Analysis and Optimization of a Synthetic Milkweed Floral Attractant for Mosquitoes

A pentane extract of flowers of common milkweed, Asclepias syriaca (Asclepiadaceae), elicited significant orientation from both male and female Culex pipiens in a dual-port flight olfactometer. Analysis of the extract by gas chromatography-mass spectrometry revealed six major constituents in order of relative abundance: benzaldehyde, (E)-β-ocimene, phenylacetaldehyde, benzyl alcohol, nonanal, and (E)-2-nonenal. Although not all were collected from the headspace profile of live flowers, a synthetic blend of these six compounds, when presented to mosquitoes in the same levels and proportions that occur in the extract, elicited a response comparable to the extract. Subtractive behavioral bioassays demonstrated that a three-component blend consisting of benzaldehyde, phenylacetaldehyde, and (E)-2-nonenal was as attractive as the full blend. These findings suggest the potential use of synthetic floral-odor blends for monitoring or control of both male and female disease-vectoring mosquitoes.     

Vacuum desorption of gases from inorganic solvents with various boiling points

The vacuum desorption of gases from inorganic solvents with low and high boiling points is reported. A thin-film evaporator consisting of regular tubular packing elements is considered. A laminar downward cocurrent flow of liquid and vapor is analyzed. General theoretical propositions are illustrated by the example of the desorption of simple gases from lower alcohols (methanol, ethanol) and liquid naphthalene, as well as by the example of removing the products of ester decomposition from esters at high temperatures.     

Investigating the effect of nano-silica on efficiency of the foam in enhanced oil recovery

Due to the vast production of crude oil and consequent pressure drops through the reservoirs, secondary and tertiary oil recovery processes are highly necessary to recover the trapped oil. Among the different tertiary oil recovery processes, foam injection is one of the most newly proposed methods. In this regard, in the current investigation, foam solution is prepared using formation brine, C₁₉TAB surfactant and air concomitant with nano-silica (SiO₂) as foam stabilizer and mobility controller. The measurements revealed that using the surfactant-nano SiO₂ foam solution not only leads to formation of stable foam, but also can reduce the interfacial tension mostly considered as an effective parameter for higher oil recovery. Finally, the results demonstrate that there is a good chance of reducing the mobility ratio from 1.12 for formation brine and reservoir oil to 0.845 for foam solution prepared by nanoparticles.     

Plasma Spray Deposition Enhancement of Titanium Nitride Layer Using Nitrogen-Contained Plasma Irradiation of Titanium Substrate as a Pre-spraying Method

Reactive plasma spray of TiN ceramic coating attracts much attention over the years because of its ability to deposit thick layers on various metal surfaces. However, some mechanical properties of the coating such as its hardness should be improved. In this study, initially a thin layer of titanium nitride was prepared on a titanium substrate during irradiation of titanium substrate by a thermal DC nitrogen-contained plasma jet. Then, during reactive plasma spraying, Ti particles were injected into plasma jet, converted to titanium nitride and huddled on to the substrate. This new hybrid method (primary plasma irradiation and post-reactive plasma spraying) for deposition of TiN coatings would combine the advantages of both plasma-enhanced chemical vapor deposition and reactive plasma spraying methods in part. It resulted in a thick and hard layer of titanium nitride film. Sample produced by this method was analyzed with x-ray diffraction confirming titanium nitride production. Vickers hardness was measured using optical microscopy which was around 1319 H_v300g. To study the cross section of the layer, optical microscopy and scanning electron microscopy (SEM) were used.     

Encapsulation of nanoparticles by polymerization compounding in a gas/solid fluidized bed reactor

For the first time, a fluidized bed reactor was used for encapsulating nanoparticles by the polymerization compounding approach using Ziegler–Natta catalysts. The polymerization reaction was carried out using a solvent-free process in a gas-phase reactor. This direct gas–solid reaction greatly simplified collecting the particles of interest after polymerization because none of the extra steps often found in encapsulation processes, such as filtering and drying, were performed in this work. The grafting of the catalyst to the original surface of particles was confirmed by X-ray photoelectron spectroscopy. Micrographs obtained by transmission electron microscopy confirmed the presence of a thin layer of polymer, in the order of a few nanometers, around the particles. The thickness of this coating was affected by the operating conditions of the process. The characterization of the modified particles with electron microscopy also revealed that zirconia nanoparticles tend to be coated in an agglomerated state, whereas aluminum particles were mostly individually encapsulated by the polymer. In addition, the effects of temperature and pressure were studied on the encapsulation process and a kinetic analysis was presented based on the available models in the literature. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Influence of PP‐g‐MA on morphology,mechanical properties and deformation mechanism of copolypropylene/clay nanocomposite

Copolypropylene/organoclay nanocomposites are prepared by melt intercalation method in this research. Two different routes for addition of compatibilizer are examined, i.e. addition in the twin‐screw extruder along with the polymer and the clay powder simultaneously and premixing the compatibilizer with the reinforcement in a batch mixer before addition to the polypropylene (PP) matrix. Morphology, tensile and impact properties and deformation mechanisms of the samples made via two procedures are studied and compared with those of the noncompatibilized system. To study the structure of nanocomposites, x‐ray diffraction and transmission electron microscopy techniques are utilized. The deformation mechanisms of different samples are examined via reflected and transmitted optical microscopy. The results reveal that introduction of compatibilizer and also the procedure in which the compatibilizer is added to the compound, affect structure and mechanical properties of nanocomposite. The elastic modulus of PP‐clay nanocomposite has increased 11.5% with incorporation of compatibilizer. Also, introduction of organoclay without compatibilizer facilitates crazing at the notch tip of PP in 3PB testing. Incorporation of compatibilizer, however, makes difficulties in initiation and growth of crazes at the notch tip. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies on glass transition temperature of mono and bilayer protein films plasticized by glycerol and olive oil

Thermomechanical and thermal properties of whey protein, maize prolamin protein (zein), and the laminated whey protein–zein films were studied. The dynamic mechanical (thermal) analysis (DMTA) results showed that the single zein film had higher T_g than single whey protein and zein–whey laminated films. The shift in the T_g values of films from 31.2°C in whey protein film and 88.5°C in the zein film to 82.8°C in the laminated whey protein–zein films may be implied some interaction formation between the two polymers. The small tan δ peaks were observed at ?50°C in zein–glycerol films and at ?22.37°C in the whey protein films and can be related to β‐relaxation phenomena or presence of glycerol rich region in polymer matrix. Zein‐olive oil and zein–whey protein–olive oil films showed tan δ peaks corresponded the T_g values at 113.8, and 92.4°C, respectively. Thus, replacing of glycerol with olive oil in film composition increased T_g. A good correspondence was obtained when DSC results were compared with the tan δ peaks in DMTA measurements. DSC thermograms suggested that plasticizers and biopolymers remained a homogeneous material throughout the cooling and heating cycle. The results showed that T_g of zein–glycerol films predicted by Couchman and Karasz equation is very close to value obtained by DSC experiments. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation,characterization and anticorrosive properties of a novel polyaniline/clinoptilolite nanocomposite

Nanocomposite of polyaniline (PANI) with natural clinoptilolite (Clino) was prepared. Formation of nanocomposite and incorporation of polyaniline in the clinoptilolite channels was confirmed and characterized using FTIR spectroscopy studies, X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM) and cyclic voltammetry techniques. The anticorrosive properties of a 20 μm thickness coating of PANI/Clino nanocomposite with various weight ratios (1, 3 and 5%, w/w) of clinoptilolite content on iron coupons was evaluated and compared with pure polyaniline coating. According to the results in acidic environments PANI/Clino nanocomposite has enhanced corrosion protection effect in comparison to pure polyaniline coating. Comparative experiments revealed that PANI/Clino nanocomposite with 3% (w/w) clinoptilolite content has the best protective properties. Further experiments showed that the PANI/Clino nanocomposite has considerably different corrosion protection efficiencies in various corrosive environments.