Creep performance of CNT reinforced glass fiber/epoxy composites: Roles of temperature and stress

Carbon nanotubes (CNTs) have been emerged as a potential nanofiller to reinforce polymeric materials to improve their mechanical properties, like strength and modulus. However, time-dependent deformation of such materials under a constant load and elevated temperature is a matter of concern for long-term durability of these materials. The present article primarily demonstrates the effects of creep temperature and stress on the reinforcement efficiency of CNT in a glass fiber/epoxy (GE) composite. Two types of materials were investigated in this study—GE which was used as a control material, as well as CNT embedded GE composite. To elucidate the impact of CNT on the long-term durability of GE composite, creep tests have been performed at different temperatures (50, 80, and 110 °C) under bending loading. As applied stress has also significant contribution toward the elevated creep deformation of materials, creep tests have also been carried out under different stresses (5, 10, and 40 MPa). The strength of the CNT-GE composite exhibited 8.7 and 18.3% higher than that of control GE composite under tensile and bending load, respectively. Results suggest CNT reinforcement to be beneficial for low temperature applications, both in terms of creep strain and strain rate. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47674.     

Electrospun microporous gelatin–polycaprolactone blend tubular scaffold as a potential vascular biomaterial

The work reported involved the fabrication of an electrospun tubular conduit of a gelatin and polycaprolactone (PCL) blend as an adventitia‐equivalent construct. Gelatin was included as the matrix for increased biocompatibility with the addition of PCL for durability. This is contrary to most of the literature available for biomaterials based on blends of gelatin and PCL where PCL is the major matrix. The work includes the assiduous selection of key electrospinning parameters to obtain smooth bead‐free fibres with a narrow distribution of pore size and fibre diameter. Few reports elucidate the optimization of all electrospinning parameters to fabricate tubular conduits with a focus on obtaining homogeneous pores and fibres. This stepwise investigation would be unique for the fabrication of gelatin–PCL electrospun tubular constructs. The fabricated microfibrous gelatin–PCL constructs had pores of size ca 50–100 μm reportedly conducive for cell infiltration. The measured value of surface roughness of 57.99 ± 17.4 nm is reported to be favourable for protein adhesion and cell adhesion. The elastic modulus was observed to be similar to that of the tunica adventitia of the native artery. Preliminary in vitro and in vivo biocompatibility tests suggest safe applicability as a biomaterial. Minimal cytotoxicity was observed using MTT assay. Subcutaneous implantation of the scaffold demonstrated acute inflammation which decreased by day 15. The findings of this study could enable the fabrication of smooth bead‐free microfibrous gelatin–PCL tubular construct as viable biomaterial which can be included in a bilayer or a trilayer scaffold for vascular tissue engineering. © 2019 Society of Chemical Industry     

Polyacrylate-coated graphene-oxide and graphene solution via chemical route for various biological application

In this work, we have developed a polyacrylate-coated graphene-oxide and then chemically reduced them into graphene. We found that polyacrylate coating can improve the colloidal stability of both graphene-oxide/graphene. They show good colloidal stability in different aqueous buffer solution with pH ranging from 5 to 10, and these solutions are stable for more than a month. The polyacrylate-coated grapheme oxide/graphene has been characterized by X-ray photoemission spectroscopy (XPS) and micro-Raman spectroscopy. Based on good colloidal stability, this graphene-oxide/graphene is most suitable for the biological application.     

Catalytic reaction in a circulating fluidized bed downer: Ozone decomposition

Catalytic ozone decomposition reaction was used to study the performance of a 76 mm i.d. and 5.8 m high gas–solid circulating fluidized bed (CFB) downer reactor. Optical fiber probes and an ultraviolet (UV) ozone analyzer were used to obtain comprehensive information about local solids holdup and ozone concentration profiles at different axial and radial positions at superficial gas velocity of 2–5 m/s and solids circulation rates of 50 and 100 kg/m² s. Axial ozone concentration profiles significantly deviated from the plug-flow behavior, with most conversion occurring in the entrance region or flow developing zone of the downer reactor. Strong correlation was observed between the spatial distributions of solids and extent of reaction; higher local solids holdups cause lower ozone concentrations due to higher reaction rates. Radial gradients of the reactant (ozone) concentrations increased in the middle section of the downer, and decreased with increasing superficial gas velocity and solids circulation rate. Contact efficiency, a measure of the interaction between gas and solids indicated high efficiency in the flow developing zone and decreased with height in the fully developed region.     

Gamma radiation aging of EVA/EPDM blends: Effect of vinyl acetate (VA) content and radiation dose on the alteration in mechanical,thermal, and morphological behavior

A series of ethylene vinyl acetate (EVA)/ethylene‐propylene diene elastomer (EPDM) blends (50/50 ratio) with four types of EVAs were prepared using brabender type batch mixer followed by compression molding. All compression‐molded samples were exposed to gamma radiation at 500, 1000, and 1500 kGy doses and were subjected to mechanical, compression set, thermal and morphological test. The % retention in tensile strength, elongation, and hardness were found higher for higher vinyl acetate (VA) containing radiation aged EVA/EPDM blends. The compression set value was decreased with increase of VA content. The thermal degradation kinetics of high VA containing irradiated blend (EVA40/EPDM) (EVA40 is 40%VA containing EVA) was found slower than those of lower VA containing blend (EVA18/EPDM). The surface morphology for EVA18/EPDM sample was transformed into more irregular one with more cracks and fragmented segments by aging at 1500 kGy dose while surface for EVA40/EPDM sample was found comparatively smooth, fine, and continuous with very few cracks and fragmented parts at similar dose. Thus, from the measured properties and morphology, it was revealed that the degree of degradation of blends kept on decreasing with increase in VA content. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46216.     

Removal of pyridine from water by pervaporation using filled SBR Membranes

Styrene butadiene rubber (SBR) was efficiently cured (crosslinked) by using sulfur to accelerator ratio less than unity. This cured SBR was further compounded with carbon black filler (grade N330) with three different doses i.e., 5, 10, and 20 wt % of filler to form three different filled and crosslinked membranes, i.e., SBR5, SBR10, and SBR20. These filled rubber membranes and one unfilled but efficiently cured membrane, i.e. SBR0, were used for pervaporative removal of pyridine from its mixtures with water. The filled membranes were found to show better selectivity and mechanical properties but lower flux than the unfilled membrane. All of these membranes showed reasonably good range of flux and pyridine selectivity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Fluorine in Drug Design: A Case Study with Fluoroanisoles

Anisole and fluoroanisoles display distinct conformational preferences, as evident from a survey of their crystal structures. In addition to altering the free ligand conformation, various degrees of fluorination have a strong impact on physicochemical and pharmacokinetic properties. Analysis of anisole and fluoroanisole matched molecular pairs in the Pfizer corporate database reveals interesting trends: 1) PhOCF₃ increases log D by ～1 log unit over PhOCH₃ compounds; 2) PhOCF₃ shows lower passive permeability despite its higher lipophilicity; and 3) PhOCF₃ does not appreciably improve metabolic stability over PhOCH₃. Emerging from the investigation, difluoroanisole (PhOCF₂H) strikes a better balance of properties with noticeable advantages of log D and transcellular permeability over PhOCF₃. Synthetic assessment illustrates that the routes to access difluoroanisoles are often more straightforward than those for trifluoroanisoles. Whereas replacing PhOCH₃ with PhOCF₃ is a common tactic to optimize ADME properties, our analysis suggests PhOCF₂H may be a more attractive alternative, and greater exploitation of this motif is recommended.     

Improved mechanical and moisture resistance property of in situ polymerized transparent PMMA/Cellulose composites

This article evaluates the role of cellulosic fillers in a synthetic polymer matrix like polymethylmethacrylate (PMMA) when incorporated by in situ suspension polymerization technique. Cellulose micro/nanofibers (CNF) were extracted from jute fibers and chemically modified with maleic anhydride (MACNF) to increase their interfacial compatibility with PMMA by participation of the MA moiety in the free radical polymerization with MMA. The effect of incorporating MACNF on the physical and mechanical properties of the PMMA matrix was investigated. Optical transparency was retained in the in situ prepared PMMA/cellulose composites (IPMC) similar to that of unreinforced PMMA. Another set of PMMA/cellulose composites was prepared by dispersing MACNF in PMMA matrix by ex situ solution dispersion method (EPMC). The modification of CNF with MA significantly improved the filler/matrix interfacial compatibility and in situ polymerization technique further enhanced the properties of the composites. The high moisture absorption tendency, which is a major drawback of the cellulose filled composites, remarkably reduced in IPMC. POLYM. COMPOS., 36:1748–1758, 2015. © 2014 Society of Plastics Engineers