Online Delay Estimation and Adaptive Compensation in Wireless Networked System: An Embedded Control Design

International Journal of Control, Automation and Systems - In the present work, an embedded PI controller is designed for speed regulation of DC servomotor over a wireless network. The embedded...     

LFMTCN: A Green Ultra-Dense Multi-tier Small Cell Network Using Leader–follower Strategy

Wireless Personal Communications - Design of energy and spectrum-efficient multi-tier small cell network is an emerging research area. This paper has addressed the challenges of power optimization...     

C2OF2N: a low power cooperative code offloading method for femtolet-based fog network

Power and delay aware cloud service provisioning to mobile devices has become a promising domain today. This paper proposes and implements a cooperative offloading approach for indoor mobile cloud network. In the proposed work mobile devices register under femtolet which is a home base station with computation and data storage facilities. The resources of the mobile devices are collaborated in such a way that different mobile devices can execute different types of computations based on cooperative federation. The proposed offloading scheme is referred as cooperative code offloading in femtolet-based fog network. If none of the mobile device can execute the requested computation, then femtolet executes the computation. Use of femtolet provides the mobile devices voice call service as well as cloud service access. Femtolet is used as the fog device in our approach. The proposed model is simulated using Qualnet version 7. The simulation results demonstrate that the proposed scheme minimizes the energy by 15% and average delay up to 12% approximately than the existing scheme. Hence, the proposed model is referred as a low power offloading approach.     

Rail-to-rail split-output SET tolerant digital gates

Analog Integrated Circuits and Signal Processing - Electronic circuits operating in the radiation intensive environment like space, are subject to a barrage of cosmic particles like neutrons,...     

Half-of-the-sites reactivity of F235C {lambda}-repressor: implications for the structure of the whole repressor

A site-directed mutation, F235C, was created at the penultimateresidue of the -repressor. Measurement of dimer–monomerdissociation constant suggested that dimer–monomer dissociationof the mutant repressor is similar to that of the wild-type.Affinity towards a single operator O_R1 is also similar to thatof the wild-type repressor. The mutant repressor gene in a multi-copyplasmid confers immunity towards infection by a cI^- lambda phage,suggesting preservation of functional integrity. Far-UV circulardichroism spectra show no major change in the secondary structure.Fluorescence quenching experiments, however, suggest increasedexposure of some tryptophan residues. The urea denaturationprofile indicates decreased stability of a part of the C-terminaldomain. Under non-denaturing conditions, cysteine-235 showshalf-of-the-sites reactivity, i.e. on average only one out oftwo cysteine-235 residues in the dimer shows reactivity towardssulfhydryl reagents. Fluorescence energy transfer between randomlylabeled donor and acceptor fluorescent probes indicates thatonly one sulfhydryl per dimer is reactive, suggesting true half-of-the-sitesreactivity. The structural role of the C-terminal tail in thewhole repressor dimer is discussed.     

Studies on semi‐interpenetrating polymer network based on nitrile rubber and poly(methyl methacrylate)

Sequential interpenetrating polymer networks (IPNs) based on nitrile rubber and poly(methyl methacrylate) (PMMA) were synthesized. IPN compositions were varied by varying the swelling time. Two methods were adopted for making IPNs. The first method is “single‐step IPN” (SIPN) and the second method is “multistep IPN” (MIPN). The compositions were fixed around 90, 80, 70, 60 and 50% of NBR. In SIPN mode, swelling in monomer and subsequent curing was done once. In MIPN mode, swelling in monomer and curing was repeatedly done. Tensile strength of IPNs was found to increase with PMMA content, MIPN showing higher strength compared to SIPN. Dynamic modulus showed a similar trend. The tan δ value was found to decrease with PMMA content. At 62/38 nitrile rubber (NBR)/PMMA, MIPN composition isolated tan δ peaks appeared near glass transition temperatures of NBR and PMMA, respectively. Scanning electron micrograph showed phase‐separated morphology at the same MIPN composition. Solvent resistance increased with IPN formation maintaining higher resistance for MIPN compared to SIPN. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 354–360, 2004     

Pore Structure of Silica Gel

The effect of washing on the texture of silica gel has been investigated in terms of parameters such as porosity, pore size distribution, surface area and absorption of moisture. It was observed that if silica gel (before activation) is washed with water containing dissolved ions such as Ca and Mg wider pores are formed at the expense of smaller ones. This phenomenon has been explained in terms of change in the size distribution of gel particles which is brought about by solution of very fine particles followed by growth, through condensation, of larger particles. The experimental observations have been interpreted to suggest guidelines to control the texture of gels by washing with solutions comaining different cations.     

Polymerization behavior of an organophosphorus monomer for use in dental restorative materials

Vibrational overtone activated polymerization of acrylonitrile (AN) has been demonstrated using two initiators, benzoyl peroxide (BP), and 2,2′‐(azobis)isobutyronitrile (AIBN). Excitation of the fifth vibrational overtone of the CH stretch of AIBN at 627 nm and BP at 604 nm initiates the reaction. Monomer conversions were monitored by a gravimetric method. In both cases, the wavelength selectivity was investigated by irradiating the monomer/initiator mixtures at the absorption maximum of the initiator, the absorption maximum of the monomer, and at a wavelength (580 nm for AN/AIBN and 625 nm for AN/BP) where neither the initiator nor the monomer absorbs light. For the AN/AIBN mixture, after 48 h the monomer conversion for the irradiation on the peak absorption of AIBN (627 nm) is about twice as large as the irradiation at 580 nm. For the AN/BP mixture, after 48 h the monomer conversion for the irradiation on the peak absorption of BP (604 nm) is about a factor of 2.2 larger than for the irradiation at 625 nm. The overall quantum yields of both polymerizations were estimated. After 48 h the overall quantum yield for the AN/AIBN mixture irradiated at the initiator absorption (Φ₆₂₇ = 21083) is about 10 times larger than for the sample irradiated at the pure monomer absorption (Φ₅₉₅ = 1942). For the AN/BP mixture, the 604 nm quantum yield (Φ₆₀₄ = 1096) is about 2.4 times larger than the 595 nm quantum yield (Φ₅₉₅ = 448). The influence of the initiator concentration is also presented. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 565–571, 2003     

Circular footings resting on geotextile-reinforced sand bed

The note pertains to an experimental study made on circular footings resting on semi-infinite layer of sand reinforced with geotextiles. Using the concept of homogenization of such soils, both analytical and numerical analyses have also been conducted to predict the load-settlement behavior and compared with experimental observations. The study highlights the effect of the footing size, number of reinforcing layers, reinforcement placement pattern and bond length and the relative density of the soil on the load-settlement characteristics of the footings.