Enhanced Phase Stability and Photoluminescence of Eu3+ Modified t-ZrO2 Nanoparticles

Tetragonal ( t ) ZrO₂ nanoparticles have been obtained by a partial Eu³⁺→Zr⁴⁺ substitution, synthesized using a simple oxalate method at a moderate temperature of 650°C in air. The Eu³⁺ additive, 2 mol% used according to the optimal photoluminescence (PL), gives small crystallites of the sample. On raising the temperature further, the average crystallite size D grows slowly from 16 nm to a value as big as 49 nm at 1200°C. The Eu³⁺: t -ZrO₂ nanoparticles have a wide PL spectrum at room temperature in the visible to near-IR regions (550–730 nm) in the ⁵D₀→⁷F_J (Eu³⁺), J =1–4, electronic transitions. The intensity of the ⁵D₀→⁷F₄ group is as large as that of the characteristic ⁵D₀→⁷F₂ group of the spectrum in the forced electric-dipole allowed transitions. The enhanced t -ZrO₂ phase stability and wide PL can be attributed to the combined effects of an amorphous Eu³⁺-rich surface and part of the Eu³⁺ doping of ZrO₂ of small crystallites.     

Microstructure and water vapor transport properties of functionalized carbon nanotube‐reinforced dense‐segmented polyurethane composite membranes

This work investigates the influence of functionalized multiwall carbon nanotube (MWNT) on microstructure and water vapor transport properties of segmented polyurethane (SPU) membranes. SPUs were reinforced with four different concentration of MWNT viz. 0.25, 0.50, 1.0, and 2.5 wt%. Presence of the microcrystals in all SPU‐MWNT composite membranes was detected by wide angle X‐ray diffraction (WAXD). The percent crystallinity of SPU‐MWNT at 0.25 wt% content of MWNT was increased slightly when compared with the pristine SPU sample. However, further increase of MWNT decreases the order structure. Glass transition temperature was increases with increasing MWNT content in the SPUs, which signifies that MWNT could also affect the amorphous region of SPU. WAXD and transmission electron microscopy (TEM) results evidenced the interaction between SPUs and MWNT. In comparing the water vapor transport properties of MWNT‐SPU composite membranes, it was observed that at 0.25 wt% of MWNT in SPU, water vapor transport property increases slightly at soft segment crystal melting temperature. Further increase of MWNT content has no significant influence on the water vapor transport properties. However, at 2.5 wt% of MWNT in SPU matrix, water vapor transport was decreases due to the increase of stiffness in the polymer chains. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Characterization of friction stir welded joint of low nickel austenitic stainless steel and modified ferritic stainless steel

Friction stir welding (FSW) of dissimilar stainless steels, low nickel austenitic stainless steel and 409M ferritic stainless steel, is experimentally investigated. Process responses during FSW and the microstructures of the resultant dissimilar joints are evaluated. Material flow in the stir zone is investigated in detail by elemental mapping. Elemental mapping of the dissimilar joints clearly indicates that the material flow pattern during FSW depends on the process parameter combination. Dynamic recrystallization and recovery are also observed in the dissimilar joints. Among the two different stainless steels selected in the present study, the ferritic stainless steels shows more severe dynamic recrystallization, resulting in a very fine microstructure, probably due to the higher stacking fault energy.     

Effect of microstructure and chemical composition of hardfacing alloy on abrasive wear behavior

Hardfacing, a surface modification technique, is used to rebuild the surface of a workpiece. The economic success of the process depends on selective application of hardfacing material and its chemical composition for a particular application. In this context, three hardfacing electrodes having different chemical compositions have been selected and their abrasive wear responses was compared with that of mild steel. The emphasis has been made to realize the effect of microstructure and chemical composition on the wear response of the hardfacing material with respect to mild steel. It has been observed that the wear rate of hardfacing alloys is lower than that of mild steel. The hardfacing alloy having the highest chromium content exhibits the lowest wear rate.     

Effect of Dynamic Change in Strain Rate on Mechanical and Stress Corrosion Cracking Behavior of a Mild Steel

The current work analyzes the effect of the dynamic change in strain rate during tensile loading of a mild steel on its mechanical and stress corrosion behavior in 3.5 wt.% NaCl solution. The sample experiences high strain rate (10^?2 s^?1) up to 10, 15 and 20% of total deformation and then very low strain rate of 10^?6 s^?1 till fracture without any unloading in between. The behavioral characteristics of the steel under these circumstances are found to be different from that exhibited during complete loading till fracture both at high and slow strain rates separately. Total strain increases with the increase in the strain at which change in strain rate happens, and this is attributed to the generation of large number of dislocations at higher strain rate and subsequently release of dislocation at low strain rate during change over due to more time available for dynamic recovery. This observation is common for both in air and corrosive environment. One unique observation in this study is the higher total strain and lower strength observed during dynamic change in strain rate in the corrosive environment compared to that in air, which is attributed to the hydrogen-induced plasticity mechanism.     

Ru(II)–CO complexes of thioarylazoimidazoles: Syntheses,structures, spectroscopy and DFT calculation

The complexes, cis-(CO)-trans-(Cl)-[Ru(SRaaiNR)(CO)₂Cl₂] (2) and trans-(Cl)-[Ru(SRaaiNR)(CO)Cl₂] (3) (SRaaiNR = 1-alkyl-2-{(o-thioalkyl)phenylazo}imidazoles; R = Me (1a) and Et (1b)) have been synthesized and characterized. The structural confirmation is achieved by single crystal X-ray structure determinations. The complexes show Ru(III)/Ru(II) couple and ligand reductions. Electronic structure and spectral properties of the complexes have been explained with the DFT and TDDFT calculation.     

Studies on Hg(II) ion retention properties of cross-linked graft copolymer of acrylic acid and its analytical application

The effects of different parameters such as time, concentration, pH and temperature, on metal ion retention properties of the polymer have been investigated. Metal ion adsorption kinetics, isotherms and thermodynamics have been studied. A plausible mechanism for mercury ion retention has been suggested. Mercuric ion has been isolated quantitatively from various synthetic mixture containing metal ions (Ni²⁺, Cd²⁺, Pb²⁺ and Zn²⁺).     

Risk-Based Evaluation for Meeting Future Water Demand of the Brahmaputra Floodplain Within Bangladesh

A risk-based evaluation is performed for meeting future water demands in the Brahmaputra Floodplain Area within Bangladesh (BFA). This evaluation is carried out using three risk-based performance indicators: reliability, resiliency and vulnerability. The vulnerability indicator has been redefined incorporating the aspect of a supply failure. The analysis includes the impacts of climate change on both water demands and resources, and the generation of synthetic flows of the Brahmaputra River using time series models. The simulated values of the indicators reveal that the expected demand of the BFA up to the year 2050 can be supplied with the proposed Brahmaputra Barrage inside Bangladesh under the ‘no change’ in climatic condition, provided that the groundwater remains usable. However, if groundwater becomes unusable due to widespread arsenic contamination and/or a climate change occurs, it would not be possible to meet the future water demand of the region with high reliability, moderate resiliency and low vulnerability.     

Potential and viability of grid-connected solar PV system in Bangladesh

The potential of grid-connected solar PV system in Bangladesh was estimated utilizing GeoSpatial toolkit, NASA SSE solar radiation data and HOMER optimization software. Financial viability of solar photovoltaic as an electricity generation source for Bangladesh was also assessed utilizing a proposed 1-MW grid-connected solar PV system using RETScreen simulation software for 14 widespread locations in Bangladesh. The technical potential of gird-connected solar PV in Bangladesh was calculated as about 50174 MW. The annual electricity generation of the proposed system varied depending on the location between 1653 MWh and 1854 MWh, with a mean value of 1729 MWh. Several different economic and financial indicators were calculated, such as the internal rate of return, net present value, benefit-cost ratio, cost of energy production and simple payback. All indicators – for all sites – showed favorable condition for development of the proposed solar PV system in Bangladesh. The results also showed that a minimum of 1423 tons of greenhouse gas emissions can be avoided annually utilizing the proposed system at any part of the country.     

Analysis of a Localized Fire in a 3-D Tunnel Using a Hybrid Solver: Lattice Boltzmann Method,Finite-Volume Method,and Fully Explicit Upwind Scheme

A localized fire in a 3-D tunnel is analyzed by solving a combined-mode natural-convection and radiation problem. Nonlocal thermal equilibrium between air and smoke is considered. Separate energy equations are used for the two species. The density and temperature fields required for the solution of the energy equation are computed using the lattice Boltzmann method. The finite-volume method is used to compute radiative information. The energy equations are solved using the fully explicit upwind scheme. The Boussinesq approximation is used to account for the buoyancy effect. Effects of the scattering albedo, the convection-radiation parameter, and the wall emissivities on temperature profiles in the tunnel have been studied.