Effect of persulfate on the oxidation of benzotriazole and humic acid by e-beam irradiation

These days, the use of persulfate in advanced oxidation processes (AOPs) has gained more attention as an emerging clean and efficient technology to degrade the organic pollutants. The objective of this study was to investigate the effect of the addition of persulfate on the oxidation of benzotriazole (BT) and humic acids (HAs) by irradiation. The degradation of BT (3.7 μM) was followed under the influence of persulfate addition (200-500 μM) in combination with a fixed radiation dose (15 Gy) in the absence and presence of HA (5 and 20mg/L) in deionized water. The main results obtained in this study on the degradation of BT in the presence of HA showed a different effect of S(2)O(8)(2-) addition during irradiation, depending on whether HA are oxidized or not-oxidized. (1) An inhibitory effect of S(2)O(8)(2-) was observed in the presence of non-oxidized HA. (2) The removal of BT was generally more important during irradiation in the presence of S(2)O(8)(2-) when HA is pre-oxidized. This could be explained by the different structures of humic acids. These differences of structures of HA were identified by physico-chemical parameters such as the absorbance in the UV (254 nm), the fluorescence and the SUVA measurement.     

Investigating the effect of nano-silica on efficiency of the foam in enhanced oil recovery

Due to the vast production of crude oil and consequent pressure drops through the reservoirs, secondary and tertiary oil recovery processes are highly necessary to recover the trapped oil. Among the different tertiary oil recovery processes, foam injection is one of the most newly proposed methods. In this regard, in the current investigation, foam solution is prepared using formation brine, C₁₉TAB surfactant and air concomitant with nano-silica (SiO₂) as foam stabilizer and mobility controller. The measurements revealed that using the surfactant-nano SiO₂ foam solution not only leads to formation of stable foam, but also can reduce the interfacial tension mostly considered as an effective parameter for higher oil recovery. Finally, the results demonstrate that there is a good chance of reducing the mobility ratio from 1.12 for formation brine and reservoir oil to 0.845 for foam solution prepared by nanoparticles.     

Spark plasma sintering of Al-doped ZrB2–SiC composite

This research presents the influence of Al addition on microstructure and mechanical behavior of ZrB₂–SiC ultra-high temperature ceramic matrix composite (UHTCMC) fabricated by spark plasma sintering (SPS). A 2.5?wt% Al-doped ZrB₂–20?vol% SiC UHTCMC was produced by SPS method at 1900?°C under a pressure of 40?MPa for 7?min. The microstructural and phase analysis of the composite showed that aluminum-containing compounds were formed in-situ during the SPS as a result of chemical reactions between Al and surface oxide films of the raw materials (i.e. ZrO₂ and SiO₂ on the surfaces of ZrB₂ and SiC particles, respectively). The Al dopant was completely consumed and converted to the intermetallic Al₃Zr and Al₄Si compounds as well as Al₂O₃ and Al₂SiO₅. A relative density of 99.8%, a hardness (HV5) of 21.5?GPa and a fracture toughness (indentation method) of 6.3?MPa?m^1/2 were estimated for the Al-doped ZrB₂–SiC composite. Crack bridging, branching, and deflection were identified as the main toughening mechanisms.     

Effect of Different Cosolvents on Transesterification of Waste Cooking Oil in a Microreactor

Biodiesel was prepared from waste cooking oil combined with methanol. The process was performed via transesterification in a microreactor using kettle limescale as a heterogeneous catalyst and various cosolvents under different conditions. n‐Hexane and tetrahydrofuran were selected as cosolvents to investigate fatty acid methyl esters (FAMEs). To optimize the reaction conditions, the main parameters affecting FAME% including reaction temperature, catalyst concentration, oil‐to‐methanol volumetric ratio, and cosolvent‐to‐methanol volumetric ratio were studied via response surface methodology. Under optimal reaction conditions and in the presence of the cosolvents n‐hexane and tetrahydrofuran, high FAME purities were achieved. Considering the experimental results, the limescale catalyst is a unique material, and the cosolvent method can reduce significantly the reaction time and biodiesel production cost.     

Wear Resistance of Amorphous-Crystalline Coatings with Lubricants

The results of tests of a Zr–Al–B boundary friction detonation coating in a wide range of changes under friction conditions have been presented. A comparative analysis of the obtained characteristics of friction and wear in order to evaluate the tribotechnical properties of amorphous-crystalline coatings has been carried out. These results have been compared with parallel tests of coatings based on tungsten carbide, samples of hardened steel and bronze, and the bearing of the sliding layer. The formation of solid solutions has been established and the introduction of oxygen in zirconium that corresponds to the formation on the friction surfaces of the secondary structures of the first type, a characteristic feature of which is their surface localization, ultra-dispersed structure, and ability to minimize disruption and shield unacceptable adhesion phenomena. The use of the Auger electron microscope confirmed that oxygen completely replaces the sulfur in the surface structures.     

Steam gasification of bitumen oil in presence of Ni/dolomite catalysts

An important step in developing clean energy and reducing greenhouse gas emissions is the use of clean technologies such as gasification. In this work, we were used a bubbling fluidized bed (BFB) to convert the bitumen oil into a clean syngas in presence of three kinds of Ni/dolomite catalysts. While all three catalysts were acceptable in the process of tar elimination, but DN-22 was more successful in eliminating tar than the other two samples, which might be due to the higher amount of CaO in the composition DN-22. With increase in Ni, the amount of eliminated tars in the tar cracking process was also increased due to the delay in the deactivation of the dolomite catalyst.     

Estimation of optimum binder content of recycled asphalt incorporating a wax warm additive using response surface method

This paper presents a new approach to estimate the optimum binder content (OBC) of recycled asphalts (RAs) incorporating a warm mix additive based on the interaction effects of compaction temperature, RA content and binder content using volumetric and strength characterisation. The experimental design was developed using response surface method (RSM) based on central composite design for various compaction temperatures (130–160 °C), RA contents (30–50%) and binder contents (4.9–6.0%). Laboratory tests were performed and analysed to meet the desired volumetric and strength properties according to the Malaysian specifications for the design of dense asphalt mixtures. Statistical analysis and mathematical models proposed by RSM were used to determine the OBC. The results showed that compaction temperature is the most significant factor in determining the OBC. There are minimum differences in the OBC variation of samples incorporating different dosage of RA. The developed model can be used for quick estimation of OBC for various levels of compaction temperature and RA content.     

A literature review on MHE selection problem: levels,contexts, and approaches

This paper presents a review on selection problem of material handling equipment (MHE) and general equipment used in industry area. The issue on MHE is widely paid attention since MHE has contribution on material, good and product accomplishment. Few methods and softwares have been proposed and developed to select the most appropriate MHE for a complex selection problem. Today’s high diverisity of MHE categories and types influence the generation of many possible choices which leads to the complexity. In this paper, a further discussion in terms of MHE and equipment including three major points namely level of selection, the context of selection problem and the approaches are served to highlight the complex MHE selection according to the number of possible choices provided, to analyse the consideration for the problem context, and to reveal the superior method for complex MHE selection. Forty-two papers collected from the past study are presented asscociating each point of the discussion.     

Time‐domain hybrid formulations for wave simulations in three‐dimensional PML‐truncated heterogeneous media

We are concerned with the numerical simulation of wave motion in arbitrarily heterogeneous, elastic, perfectly‐matched‐layer‐(PML)‐truncated media. We extend in three dimensions a recently developed two‐dimensional formulation, by treating the PML via an unsplit‐field, but mixed‐field, displacement‐stress formulation, which is then coupled to a standard displacement‐only formulation for the interior domain, thus leading to a computationally cost‐efficient hybrid scheme. The hybrid treatment leads to, at most, third‐order in time semi‐discrete forms. The formulation is flexible enough to accommodate the standard PML, as well as the multi‐axial PML. We discuss several time‐marching schemes, which can be used à la carte, depending on the application: (a) an extended Newmark scheme for third‐order in time, either unsymmetric or fully symmetric semi‐discrete forms; (b) a standard implicit Newmark for the second‐order, unsymmetric semi‐discrete forms; and (c) an explicit Runge–Kutta scheme for a first‐order in time unsymmetric system. The latter is well‐suited for large‐scale problems on parallel architectures, while the second‐order treatment is particularly attractive for ready incorporation in existing codes written originally for finite domains. We compare the schemes and report numerical results demonstrating stability and efficacy of the proposed formulations. Copyright © 2014 John Wiley & Sons, Ltd.