Organotin compounds in the liver tissue of marine mammals from the Polish coast of the Baltic Sea

Butyltins (BTs) and phenyltins (PhTs) were determined in the livers of marine mammals found by-caught or stranded along the Polish coast of the Baltic Sea. During the investigation an original analytical method was developed. Butyltin compounds were detected in all the liver samples, whereas phenyltins were not detected in any of the samples. The total concentrations of BTs ranged from 43.9 to 7698 ng(Sn) x g(-1) dry weight. Age-related trends to accumulate BTs in immature porpoises were found. At the same time there were no male-female differences in BTs concentrations observed. No statistically significant spatial distribution differences were found between the locations corresponding to the open Baltic Sea waters and inside the Gulf of Gdańsk, which is characterized by high maritime activity. In comparison to butyltin levels in marine mammals from other geographic regions, the samples analyzed indicate a significant degree of tributyltin pollution along the Polish coast of the Baltic Sea. On the basis of a literature review, higher BT levels are usually found in waters close to highly industrialized areas, such as Japan, Hong Kong, and the United States.     

Identification of the impedance model of an implanted cochlear prosthesis from intracochlear potential measurements

Those suffering from a severe to profound sensorineural hearing loss can obtain substantial benefit from a cochlear implant prosthesis. An electrode array implanted in the inner ear stimulates auditory nerve fibers by direct injection of electrical current. A major limitation of today's technology is the imprecise control of intracochlear current flow, particularly the relatively wide spread of neural excitation. A better understanding of the intracochlear electrical fields is, therefore, required. This paper analyzes the structure of intracochlear potential measurements in relation to both the subject's anatomy and to the properties of the electrode array. An electrically equivalent network is proposed, composed of small lumped circuits for the interface impedance and for the cochlear tissues. The numerical methods required to estimate the model parameters from high-quality electrical potential recordings are developed. Finally, some models are presented for subjects wearing a Clarion CII device with a HiFocus electrode and discussed in terms of model reliability.     

Factors affecting the potentiometric response of all-solid-state solvent polymeric membrane calcium-selective electrode for low-level measurements

An all-solid-state calcium-selective electrode was constructed with poly(pyrrole) solid-contact doped with calcium complexing ligand Tiron. The potentiometric response of this sensor can have a linear range down to 10(-)(9) M with a slope close to Nernstian and detection limit equal to 10(-)(9.6). The effects of pH and the activity of the interfering ion in the conditioning solution on the potentiometric behavior of the constructed sensors were examined. Potential stability, reproducibility, and impedance studies were performed. The selectivity of the constructed electrode is better than that of the conventional calcium-selective electrode with internal filling solution of 10(-)(2) M CaCl(2) and comparable to that of the best liquid-contact electrodes.     

Limitations of the potential step technique to impedance measurements using discrete time Fourier transform

Recently, a new method of measuring impedance of electrochemical systems was proposed in the literature by Yoo and Park (Yoo, J.-S.; Park, S.-M. Anal. Chem. 2000, 72, 2035). It is based on the analysis of system response to a potential step. Differentiation of the applied potential step and the current response in the time domain followed by applying Fourier transform to both signals allows for determination of the system's impedance. It has been proposed that the measurements carried out in a short time period permit the determination of the system's impedance in the whole frequency range. The aim of the present work was to verify the validity of the impedance spectra obtained using this method, as well as to establish the conditions for which the method may be used. This method was tested using simulated data for a simple ideally polarized electrode and a simple one-electron redox system in the solution. The results show that the reliable impedance spectra may be obtained only for frequencies between 1/(NDeltat) and 1/(2Deltat), where Deltat denotes the sampling time and N is the number of points acquired during the experiment. However, the artifacts are generated when the experimental data are extrapolated to lower frequencies.     

Generation of Inequivalent Generalized Bell Bases

The notion of equivalence of maximally entangled bases of bipartite d–dimensional Hilbert spaces _{d d} is introduced. An explicit method of inequivalent bases construction is presented. PACS: 03.67.-a     

Kinetic modeling of the laser-induced breakdown spectroscopy plume from metallic lead

We report initial results of a study aimed toward developing a computational fluid dynamics (CFD) model to simulate the laser-induced breakdown spectroscopy (LIBS) plume for the purpose of understanding the physical and chemical factors that control the LIBS signature. The kinetic model developed for modeling studies of the LIBS plume from metallic lead includes a set of air reactions and ion chemistry as well as the oxidization, excitation, and ionization of lead atoms. At total of 38 chemical species and 220 reactions are included in the model. Experimental measurements of the spatial and temporal dependence of a number of lead emission lines have been made of the LIBS plume from metallic lead. The mechanism of generation of excited Pb states in the LIBS plume is analyzed through kinetic modeling and sensitivity analysis. Initial CFD model results for the LIBS plume are presented.     

Laser-induced breakdown spectroscopy of bacterial spores, molds, pollens, and protein: initial studies of discrimination potential

Laser-induced breakdown spectroscopy (LIBS) has been used to study bacterial spores, molds, pollens, and proteins. Biosamples were prepared and deposited onto porous silver substrates. LIBS data from the individual laser shots were analyzed by principal-components analysis and were found to contain adequate information to afford discrimination among the different biomaterials. Additional discrimination within the three bacilli studied appears feasible.     

Laser-induced breakdown spectroscopy analysis of energetic materials

A number of energetic materials and explosives have been studied by laser-induced breakdown spectroscopy (LIBS). They include black powder, neat explosives such as TNT, PETN, HMX, and RDX (in various forms), propellants such as M43 and JA2, and military explosives such as C4 and LX-14. Each of these materials gives a unique spectrum, and generally the spectra are reproducible shot to shot. We observed that the laser-produced microplasma did not initiate any of the energetic materials studied. Extensive studies of black powder and its ingredients by use of a reference spectral library have demonstrated excellent accuracy for unknown identification. Finally, we observed that these nitrogen- and oxygen-rich materials yield LIBS spectra in air that have correspondingly different O:N peak ratios compared with air. This difference can help in the detection and identification of such energetic materials.     

On Some Nonlinear Measures of Diabetic Autonomic Dysfunction

Beat-to-beat heart rate was measured for 50 normal and 60 diabetic subjects. Autonomic dysfunction in diabetic subject was assessed by the Ewing test. Next we employed two nonlinear measures of cardiac interbeat interval dynamics: entropy-like measure on AIP diagram, and parameter "forbidden words" for symbolic dynamics. We test their performance in detecting diabetic autonomic dysfunction and show that there is a very significant relationship between the measures and the Ewing score.     

Simulation of stochastic metal-forming process for rigid-viscoplastic material

Numerical solution of stochastic metal-forming process is analysed. The theoretical formulation is described which presents probabilistic distributions for velocities and strains taking into account random initial and boundary conditions. Finite element equations for rigid-viscoplastic materials are solved for the first two probabilistic moments of the random velocity field. The example of ring compression with random parameters is presented.