Noise–Power Optimization of Incremental Data Converters

Incremental data converters (IDCs) are useful in instrumentation and measurement applications, where low-frequency analog signals need to be converted into digital form with high accuracy and low power dissipation. They are particularly well suited for applications where a single analog-digital converter is multiplexed between many channels. This paper proposes an exact design methodology for IDCs, which optimizes the signal-to-noise ratio of the converter under practical design constraints. The process also allows the designer to apportion the noise budget in an arbitrary manner between thermal and quantization noise. The design process is illustrated by an example which describes the optimization of a third-order multiplexed IDC.     

Cost-Efficient SHA Hardware Accelerators

This paper presents a new set of techniques for hardware implementations of Secure Hash Algorithm (SHA) hash functions. These techniques consist mostly in operation rescheduling and hardware reutilization, therefore, significantly decreasing the critical path and required area. Throughputs from 1.3 Gbit/s to 1.8 Gbit/s were obtained for the SHA implementations on a Xilinx VIRTEX II Pro. Compared to commercial cores and previously published research, these figures correspond to an improvement in throughput/slice in the range of 29% to 59% for SHA-1 and 54% to 100% for SHA-2. Experimental results on hybrid hardware/software implementations of the SHA cores, have shown speedups up to 150 times for the proposed cores, compared to pure software implementations.      

Enhancing Chaotic Communication Performances by Manchester Coding

A numerical analysis of an optical chaotic transmission system, based on the synchronization of two chaotic lasers, in a master-slave closed loop configuration is presented. At the transmitter, the master chaotic wave is superposed on the information message; at the receiver, the message is recovered by subtracting the synchronized slave chaotic wave from the received signal. The performances are analyzed in terms of the Q-factor, considering two different message modulation formats: the nonreturn-to-zero and the Manchester coding. The Manchester coding shows enhanced performances due to the shift of the signal spectrum to higher frequencies.     

Effect of hot pressing on processing and properties of BBN ceramics

BBN (BaBi₂Nb₂O₉) is very interesting and promising lead free material with relaxor properties in capacitors, sensors and actuators.     

A time series bootstrap procedure for interpolation intervals

A sieve bootstrap procedure for constructing interpolation intervals for a general class of linear processes is proposed. This sieve bootstrap provides consistent estimators of the conditional distribution of the missing values, given the observed data. A Monte Carlo experiment is used to show the finite sample properties of the sieve bootstrap and finally, the performance of the proposed method is illustrated with a real data example.     

Mechanisms of rectification of a high-frequency signal by a field-effect heterotransistor with a short channel

The effect of nonlinearity of the drift velocity of free charge carriers and the gradient-and concentration-related nonlinearities in the power-voltage sensitivity of a field-effect transistor with a short channel are studied theoretically. Theoretical results are compared with experimental data on the detection of terahertz radiation. It follows from the comparison that, in order to gain deeper insight into observed systematic features in the analysis of high-frequency characteristics of the transistor, one has to take into account some other mechanisms of the current nonlinearity, in addition to the plasma-related nonlinearity.     

Investigation into Polarization of Unloaded and Loaded Microstrip Square-Ring Antennas

The polarization characteristic of unloaded and loaded square-ring microstrip antennas is investigated. Several different loading types like single-stub, dual-stub, notch, gap and shorting-pin are considered and their effects are studied. Loading enables feeding using a 50-Omega probe. The simulation and measurement results show that the loading techniques excite a loaded TMy ₁₁ mode that is orthogonal to the unloaded TMx ₁₁ mode. This indicates that by loading the ring antenna its polarization can be switched adaptively. However, the purity of the loaded and unloaded modes depends on the loading type. For some loading types like gap and shorting-pin, the excitation of the unloaded mode seems negligible, in comparison to the loadings by stub and notch. For the stub and notch loaded antennas the unloaded mode is also present, and its excitation efficiency is frequency dependent. Thus, their polarization plane, which is due to both loaded TMy ₁₁ and unloaded TMx ₁₁ modes, also becomes frequency dependant. The results of this investigation can be useful in selecting the loading methods for high-impedance microstrip ring antennas, and control of their impedance and polarization. The knowledge of the antenna polarization is essential in communications, and its dependence on the loading type can be used as an important parameter in design of adaptive antennas and sensors.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Sequential batch reactor for eucalypt kraft pulp effluent treatment with Trametes versicolor

BACKGROUND: A sequential batch reactor (SBR) was used for eucalypt kraft pulp effluent treatment with Trametes versicolor. A 2³ full factorial design and response surface methodology were applied to optimise the batch fermentation conditions. Effluent concentration, culture medium and inoculum age were the factors selected for this study in order to optimise the reduction of chemical oxygen demand (COD). RESULTS: The presence of Trametes Defined Medium (TDM) in the fermentation was required to obtain a significant COD reduction. Experiments in the batch reactor confirmed, in general, the predicted results of optimisation developed from Erlenmeyer batch assays. The T. versicolor culture remained active during 42 days of study in the SBR, providing approximately 80% of COD reduction. CONCLUSION: Trametes versicolor may be considered as very promising for the biological treatment of effluents from kraft pulp mills in an SBR system instead of the activated sludge mixed cultures traditionally used. Copyright © 2008 Society of Chemical Industry     

Complex processing of fluorine-containing wastes of fluorite ores

The possibility of processing fluorine-containing wastes of fluorite ore, which include fluorite, calcite, quartz, and anorthite, has been investigated. A manufacturing flow chart of the complex processing of the ore waste materials with the production of sodium fluoride, alumina, soda ash, and raw materials suitable for the production of Portland cement and wollastonite is suggested.