Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.     

Swift and Selective Reduction of Nitroaromatics to Aromatic Amines with Ni–Boride–Silica Catalysts System at Low Temperature

Various nitroaromatics are successfully reduced to amines with 100% conversion and selectivity in methanol at low temperature (≈5 °C), by using versatile system of 5% Ni–SiO₂ catalyst and NaBH₄ and in situ generation of Ni boride. The catalytic efficiency of Ni loading (5%, 10% and 15%) with silica or titania as support materials is investigated for reduction of nitrobenzene. The Ni–titania/NaBH₄ system recorded lower conversion and selectivity. The IR studies indicate that silica support does not have free –OH group on its surface. Thus the nickel boride is anchored to the silica to facilitate the catalytic process.     

Distributed Transmit Antenna Selection (DTAS) Under Performance or Energy Consumption Constraints

Motivated by the transmit antenna selection (TAS) concept, used in Multiple-Input-Multiple-Output systems, we argue for distributed transmit antenna selection (DTAS), which corresponds to a method of selecting a subset of available relays in cooperative diversity systems. Assuming amplify and forward relays, the proposed selection method represents a low-complexity tool for determining the optimum relaying set. Two optimization problems are studied: the error probability minimization subject to total energy consumption constraints, and the dual one, the total energy consumption minimization under error performance constraints. Numerical examples verify the advantage of the proposed method in adapting the number of relaying terminals to the desired performance-consumption tradeoff.     

Kriterien für die Zulassung von Tierarzneimitteln gegen Zeckenbefall bei Hunden und Katzen: Ein Überblick der aktuellen Anforderungen und Möglichkeiten unter Berücksichtigung der derzeitig gültigen Leitlinien

Ohne Zusammenfassung The online version of the original article can be found under doi:.     

Investigation into Polarization of Unloaded and Loaded Microstrip Square-Ring Antennas

The polarization characteristic of unloaded and loaded square-ring microstrip antennas is investigated. Several different loading types like single-stub, dual-stub, notch, gap and shorting-pin are considered and their effects are studied. Loading enables feeding using a 50-Omega probe. The simulation and measurement results show that the loading techniques excite a loaded TMy ₁₁ mode that is orthogonal to the unloaded TMx ₁₁ mode. This indicates that by loading the ring antenna its polarization can be switched adaptively. However, the purity of the loaded and unloaded modes depends on the loading type. For some loading types like gap and shorting-pin, the excitation of the unloaded mode seems negligible, in comparison to the loadings by stub and notch. For the stub and notch loaded antennas the unloaded mode is also present, and its excitation efficiency is frequency dependent. Thus, their polarization plane, which is due to both loaded TMy ₁₁ and unloaded TMx ₁₁ modes, also becomes frequency dependant. The results of this investigation can be useful in selecting the loading methods for high-impedance microstrip ring antennas, and control of their impedance and polarization. The knowledge of the antenna polarization is essential in communications, and its dependence on the loading type can be used as an important parameter in design of adaptive antennas and sensors.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Smart phones and interactive reports leave traffic in the rearview mirror

To convey the dynamic information related to traffic conditions in various parts of a city, we propose an environment utilizing the technology of smart phones to provide information anywhere and anytime. Called ";The Interactive Traffic Beat Project,"; it uses a Web-based service to deliver this information to people through their cell phones at the right time so that valuable time can be saved and the chaos on the roads can be managed.     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

Power sector development in India with CO2 emission targets: Effects of regional grid integration and the role of clean technologies

The power sector in India at present comprises of five separate regional electricity grids having practically no integrated operation in between them. This study analyses the utility planning, environmental and economical effects of integrated power sector development at the national level in which the regional electric grids are developed and operated as one integrated system. It also examines the effects of selected CO₂ emission reduction targets in the power sector and the role of renewable power generation technologies in India. The study shows that the integrated development and operation of the power system at the national level would reduce the total cost including fuel cost by 4912 million $, total capacity addition by 2784 MW, while the emission of CO₂, SO₂ and NO_x would be reduced by 231.6 (1.9%), 0.8 (0.9%), 0.4 (1.2%) million tons, respectively, during the planning horizon. Furthermore, the study shows that the expected unserved energy, one of the indices of generation system reliability, would decrease to 26 GWh under integrated national power system from 5158 GWh. As different levels of CO₂ emission reduction targets were imposed, there is a switching of generation from conventional coal plants to gas fired plants, clean coal technologies and nuclear based plants. As a result the capacity expansion cost has increased. It was found that wind power plant is most attractive and economical in the Indian perspective among the renewable options considered (Solar, wind and biomass). Copyright © 2003 John Wiley & Sons, Ltd.     

Fractional crystallization on cooled walls: Separation efficiency with a growing crystal layer, its diffusion washing, and partial melting

The redistribution of components in the crystal layer-melt system at the main stages of fractional crystallization on cooled walls is studied. Mathematical solutions that can be used for calculating the fraction of trapped melt and the value of effective distribution (partition) coefficient in the crystallization of systems of different types are obtained. The kinetics of diffusion of impurities and migration of liquid inclusions under the action of temperature gradients at the growth and diffusion-washing stages of a two-phase crystal layer is studied. Simple relations for calculating the holdup of a melt and the maximal degree to which the main component can be purified in the partial melting (sweating) of crystal layers are derived. The theoretical results are compared with the experimental data obtained in the fractional crystallization of organic mixtures and freezing of aqueous solutions. Comparative analysis of the efficiency of the studied stages of fractional crystallization is accomplished and some practical recommendations are formulated.