Neutron diffraction studies of the incommensurate modulation structure in SrxBa1-xNb2O6 mixed crystals of various compositions

Using time-of-flight technique between 100 K and 700 K a nearly constant IC modulation parameter is found. It depends only weakly on crystal composition. The intensity of the first-and second-order satellites decreases with temperature and at 700 K it is nearly disappeared. These facts are discussed with a view to the anti-phase domain model.     

Tracking nonstationary probabilities in adaptive binary arithmeticcoding

Adaptive arithmetic coders sometimes exhibit nonstationary symbol probabilities when coding digital halftone images with neighborhood-template models. If these nonstationary probabilities vary nonrandomly, the variations can be tracked robustly when each context derived from the coding model is expanded by conditioning on previously coded values for that model context.     

Adaptive space-time reduced-length MMSE receiver for interferencesuppression in DS/CDMA

The authors present an adaptive space-time reduced-length minimum mean-squared error (MMSE) receiver to suppress co-channel interference in the near-far environment for an asynchronous direct-sequence code-division multiple-access (DS/CDMA) system. Simulation results show that better bit-error rate and faster and more stable convergence are achieved over the existing full- and reduced-length MMSE receivers     

Einfluß der Korngröße auf mechanische Eigenschaften und den ungeschmierten reversierenden Gleitverschleiß von Al2O3-Keramik

Influence of grain size on mechanical properties and dry oscillating sliding wear of Al₂O₃-ceramics Specimens with average grain sizes varying between about 0.8 μm and 12 μm were produced by cold isostatic pressing of high purity Al₂O₃-powder followed by sintering between 1300°C and 1700°C. Hardness, Young's modulus, bending strength and fracture toughness were measured as a function of average grain sizes. Tribological tests were carried out on the different microstructures at normal laboratory air and room temperature by using a ring-on-block tribometer. Experimental results showed the dependence of mechanical properties on grain size, hardness and bending strength obeying a Hall-Petch type relation, approximately. Coefficient of friction was relatively independent of grain size under the test conditions used. However, wear intensity increased substantially if a critical grain size was surpassed. This was due to a change in mechanisms of material removal which was confirmed by scanning electron microscopical studies of the worn surfaces.     

A mathematical model for the prediction of temperature in a dry snow layer

A mathematical model for predicting the temperature in a homogeneous layer of dry snow is presented. The model, which is physically based, is capable of predicting diurnal temperature behaviour at the snow surface and at any depth within a snow layer given the variation in a limited set of meteorological parameters over that period. A sensitivity analysis is performed to determine the important parameters in the prediction of snow surface temperatures. These are found to be consistent with simple physical reasoning.     

Measurement and analysis of the step response of pyranometers requiring second-order correction

We have measured the time response of Kipp and Zonen CM-5 pyranometers to a step function of radiation and observed that the pyranometer output varied significantly from a single exponential function of time. Using a multi-exponential function to fit the experimental data, we extracted the two dominant exponential components of the signal to obtain the analytic function describing the pyranometer response. A thermal model of the pyranometer has been developed, whose response displays the observed time behaviour. The model was applied to correct the time response error of the pyranometers subject to a step function of incident radiation, and compared with a single exponential correction scheme.     

Non-linear properties of polymer cellular materials with a negative Poisson's ratio

Negative Poisson's ratio polymeric cellular solids (re-entrant foams) were studied to ascertain the optimal processing procedures which give rise to the smallest value of Poisson's ratio. The non-linear stress-strain relationship was determined for both conventional and re-entrant foams; it depended upon the permanent volumetric compression achieved during the processing procedure. Poisson's ratio of re-entrant foam measured as a function of strain was found to have a relative minimum at small strains. The toughness of re-entrant foam increased with permanent volumetric compression, and hence with density.     

Die Langzeit-Korrosionsgeschwindigkeit des passiven Eisens in anaeroben alkalischen Lösungen

The long-term corrosion rate of passive iron in anaerobic alcaline solutions Gas generation is an important issue in safety assessments of low and intermediate level radioactive repositories. In this connection the hydrogen production from corrosion of passive iron in saturated calcium hydroxide, in dilute alkali hydroxide and cement porewater solutions has been determined. The measurements were performed manometrically using fusion sealed glass cells, the measurement periods being between 275 and 560 days. In 0.1 M and 0.04 M alkali hydroxide solutions the initial hydrogen generation rate was 12 mmol/m²yr corresponding to a linear corrosion rate of 64 nm/yr. The reaction rate decreases with time. The smallest value obtained after 330 days is 0.3 mmol/m²yr corresponding to 1.5 nm/yr. The influence on iron of the saturated calcium hydroxide solution and the calcic porewater solutions differs from that of the alkali hydroxide solutions. At pH 12.5 the hydrogen generation rate remains practically constant up to breaking off the experiment, the value being about 1 mmol/m²yr corresponding to 5 nm/yr.     

The performance of a low cost clay solar cooker

This paper reports the development of a low cost clay solar cooker. The main features of this cooker are that it is made from cheap, locally available materials, and needs no skilled labour. One of the new design features of the solar cooker is the replacement of the absorber plate with locally available black sontes. The effects of using the black stones instead of the abrosber plate resulted in solar cooker capable of storing solar energy, hence making late cooking possible.