Ultrastructural studies of spermiogenesis in rabbit exposed to chronic fluoride toxicity

OBJECTIVE: To compare skinfold thickness measurements with bioelectrical impedance analysis (BIA) as a measure of body fat for use in a survey of children (the National Study of Health and Growth). DESIGN: Part cross-sectional, part repeated measurement study. SETTING: A junior school in Bath. SUBJECTS: 42 boys and 33 girls aged from 9 to 11 years. INTERVENTIONS: Measurements of BIA, height, weight, and triceps, biceps, subscapular and suprailiac skinfolds. RESULTS: All measurements were highly repeatable with intraclass correlation coefficients > 0.90. The level of agreement between estimates of percentage of body fat derived from prediction equations based on impedance or skinfold measurements respectively was poor: the mean difference (impedance estimate minus skinfold estimate) was 4.67% (95% range -3.47 to 12.82) for boys and 7.81% (95% range 1.27 to 14.34) for girls. The two estimates were found to correlate highly (r = 0.83 for boys and r = 0.81 for girls) because weight, used to convert estimates of fat-free mass derived from impedance to fat mass, was highly correlated with impedance and moderately highly correlated with skinfold thicknesses. The correlations of resistance (R) and (H)2/R with skinfold thicknesses were very low. There was a moderate correlation of R and H2/R with log(weight-for-height index), but lower than that of log(weight-for-height index) with each of the skinfolds. CONCLUSIONS: As currently available equations for converting impedance-based estimates of total body water to fat mass are not fully developed for use in children of varying ages, estimates of body fat calculated from skinfold thickness measurements remain preferable in epidemiological studies of children's health and growth.     

Analysis of a soliton-based logic module for a ring network

We analyze and numerically study the code-matching logic module that is the central element in a proposed soliton-based ring network system running at peak rates of 100 Gb/s. The proposed network is packet-switched, and fast logic is required to route each packet. That is the function of the code-matching logic module, and four soliton logic gates that can perform fast logic are the key devices in its design. The behavior of the code-matching logic module is governed by a large set of parameters, and we simulate it by varying many of these parameters. The physical effects that occur in these devices and their significance are analyzed. The results indicate that the logic module will work but within a restricted parameter range     

Preparation of an anion‐exchange adsorbent by the radiation‐induced grafting of vinylbenzyltrimethylammonium chloride onto cotton cellulose and its application for protein adsorption

Poly(vinylbenzyltrimethylammonium chloride)‐graft‐cotton cellulose, an anion‐exchange matrix, was synthesized by a mutual radiation‐induced grafting technique with a ⁶⁰Co γ‐radiation source. The grafted matrix was characterized by grafting yield estimation, elemental analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The grafting yield decreased with the increase in the dose rate. However, the grafting yield and nitrogen content of grafted samples increased almost linearly with an increase in the total irradiation dose. To evaluate the performance of the grafted anion‐exchange matrix, the protein adsorption and elution behavior were investigated in a continuous column process under various experimental conditions, with bovine serum albumin used as a model protein. The binding and elution behavior of the anion‐exchange matrix depended on different experimental parameters, such as the grafting yield, ionic strength, pH of the medium, and amount of protein loaded. From a breakthrough curve, the equilibrium binding capacity and elution percentage of the grafted anion‐exchange matrix were estimated to be 40 mg/g and 94%, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5512–5521, 2006     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

Design Errors: Inefficiency or Carelessness of Designer?

Design defects are experienced in many projects; the difference is only in the extent of occurrence. This technical note discusses a design error case in a building project in Nepal, where the designer made the wrong assumptions in roof treatment work for waterproofing as well as for heat insulation purposes. From the investigation of the problem, it was found that the waterproofing polymer was not applied directly over concrete slab top. Use of heavy concrete block as a heat insulation material also helped to increase the leakage problem. The problem evoked loss of prestige for project officials, the design consortium, and the contractor.     

Improved accuracy and convergence of discretized population balance for aggregation: The cell average technique

A new discretization method for aggregation equations is developed. It is compared to the fixed pivot technique proposed by Kumar and Ramkrishna (1996a. On the solution of population balance equations by discretization—I. A fixed pivot technique. Chemical Engineering Science 51, 1311-1332). The numerical results for aggregation problems by discretized population balances are consistently overpredicting and diverge before the gelling point in the case of a gelling kernel. The present work establishes a new technique which assigns the particles within the cells more precisely. This is achieved by taking first the average of the newborn particles within the cell and then assigning them to the neighboring nodes such that pre-chosen properties are exactly preserved. The new technique preserves all the advantages of the conventional discretized methods and provides a significant improvement in predicting the particle size distribution (PSD). In addition, it is found that the technique is a powerful tool for the computation of gelling problems. The effectiveness of the technique is illustrated by application to several aggregation problems for suitably selected aggregation kernels including physically relevant kernels.     

ShOC rectifier: a new metal-semiconductor device with excellent forward and reverse characteristics

We report a new structure, called the shielded ohmic contact (ShOC) rectifier which utilizes trenches filled with a high-barrier metal to shield an Ohmic contact during the reverse bias. When the device is forward biased, the ohmic contact conducts with a low forward drop. However, when reverse biased, the Ohmic contact is completely shielded by the high-barrier Schottky contact resulting in a low reverse leakage current. Two dimensional numerical simulation is used to evaluate and explain the superior performance of the proposed ShOC rectifier.     

Liquid phase epitaxial growth of pure and doped GaSb layers: morphological evolution and native defects

Undoped and Te-doped gallium antimonide (GaSb) layers have been grown on GaSb bulk substrates by the liquid phase epitaxial technique from Ga-rich and Sb-rich melts. The nucleation morphology of the grown layers has been studied as a function of growth temperature and substrate orientation. MOS structures have been fabricated on the epilayers to evaluate the native defect content in the grown layers from theC-V characteristics. Layers grown from antimony rich melts always exhibitp-type conductivity. In contrast, a type conversion fromp- ton- was observed in layers grown from gallium rich melts below 400 C. The electron mobility of undopedn-type layers grown from Ga-rich melts and tellurium doped layers grown from Sb- and Ga-rich solutions has been evaluated. Paper presented at the poster session of MRSI AGM VI. Kharagpur. 1995