IEEE802.11p下删余卷积编码译码方法的研究

应用于智能交通系统的无线接入协议IEEE802.11p,其物理层卷积编码的码率可通过对(2,1,7)卷积编码器的删余来实现。讨论了删余位置的图案和算法,分析了在删余位置插入不同哑元时维特比译码后误码率的统计特性。仿真的同时比较了固定哑元下不同码率所引入的误比特率。     

基于增广矩阵束方法的平面天线阵列综合

针对平面阵列的稀布优化问题,提出了一种基于增广矩阵束方法的减少阵元数目、求解阵元位置和设计幅度激励的优化方法。首先对期望平面阵的方向图进行采样并由采样点数据构造增广矩阵,对此矩阵进行奇异值(SVD)分解,确定在误差允许范围内所需的最小阵元数目;然后基于广义特征值分解分别计算两组特征值,并根据类ESPRIT算法对特征值进行配对;最后在最小二乘准则条件下根据正确的特征值对求解平面阵列的阵元位置和激励。仿真结果表明该算法具有较高的计算效率和数值精度。     

Constrained adaptive optimal control using a reinforcement learning agent

To synthesize the optimal control strategies of nonlinear systems on infinite horizon while subject to mixed equality and inequality constraints has been a challenge to control engineers. This paper regards it as a problem of finite-time optimization in infinite-horizon control then devises a reinforcement learning agent, termed as the Adaptive Optimal Control (AOC) agent, to carry out the finite-time optimization procedures. Adaptive optimal control is in the sense of activating the finite-time optimization procedure whenever needed to improve the control strategy or adapt to a real-world environment. The Nonlinear Quadratic Regulator (NQR) is shown a typical example that the AOC agent can find out. The optimality conditions and adaptation rules for the AOC agent are deduced from Pontryagin’s minimum principle. The requirements for convergence and stability of the AOC system are shown.     

The oxidation state of sulfur detected in Na2O-CaO-SiO2 float glass by X-ray absorption near edge structure spectra

The oxidation state of sulfur is detected in Na2O-CaO-SiO2 float glass by synchrotron radiation X-ray absorption near edge structure (XANES) spectra at the sulfur K edge. The measured spectra show the only presence of S6+ in the Na2O-CaO-SiO2 float glass and the oxidation state of sulfur do not change with the increase of glass depth. It is also found that, after the melt has gone through the molten tin bath, the S6+ is the dominant species, but S2- is also present on both surfaces. It is not certain whether cation bonds to S2- or not, because there are many cations dissolved in the melted tin which makes the spectrum complicated.     

聚合物在离子选择电极上的应用

本文概述了聚合物膜离子选择电极的发展,制备、应用等方面的研究情况;将聚合物膜离子选择电极分为固态膜类和液态膜类,分别对其优缺点和发展前景加以分析;并讨论了聚合物在敏感膜中的作用,以及聚合物结构对敏感膜性能的可能影响。     

工程训练教学模式与运行机制的改革探讨

文章对广东工业大学工程训练中心教学的现状和不足进行了分析，对其教学模式与运行机制的改革提出几点设想，以适应新形势发展的需要。     

DNA immobilization and SAW response in ZnO nanotips grown on LiNbO3 substrates.

DNA immobilization enhancement is demonstrated in a structure consisting of ZnO nanotips on 128 degrees Y-cut LiNbO3. The ZnO nanotips are grown by metalorganic chemical vapor deposition (MOCVD) on the top of a SiO2 layer that is deposited and patterned on the LiNbO3 SAW delay path. The effects of ZnO nanotips on the SAW response are investigated. X-ray diffraction and scanning electron microscopy are used to analyze the ZnO nanotips, which are of single crystalline quality, and they are uniformly aligned with their c-axis perpendicular to the substrate surface. The photoluminescence (PL) spectrum of the ZnO nanotips shows strong near bandedge transition with insignificant deep level emission, confirming their good optical property. DNA immobilization enhancement is experimentally validated by radioactive labeling tests and SAW response changes. The ZnO nanotips enhance the DNA immobilization by a factor of 200 compared to ZnO film with flat surface. DNA hybridization with complementary and noncomplementary second strand DNA oligonucleotides is used to study the selective binding of the structure. This device structure possesses the advantages of both traditional SAW sensors and ZnO nanostructures.     

Formation of CaO-TiO2-MgO-Al2O3 dual phase inclusion in Ti stabilized stainless steel

The formation of CaO-TiO2-MgO-Al2O3 dual phase inclusion in 321 stainless steel was investigated in the laboratory. The result indicated that the condition for the formation of CaO-TiO2-MgO-Al2O3 in 321 steel is [Ca]〉0.001wt%, [Ti]〉0.1wt%, and [A1]〉0.01wt%. The mechanism is the following： Al2O3 inclusion turns into CaO-Al2O3 after Ca-Si wire is fed into the molten steel; [Mg] is then obtained by reducing MgO in slag or crucible wall by [Al] and [Ti]; finally CaO-Al2O3 inclusion is changed into CaO-TiO2-MgO-Al2O3 by the reaction with [Mg], [Ti], and [O] in the molten steel simultaneously.