies and damping). These dynamic characteristics are obtained from the frequency response function of each individual bearing that results from vibration modal analysis. A modified formula to the already known Lundberg-Palmgren life formula is proposed for rolling element bearings. Given the modified formula, one can predict the fatigue life of each individual rolling element bearing based on its dynamic characteristics. The paper compares the results from the modified formula with those from Lundberg-Palmgren formula. The modified formula provides an accurate prediction for the fatigue life of each individual bearing based on its dynamic characteristics. The experimental validation of the modified formula is considered for future work. Therefore, it can be used in various applications of rolling element bearings in machinery systems. 相似文献
Starch carbamate was prepared by reacting maize starch with urea using solid state technique. The different factors affecting this reaction were studied. These factors include urea concentration, type of starch, reaction and duration. The carbamate extent and carbamation reaction efficiency (%) were traced by estimating the nitrogen content of the reaction product. Solubility, viscosity and total ester content of starch carbamate samples were estimated. The carbamate extent increases by increasing urea concentration as well as reaction temperature and duration. Increasing the reaction temperature and duration has the same effect on carbamation reaction efficiency (%), while increasing urea concentration do the reverse. The solubility (%) of starch carbamate samples depends on urea concentration, reaction temperature and duration as well as the type of starch used. The maximum solubility obtained was 63% and 43% for starch carbamate derived from pregelled and native starch, respectively. Tentative mechanism for the reaction between starch and urea has been proposed. 相似文献
Volatile organic compounds (VOCs) are among the major sources of air pollution. Catalytic ozonation is an efficient process for removing VOCs at lower reaction temperature compared to catalytic oxidation. In this study, a series of alumina supported single and mixed manganese and cobalt oxides catalysts were used for ozonation of acetone at room temperature. The influence of augmenting the single Mn and Co catalysts were investigated on the performance and structure of the catalyst. The manganese and cobalt single and mixed oxides catalysts of the formula Mn10%-CoX and Co10%-MnX (where X= 0, 2.5%, 5%, or 10%) were prepared. It was found that addition of Mn and Co at lower loading levels (2.5% or 5%) to single metal oxide catalysts enhanced the catalytic activity. The mixed oxides catalysts of (Mn10%-Co2.5%) and (Mn10%-Co5%) led to acetone conversion of about 84%. It is concluded that lower oxidation state of the secondary metal improves ozone decomposition and oxidation of acetone. 相似文献