Reinforcing bars, popularly termed “rebars,” are used to impart tensile strength to concrete structures. Concrete has high resistance to weathering and fire and high compressive strength but almost no tensile strength, hence rebars are used to provide the latter to concrete. Property consistency along the length of rebars is an important prerequisite. When the finished product is subjected to thermomechanical treatment (TMT), proper control of rolling and water box parameters and efficient pinch rolling are needed to achieve acceptable properties. Variation of yield strength (YS) along TMT bars from the front to back end has been observed within the same heat treatment. In the presented investigation, it was observed that pinch rolling ineffectiveness is the main reason for the poor mechanical properties at the back end. The pinch roller was unable to support the back end of the TMT bars properly to maintain the speed and tension of the bars, resulting in nonuniform cooling of the back end through the water box and subsequent mechanical property failure. Due to the substandard material of the pinch roller, it was unable to hold the back end of the bar properly. Based on analysis of the roller it was concluded that it failed due to improper microstructure, resulting in inadequate hardness and toughness for the stringent operating conditions. AISI H13 is a better material to use in such high-service-temperature conditions. Moreover, proper heat treatment is needed to achieve adequate hardness and microstructure properties. After proper heat treatment of pinch rollers, their service life was increased twofold, minimizing the YS variation along the rebars. 相似文献
Nanocomposites of biobased thermoplastic polyurethane (TPU) from dimer fatty acids and halloysite nanotubes (HNT) were elaborated by different melt processing routes such as direct mixing (1 step process) and masterbatch/dilution (2 steps process), at different temperatures (150 and 180 °C). Rheological and transmission electron microscopy (TEM) analyses indicated that the HNT distribution and dispersion were dependent on the processing conditions: the 2 steps process produced well dispersed nanocomposites and the masterbatch dilution at 180 °C improved the HNT distribution through the TPU. Consequently, a high reinforcement was achieved, with a 40% increase in the elastic modulus and 8 °C increase in the relaxation temperature related to the glass transition of the TPU soft segments. Furthermore, a percolated network was attained, even if a large extent of HNT breaking was observed during processing, suggesting that a synergistic effect between the HNT particles and the TPU's hard segments in the molten state occurred. Thus, HNT nanotubes can be seen as highly reinforcing nanofillers when good dispersion and distribution are achieved through the polymeric matrix. 相似文献
Natural slopes consist of non-homogeneous soil profiles with distinct characteristics from slopes made of homogeneous soil. In this study, the limit equilibrium modified pseudo-dynamic method is used to analyze the stability of two-layered c-φ soil slopes in which the failure surface is assumed to be a logarithmic spiral. The zero-stress boundary condition at the ground surface under the seismic loading condition is satisfied. New formulations derived from an analytical method are proposed for the predicting the seismic response in two-layered soil. A detailed parametric study was performed in which various parameters (seismic accelerations, damping, cohesion, and angle of internal friction) were varied. The results of the present method were compared with those in the available literature. The present analytical analysis was also verified against the finite element analysis results. 相似文献
The thermal performance of a solar air collector (SAC) is investigated experimentally under the different climatic conditions of north eastern India using fuzzy logic based expert system (FLES). The FLES based on subtractive clustering (SC) with the fuzzy logic method where here, SC is used for extraction of optimal fuzzy IF-THEN rules while a fuzzy logic is used for modeling of SAC variables. This work considered four input variables [like mass flow rate (m), collector tilt angles (θ), solar radiation (Q), temperature (T)] and the four output variables [i.e. efficiency (η), exergetic efficiency (ηII), temperature rise (∆T), and pressure drop (∆P)]. First, 272 trials of experimentation on SAC are performed by varying m from 0.0078 to 0.0118 kg/s and θ from 30 to 60°, whereas the variation of metrological data is obtained in different working days. Then modeling and parametric analysis is carried out for SAC. Experimental results reveal that the value of η increases with the increase in m, Q, T and θ up to 45°. The higher value of m results in a higher value of ∆P and that reduces the value of ηII. Also, FLES model provides comparable and acceptable values for SAC. At last, validation of the FLES model is done via published data to confirm the results.
Observation of highly dynamic processes inside living cells at the single molecule level is key for a better understanding of biological systems. However, imaging of single molecules in living cells is usually limited by the spatial and temporal resolution, photobleaching and the signal-to-background ratio. To overcome these limitations, light-sheet microscopes with thin selective plane illumination, for example, in a reflected geometry with a high numerical aperture imaging objective, have been developed. Here, we developed a reflected light-sheet microscope with active optics for fast, high contrast, two-colour acquisition of -stacks. We demonstrate fast volume scanning by imaging a two-colour giant unilamellar vesicle (GUV) hemisphere. In addition, the high contrast enabled the imaging and tracking of single lipids in the GUV cap. The enhanced reflected scanning light-sheet microscope enables fast 3D scanning of artificial membrane systems and potentially live cells with single-molecule sensitivity and thereby could provide quantitative and molecular insight into the operation of cells. 相似文献
Asymmetric patchy Ag/Cu Janus nanoparticles (NPs) were synthesized via a “seed-mediated” approach. This is the first report of synthesis of nanometer sized metal-based Janus NPs without using complicated methods. Selective adsorption of the surfactant onto the seed NPs leads to the formation of Janus type structure. Subsequently the reduction potential of Ag+/Ag0 and Cu2+/Cu0 systems directs the formation of the “patch”. The patchy Janus NPs show significant antifungal activity towards a potent rice pathogen thus offering the prospect of future application in crop protection. 相似文献
Scalable fabrication of carbon nanotube (CNT) bundles is essential to future advances in several applications. Here, we report on the development of a simple, two-step method for fabricating vertically aligned and periodically distributed CNT bundles and periodically porous CNT films at the sub-micron scale. The method involves laser interference ablation (LIA) of an iron film followed by CNT growth via iron-catalyzed chemical vapor deposition. CNT bundles with square widths ranging from 0.5 to 1.5 μm in width, and 50-200 μm in length, are grown atop the patterned catalyst over areas spanning 8 cm(2). The CNT bundles exhibit a high degree of control over square width, orientation, uniformity, and periodicity. This simple scalable method of producing well-placed and oriented CNT bundles demonstrates a high application potential for wafer-scale integration of CNT structures into various device applications, including IC interconnects, field emitters, sensors, batteries, and optoelectronics, etc. 相似文献
The synergistic relationship between structure and the bulk properties of polyelectrolyte multilayer (PEM) films has generated tremendous interest in their application for loading and release of bioactive species. Layer‐by‐layer assembly is the simplest, cost effective process for fabrication of such PEMs films, leading to one of the most widely accepted platforms for incorporating biological molecules with nanometre precision. The bulk reservoir properties of PEM films render them a potential candidate for applications such as biosensing, drug delivery and tissue engineering. Various biomolecules such as proteins, DNA, RNA or other desired molecules can be incorporated into the PEM stack via electrostatic interactions and various other secondary interactions such as hydrophobic interactions. The location and availability of the biological molecules within the PEM stack mediates its applicability in various fields of biomedical engineering such as programmed drug delivery. The development of advanced technologies for biomedical applications using PEM films has seen rapid progress recently. This review briefly summarises the recent successes of PEM being utilised for diverse bio‐applications.Inspec keywords: polymer electrolytes, multilayers, polymer films, molecular biophysics, biomedical materials, biochemistryOther keywords: bioapplications, polyelectrolyte multilayer films, bioactive species, layer‐by‐layer assembly, biological molecules, biosensing, drug delivery, tissue engineering, biomolecules, proteins, DNA, RNA, electrostatic interactions, secondary interactions, hydrophobic interactions, biomedical engineering, programmed drug delivery, biomedical applications, PEM films相似文献
The electrochemical behavior of copper oxide nanoparticles is investigated at both the single particle and at the ensemble level in neutral aqueous solutions through the electrode‐particle collision method and cyclic voltammetry, respectively. The influence of Cl? and NO3? anions on the electrochemical processes occurring at the nanoparticles is further evaluated. The electroactivity of CuO nanoparticles is found to differ between the two types of experiments. At the single‐particle scale, the reduction of the CuO nanoparticles proceeds to a higher extent in the presence of chloride ion than of nitrate ion containing solutions. However, at the multiparticle scale the CuO reduction proceeds to the same extent regardless of the type of anions present in solution. The implications for assessing realistically the environmental fate and therefore the toxicity of metal‐based nanoparticles in general, and copper‐based nanoparticles in particular, are discussed. 相似文献