Modulation of stability properties of bovine trypsin after in vitro structural changes with a variety of chemical modifiers

Controlled chemical modification of enzymes, targeting groups not involved in the active site, can lead to modified catalysts that are intrinsically more efficient and resistant to heat and denaturing agents. Bovine pancreatic trypsin was covalently modified up to 75-85% with monomeric glutaraldehyde (MGA), polymeric glutaraldehyde (PGA), oxidized sucrose and oxidized sucrose polymers (OSP 70 and OSP 400). Virtually no loss in activity occurred upon modification. Temperature optima of trypsin shifts from 45-76 degrees C and T50 from 54-76 degrees C for the best modified sample made with OSP. The efficiency of the modifiers in stabilization was ranked in the order: OSP 400-T > OSP 70-T > PGA-T > MGA-T > Sucrose-T. Half-life of modified enzymes also followed the same trend. Both stabilization factor and t1/2 decreased with increasing temperatures. The free energy of activation for inactivation delta(deltaG*) varies from 12-20 kJ/mol and the activation enthalpy delta(deltaH*) of the modified trypsin by 80-120 kJ/mol indicating stabilization. Inactivation of modified trypsin by urea is less noticeable. The character of the two-step inactivation process of trypsin changes with the degree of stabilization in that the duration of phase I one increased noticeably as stabilization increases. Native trypsin fluoresces less intensely showing a red shift under the influence of denaturation. Such a fluorescence change is not so obvious for the modified enzymes indicating conformational stability acquired by modification.      

High Temperature Millimeter Wave Radiometric and Interferometric Measurements of Slag-Refractory Interaction for Application to Coal Gasifiers

Millimeter wave (MMW) radiometry can be used for simultaneous measurement of emissivity and temperature of materials under extreme environments such as in slagging coal gasifiers, where sensors have been identified as a key enabling technology need for process optimization. We present a dual-channel MMW heterodyne radiometer with active interferometric capability that allows simultaneous measurements of sample temperature, emissivity, and flow dynamics. Interferometric capability at 137 GHz is supplied via a probe signal originating from a local oscillator allowing monitoring of sample dynamics such as volume expansion and thickness change. This capability has been used to monitor characteristic behavior between refractories and slag such as slag infiltration, slag melting, viscous flow, foaming, and crucible corrosion by the molten slag. These results show the promise of the MMW system for extracting process parameters from operating slagging coal gasifiers, providing valuable information for process efficiency, control, and increased productivity.     

Induced crystallization of cellulose in never-dried cotton fibers

In the present investigation, we have made a systematic study of the induced crystallization in never-dried cotton fiber, by allowing it to desiccate under different conditions of humidity and temperature. The resulting structural changes have been followed using x-ray diffraction and infrared absorption techniques. A slow rate of drying coupled with a high temperature was more conducive for maximum crystallization. Analysis of the effect of temperature on the induced crystallization showed possible existence of a thermal transition in cellulose around 30°C. The induced crystallization brought about by slow drying as well as those produced using intercrystalline swelling agents, have been shown to be resulting from a proper channelization of the interfibrillar mobility existing in the never-dried fibers.     

Electrochemical etching of highT c superconducting materials

HighT _c superconductor materials of yttrium barium copper oxide (YBCO) have been etched by a new electrochemical technique. In this technique, acids like hydrochloric, nitric and phosphoric have been used as an electrolyte and etching has been achieved with acid dilutions as high as 1:200 with water. It is observed that rapid and controlled etching is possible by this technique.     

Influence of Process Parameters on Cu–Fly Ash Composite by Powder Metallurgy Technique

In this study influence of compaction pressure, sintering temperature, and sintering time on mechanical and wear behavior of the fly ash reinforced copper-based composites are analyzed. The composites were prepared by powder metallurgy (P/M) technique with copper as matrix, 5 and 10 wt% of fly ash as reinforcement. The green compacts were prepared at three different pressures such as 350, 400, and 450 MPa. The prepared green composites were sintered at 700, 800, and 900 °C for the time period of 30, 60, and 90 min, respectively. From the results it is observed that when the process parameter increases the density, hardness, compression strength, and wear resistance increases.     

Synthesis,bioactivity and preliminary biocompatibility studies of glasses in the system CaO–MgO–SiO<Subscript>2</Subscript>–Na<Subscript>2</Subscript>O–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–CaF<Subscript>2</Subscript>

New compositions of bioactive glasses are proposed in the CaO–MgO–SiO₂–Na₂O–P₂O₅–CaF₂ system. Mineralization tests with immersion of the investigated glasses in simulated body fluid (SBF) at 37°C showed that the glasses favour the surface formation of hydroxyapatite (HA) from the early stages of the experiments. In the case of daily renewable SBF, monetite (CaHPO₄) formation competed with the formation of HA. The influence of structural features of the glasses on their mineralization (bioactivity) performance is discussed. Preliminary in vitro experiments with osteoblasts’ cell-cultures showed that the glasses are biocompatible and there is no evidence of toxicity. Sintering and devitrification studies of glass powder compacts were also performed. Glass-ceramics with attractive properties were obtained after heat treatment of the glasses at relatively low temperatures (up to 850°C).     

Compact analytical model for single gate AlInSb/InSb high electron mobility transistors

We have developed a 2D analytical model for the single gate Al In Sb/In Sb HEMT device by solving the Poisson equation using the parabolic approximation method.The developed model analyses the device performance by calculating the parameters such as surface potential,electric field distribution and drain current.The high mobility of the Al In Sb/In Sb quantum makes this HEMT ideal for high frequency,high power applications.The working of the single gate Al In Sb/In Sb HEMT device is studied by considering the variation of gate source voltage,drain source voltage,and channel length under the gate region and temperature.The carrier transport efficiency is improved by uniform electric field along the channel and the peak values near the source and drain regions.The results from the analytical model are compared with that of numerical simulations(TCAD) and a good agreement between them is achieved.