Nile blue adsorbed onto silica gel modified with niobium oxide for electrocatalytic oxidation of NADH

A study of modified carbon paste electrode employing Nile blue (NB) adsorbed on silica gel modified with niobium oxide (SN) for electrocatalytic oxidation of reduced nicotinamide adenine dinucleotide (NADH) is described. The adsorbed organic dye on SN was used to prepare a modified carbon paste electrode to investigate its electrochemical properties. The formal potential (E°′) of the adsorbed NB (−230 mV vs. saturated calomel electrode, SCE) showed a shift of 70 mV towards a more positive potential value, compared to NB dissolved in aqueous solution. In solutions with pH between 6.0 and 8.0 did stability and E°′ remained almost constant. However, for a solution pH lower than 6.0 the E°′ was affected by the acidity of the contacting solution, shifting the E°′ towards more positive values. For the solution pHs between 6.0 and 8.0 the electrocatalytic activity remained almost constant. A linear response range for NADH between 1.0×10⁻⁵ and 5.2×10⁻⁴ mol l⁻¹, at pH 7.0, was observed for the electrode, with an applied potential of −200 mV versus SCE. The formation of an intermediate charge transfer (CT) complex was proposed to the CT reaction between NADH and adsorbed NB. The heterogeneous electron transfer rate, k_obs, was 1400 M⁻¹ s⁻¹ and the apparent Michaelis-Menten constant, was 0.21 mM at pH 7.0 evaluated from rotating disk electrode (RDE) experiments with an electrode coverage of about 5.2×10⁻⁹ mol cm⁻². The increase in the reaction rate between NADH and the immobilized NB compared to those obtained with dissolved NB was assigned to the shift of the E°′ towards more positive values.     

Blends of polyamide 6 with bisphenol-A polycarbonate. I. Thermal properties and compatibility aspects

Blends of polyamide 6 (PA6) and polycarbonate (PC) have been investigated, over a full range of composition, to check interactions between them. SEM observations show that the mixtures are characterized by domains of clearly segregated homophases and voids between the two polymers. DSC and DMTA data indicate the presence of two T_g' s, corresponding to two separate phases, with the T_g of the PC phase decreasing on increasing the PA6 amount. Moreover, the crystallization kinetics of PA6 is slightly showed down by the PC. Chemical reactions between the two polymers are supposed to give rise to low molar mass compounds, as shown by GPC; these species plasticize the PC and partially dissolve into the molten polyamide, causing decrease of PC T_g and reduction of overall crystallization rate of PA6. Apparent influence of PC on melting temperature and enthalpy of PA6 is also discussed.     

Effects of physical refining on contents of waxes and fatty alcohols of refined olive oil

Changes in the contents of waxes and fatty alcohols during deodorization/physical refining of bleached olive oil were studied. Experiments were carried out with 1.85% acidity oil, which was physically refined in a discontinuous deodorizer of 250-kg maximum capacity using nitrogen as stripping gas instead of steam. The variables studied were load and temperature of oil in the deodorizer as well as N₂ flow. Analyses of waxes and alcohols were carried out at different operation times. The maximum content of wax was always observed when the oil reached the deodorization temperature. The variation in the wax content depended on temperature and N₂ flow. Wax decomposition started and continued during the operating time, and a progressive decrease, which was pronounced between 3 and 4 h, was observed. Small changes in waxes were observed between 4 and 5 h. Total content of fatty alcohols diminished throughout the operating time, and changes did not depend on the variables studied.     

Comparative analysis of methods for determining the metabolic rate in order to provide a balance between man and the environment

The incorrect determination of metabolic rate can be linked to discrepancies between the model of the PMV (Predicted Mean Vote) and real thermal sensation collected in field studies. Aiming to improve the correlation of the PMV model and the real thermal sensation, this work established new values for the metabolic rate: one way being called “calculated” using Newton's Method and the other called "measured" using a metabolic analyzer. Welder's activities were evaluated, through the measurements of environmental and personal variables. New values of metabolic rate were determined for this activity. The values found for the calculated form and the measured one were, respectively, 178.63 and 145.46 W/m², different from the range provided by the table of ISO 8996 (2004) for this activity (75–125 W/m²). In order to verify which of the values of the metabolic rate was closer to the real thermal sensation of PMV, a linear regression was made between the PMV and the real thermal sensation in three ways: S × PMV_tabulated (R² = 0.1749), S × PMV_calculated (R ² = 0.7481) and S × PMV_measured (R² = 0.7854). It was found that the values measured by the instrument gave a higher coefficient of determination which was chosen for the correction of the table. The correction of the table provides a value of M_predicted, that is a value of metabolic rate that corrects the values provided by the tables of ISO 8996 (2004), by means of a correction coefficient. For the welder's activities in a metal-mechanics industry, tabulated values can be multiplied by the correction coefficient 1.4648 in order to minimize inaccuracies. The PMV_predicted, obtained through the M_predicted, when related to the actual thermal sensation, provides a coefficient of determination of 0.7511, thereby improving the model of the PMV.     

Interactional Order and Constructed Ways of Seeing with Touchless Imaging Systems in Surgery

While surgical practices are increasingly reliant on a range of digital imaging technologies, the ability for clinicians to interact and manipulate these digital representations in the operating theatre using traditional touch based interaction devices is constrained by the need to maintain sterility. To overcome these concerns with sterility, a number of researchers are have been developing ways of enabling interaction in the operating theatre using touchless interaction techniques such as gesture and voice to allow clinicians control of the systems. While there have been important technical strides in the area, there has been little in the way of understanding the use of these touchless systems in practice. With this in mind we present a touchless system developed for use during vascular surgery. We deployed the system in the endovascular suite of a large hospital for use in the context of real procedures. We present findings from a study of the system in use focusing on how, with touchless interaction, the visual resources were embedded and made meaningful in the collaborative practices of surgery. In particular we discuss the importance of direct and dynamic control of the images by the clinicians in the context of talk and in the context of other artefact use as well as the work performed by members of the clinical team to make themselves sensable by the system. We discuss the broader implications of these findings for how we think about the design, evaluation and use of these systems.     

Autocalibration with the Minimum Number of Cameras with Known Pixel Shape

In 3D reconstruction, the recovery of the calibration parameters of the cameras is paramount since it provides metric information about the observed scene, e.g., measures of angles and ratios of distances. Autocalibration enables the estimation of the camera parameters without using a calibration device, but by enforcing simple constraints on the camera parameters. In the absence of information about the internal camera parameters such as the focal length and the principal point, the knowledge of the camera pixel shape is usually the only available constraint. Given a projective reconstruction of a rigid scene, we address the problem of the autocalibration of a minimal set of cameras with known pixel shape and otherwise arbitrarily varying intrinsic and extrinsic parameters. We propose an algorithm that only requires 5 cameras (the theoretical minimum), thus halving the number of cameras required by previous algorithms based on the same constraint. To this purpose, we introduce as our basic geometric tool the six-line conic variety (SLCV), consisting in the set of planes intersecting six given lines of 3D space in points of a conic. We show that the set of solutions of the Euclidean upgrading problem for three cameras with known pixel shape can be parameterized in a computationally efficient way. This parameterization is then used to solve autocalibration from five or more cameras, reducing the three-dimensional search space to a two-dimensional one. We provide experiments with real images showing the good performance of the technique.     

Effect of low‐temperature plasma and chitosan treatment on wool dyeing with Acid Red 27

This study examines in detail the influence of low‐temperature plasma and biopolymer chitosan treatments on wool dyeability. Wool knitted fabrics were treated and characterized by whiteness and shrink‐resistance measurements. Surface modification was assessed by contact‐angle measurements of human hair fibers, which were used as a model to study the wetting properties of the treated wool knitted fabrics. The dyeing behavior was assessed from the diffusion mechanism point of view. The dyeing kinetics were measured at two different pHs (4.2 and 6.5) and three different temperatures (60, 85, and 100°C) to gain information about the contribution of the surface modification treatment to the dyeing mechanism. The exhaustion and reflectance data were compared, and the apparent diffusion coefficients were calculated. On the basis of the obtained results, a model for the dyeing mechanism of the chitosan treated wool was proposed. When treated with chitosan, the polymer sheath spread on the surface of the fibers acted as a predominant dyeing site in very short dyeing times, thus interacting with the dye and in later stages imparting the dye to the wool fiber. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2204–2214, 2005     

Straightforward modeling of dynamic I–V characteristics for microwave FETs

This work presents a straightforward approach aimed at modeling the dynamic I–V characteristics of microwave active solid‐state devices. The drain‐source current generator represents the most significant source of nonlinearity in a transistor and, therefore, its correct modeling is fundamental to predict accurately the current and voltage waveforms under large‐signal operation. The proposed approach relies on using a small set of low‐frequency time‐domain waveform measurements combined with numerical optimization‐based estimation of the nonlinear model parameters. The procedure is applied to a gallium nitride HEMT and silicon FinFET. The effectiveness of the modeling procedure in terms of prediction accuracy and generalization capability is demonstrated by validation of the extracted models under operating conditions different than the ones used for the parameters estimation. Good agreement between measurements and model simulations is achieved for both technologies and in both low‐ and high‐frequency range. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:109–116, 2014.     

Smoothing: A natural way to detect contour features

This work presents a dominant point detector. The angles of the contour are characterized through local entropy produced by a rotationally symmetric smoothing. The proposed scheme uses a punctual multi-scale approach in which only the candidates are analyzed in higher scales. To preserve the angle-entropy relationship in higher scales, we propose a smoothing kernel which presents special features that ensure its steepness in every scale. It is built from the sum of two Gaussians with different openings resembling center-surround receptive fields. The outputs of the proposed method are confronted to a ground-truth found in the literature, and to popular boundary based corner detectors that used the same set of images. Results reveal that the proposed detector performs extremely well.     

Binary and m-ary encoding in applications of tree-based genetic algorithms for QoS routing

Ubiquitous and Pervasive Computing (UPC) applications often have Quality of Service (QoS) requirements. These become constraints for the UPC network infrastructure. In this paper, we refer to Mobile ad Hoc Networks, one of the most important technologies supporting UPC, and investigate on Genetic Algorithms (GAs) for QoS routing. GAs are part of the soft computing paradigm and can solve the NP search of QoS routes with multiple constraints. We elaborate on tree-based GAs, which represent the set of paths from source to destination as a tree and encode them through the crossed junctions. While their most well-known applications use m-ary encoding representing single paths in the chromosomes, in this paper we discuss a binary encoding with the objective of improving the convergence speed. The binary encoding represents classes of paths in the chromosomes and allows local search on classes of paths. These classes are both collectively exhaustive and mutually exclusive. Simulation results compare convergence speed and scalability of GA applications with binary and m-ary encoding in networks with an increasing number of nodes and links per node. As the per-class processing is reason of additional computational cost, an hybrid GA application that uses both binary and m-ary encoding is introduced.