The mechanical properties and tensile failure mechanism of a high strength polymer modified Portland cement

The mechanical properties of one of the new high strength polymer modified hydraulic cements have been investigated. An important parameter for the material is the amount of polymer present, and the properties are found to be dependent upon the degree of drying. For example, in the wet state, polymer content has little effect upon ultimate flexural strength, but does cause nonlinearity in the stress-strain behaviour. Although increasing polymer content causes a reduction in the initial tangent modulus, it is shown that retardation of hydration may account for this. In the dry state, increasing polymer content leads to increasing flexural strength, fracture toughness and failure strain, but leaves initial elastic modulus relatively unchanged. It is concluded that removal of pores is not the principal strengthening mechanism since strength increases are consequent upon water removal from the microstructure in the presence of the polymer. A fibrillar pull-out model is proposed to explain the observed behaviour of both wet and dry material and ordinary Portland cement paste, which shows good correlation with experimental results. The principal effect of the polymer is to act as an adhesive at the interface between interacting CSH fibrils.     

Lysosomal proteinases in muscle tissue and leukocytes of meat animals

Carboxypeptidases A and B, cathepsins B, D and E, dipeptidyl aminopeptidase 1 and collagenase were extracted from bovine and porcine leukocyte lysosomes and diaphragm muscle lysosomes with 4% n-butyl alcohol in dry ice and various chemical properties were studied. The enzymes were classified by their specific activities with different substrates, pH optima, energies of activation and the influence of inhibitors and stimulators. Cathepsins D and E were the most active proteases studied and all enzymes were more active in leukocytes than in sediments from muscle tissue. The properties of these enzymes, compared with enzymes from other sources, and their possible involvement in meat tenderness are discussed.     

An intrinsic dimensionality estimator from near-neighbor information

The intrinsic dimensionality of a set of patterns is important in determining an appropriate number of features for representing the data and whether a reasonable two- or three-dimensional representation of the data exists. We propose an intuitively appealing, noniterative estimator for intrinsic dimensionality which is based on nearneighbor information. We give plausible arguments supporting the consistency of this estimator. The method works well in identifying the true dimensionality for a variety of artificial data sets and is fairly insensitive to the number of samples and to the algorithmic parameters. Comparisons between this new method and the global eigenvalue approach demonstrate the utility of our estimator.     

Involvement of Ventral Pallidum in Prefrontal Cortex-Dependent Aspects of Spatial Working Memory.

Ventral pallidum (VP) is an important source of limbic input to medial thalamus. Three studies examined the role of VP in spatial memory tasks impaired by medial thalamic lesions. In the 1st study, rats with VP lesions were impaired performing delayed matching trained with retractable levers (DMRL), a measure sensitive to prefrontal (but not hippocampal) damage. The 2nd study demonstrated dose-dependent DMRL impairment following microinjection of gamma-aminobutyric acidA, glutamate, or mu-opioid agonists in VP. In the 3rd study, VP lesions had no effect on varying choice radial-maze delayed nonmatching, a measure sensitive to hippocampal (but not prefrontal) lesions. These results suggest a common role in spatial memory for VP and other components of prefrontal-ventral striatopallidothalamic circuits distinct from hippocampal function. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Comparison of the wear resistance of various grades of cemented carbides that may find application in wood machining

A laboratory test is described in which specimens of rectangular cemented carbide tool inserts of a standard size are allowed to slide against a rapidly rotating fiberboard disc in either the presence or the absence of a mist spray of a dilute organic acid (tannic acid or acetic acid) to simulate the cutting of green wood and cured wood respectively. It is shown that the worn surfaces of cemented carbide tools used in (field) service are remarkably similar to the worn surfaces of specimens used in the laboratory (simulation) tests.Extensive results are presented that show quantitatively the progressive wear of a wide range of cemented carbides as a function of time for sliding under wet and dry conditions. It is shown that wear depends on the type and amount of binder present in the cemented carbide and on the nature of the environment. Materials with Co-Cr and Ni-Cr binders containing significant amounts of chromium showed the greatest resistance to wear.     

Surface damage during machining of annealed 18% nickel maraging steel Part 1 — Unlubricated conditions

The effect of cutting speed and tool wear land length on the surface damage produced during the machining of annealed 18% nickel maraging steel under dry orthogonal conditions was determined. Machined test pieces were examined with a scanning electron microscope and an optical microscope. Surface roughness was determined with a profilometer.The results of the investigation show that during machining a wide variety of different forms of surface damage is generated. The machined surfaces show extended regions where both coarse and fine scale surface damage have occurred at cutting speeds up to 0.1 m s^?1, whereas at cutting speeds greater than 0.1 m s^?1 the surfaces show evidence only of fine scale surface damage. It is suggested that the regions of coarse scale surface damage are associated with the phenomenon of partially discontinuous chip formation and the nucleation of cracks in the vicinity of the tool nose region. Several mechanisms of crack nucleation and propagation, which are thought to account for the occurrence of many aspects of the surface topography observed, are presented and discussed. It is suggested also that the regions of fine scale surface damage are associated with the phenomenon of continuous chip formation and interaction between the tool nose region and the freshly machined workpiece surface.It is shown that scanning electron microscopy is more indicative of the true condition of the surface than surface roughness measurements.     

The role of tool composition and tool geometry in controlling the surface finish in machining wood

An examination of several brazed cemented carbide tool inserts that were used in service for cutting cured (dry) pine is described. A laboratory test is also described where the relative resistance to chipping of the brazed tool inserts was measured.It is shown that tool wear occurs through a continuous increase in the tool cutting edge radius that produces a deterioration in the appearance of the machined surface. It is also shown that an increase in either the binder volume fraction or the tool wedge angle produces an increase in the energy absorbed on impact. It is suggested that if progressive wear determines the useful life of a cemented carbide cutting tool then a low volume fraction of binder is required whereas if tool edge chipping determines the useful life of a cutting tool then a large volume fraction of binder and a large tool wedge angle are required.