Shaping the Toroidal Section of End Mills

The shaping of the toroidal cutting section of end mills is considered. Methods are devised for selecting the positional parameters in shaping the helical rake surface on the toroidal section. Relations are established between the geometric parameters of the end mill in the toroidal section.     

PETROLEUM POTENTIAL, THERMAL MATURITY AND THE OIL WINDOW OF OIL SHALES AND COALS IN CENOZOIC RIFT BASINS, CENTRAL AND NORTHERN THAILAND

Oil shales and coals occur in Cenozoic rift basins in central and northern Thailand. Thermally immature outcrops of these rocks may constitute analogues for source rocks which have generated oil in several of these rift basins. A total of 56 oil shale and coal samples were collected from eight different basins and analysed in detail in this study. The samples were analysed for their content of total organic carbon (TOC) and elemental composition. Source rock quality was determined by Rock‐Eval pyrolysis. Reflected light microscopy was used to analyse the organic matter (maceral) composition of the rocks, and the thermal maturity was determined by vitrinite reflectance (VR) measurements. In addition to the 56 samples, VR measurements were carried out in three wells from two oil‐producing basins and VR gradients were constructed. Rock‐Eval screening data from one of the wells is also presented. The oil shales were deposited in freshwater (to brackish) lakes with a high preservation potential (TOC contents up to 44.18 wt%). They contain abundant lamalginite and principally algal‐derived fluorescing amorphous organic matter followed by liptodetrinite and telalginite (Botryococcus‐type). Huminite may be present in subordinate amounts. The coals are completely dominated by huminite and were formed in freshwater mires. VR values from 0.38 to 0.47%R_o show that the exposed coals are thermally immature. VR values from the associated oil shales are suppressed by 0.11 to 0.28%R_o. The oil shales have H/C ratios >1.43, and Hydrogen Index (HI) values are generally >400 mg HC/g TOC and may reach 704 mg HC/ gTOC. In general, the coals have H/C ratios between about 0.80 and 0.90, and the HI values vary considerably from approximately 50 to 300 mg HC/gTOC. The HI_max of the coals, which represent the true source rock potential, range from ～160 to 310 mg HC/g TOC indicating a potential for oil/gas and oil generation. The steep VR curves from the oil‐producing basins reflect high geothermal gradients of ～62°C/km and ～92°C/km. The depth to the top oil window for the oil shales at a VR of ～0.70%R_o is determined to be between ～1100 m and 1800 m depending on the geothermal gradient. The kerogen composition of the oil shales and the high geothermal gradients result in narrow oil windows, possibly spanning only ～300 to 400 m in the warmest basins. The effective oil window of the coals is estimated to start from ～0.82 to 0.98%R_o and burial depths of ～1300 to 1400 m (～92°C/km) and ～2100 to 2300 m (～62°C/km) are necessary for efficient oil expulsion to occur.     

Theoretical and practical implications of creep curve shape analyses for 7010 and 7075

Over tensile stress ranges giving creep lives up to 2000 hours at 373 to 463 K, the creep and creep fracture properties of 7010 are compared with results recorded for 7075 and other precipitation-hardened aluminum alloys. Using the ϕ methodology to quantify the systematic variations in creep curve shape with changing test conditions, the behavior patterns displayed by the different alloys are shown to depend on the extent to which precipitate coarsening causes a progressive loss of creep strength with increasing test duration and temperature. The ϕ relationships also introduce new approaches for rationalization and interpretation of creep data sets, based on the activation energy for lattice diffusion in the alloy matrices and the yield stress or UTS at the creep temperatures.     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Atomistic simulations of grain boundary migration in copper

While the motion of twist boundaries can be readily studied by atomistic simulations with molecular dynamics (MD) under the action of an elastic driving force, the approach fails for tilt boundaries. This is due to the interaction of the elastic stress with the grain boundary (GB) structure, which causes plastic strain by GB sliding. A novel concept, the orientation correlated driving force, is introduced to circumvent this problem. It is shown that this concept can be successfully applied to the study of the migration of tilt boundaries. The migration behavior of several twist and tilt GBs was investigated. The transition from low-to high-angle boundaries can be captured, and a structural transition of tilt boundaries was found at high temperatures, which also affected the migration behavior. The results compare well with experimental results of the motion high-angle boundaries, but for low-angle boundaries, the agreement is poor. This article is based on a presentation made in the “Hillert Symposium on Thermodynamics & Kinetics of Migrating Interfaces in Steels and Other Complex Alloys,” December 2–3, 2004, organized by The Royal Institute of Technology in Stockholm, Sweden.     

On-line estimation of kinetic parameters in anaerobic digestion using observer-based estimators and multiwavelength fluorometry.

Observer-based estimators (OBE) were used for estimation of state variables and kinetic parameters in an anaerobic digestion (AD) process. A simplified first-order model with time-varying kinetic parameters was used to design an OBE for kinetic parameter estimation. This approach was validated on a laboratory-scale anaerobic reactor equipped with a multiwavelength fluorometer for on-line measurements of COD and VFA concentrations in the reactor effluent. The proposed estimators provide continuous adjustment of kinetic parameters and can be used for predictions of state variables between samples acquisition and during sensor failure.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Sensor guided handling and assembly of active micro-systems

Positioning accuracies in the range of a few micrometers and below are necessary for the assembly of active micro-systems. In order to reach these accuracies, an assembly system for sensor guided micro-assembly is developed in the Collaborative Research Centre 516 “Design and manufacturing of active micro-systems”. The combination of a parallel robot with an integrated 3D vision sensor and a micro-gripper enables to reach relative positioning accuracies below 1 μm.     

E. H. Dirksens Beiträge zu den Grundlagen der Analysis

Enno Heeren Dirksen (1788–1850) was one of several mathematicians originating from Eastern Frisia at the end of the eighteenth century to acquire prominence in neohumanist reformed Prussia. While striving—like so many of his contemporaries—for more rigour in the foundations of calculus, his work is significant due to his unusual emphasis on the semiotic aspects of the basic concepts. As a clear-sighted propagator of Cauchy's conceptual innovations in Germany, his achievements in improving sign expressions of such concepts enabled him to clarify hitherto not differentiated multiple limit processes—although less successfully in constructive concept formation itself. The contribution is based on the analysis of Dirksen's published texts and on the numerous texts which remained drafts for his projected voluminousOrganon der gesamten Analysis.

---

---

Menso Folkerts zum 60. Geburtstag gewidmet