Mechanical and dynamic mechanical properties of jute fibers–Novolac–epoxy composite laminates

A study was done of jute composite using a polymer matrix of epoxidized Novolac resin (ENR), diglycidyl ether of bisphenol A (DGEBA)–based epoxy, and their blends with different weight percentages of the resins. It was found that on blending ENR with DGEBA, the storage modulii at room temperature are enhanced by about 100% or more in the case of 30 and 40% ENR‐containing matrices, whereas the enhancement in the case of 20 and 12% ENR‐containing matrices is only 50% that of the pure matrix. It was also observed that the tan δ peak heights of the composites containing 30 and 40% ENR are closer to that of 20% ENR‐containing composite. The probable explanation drawn on the basis of experimental findings of DMA and mechanical analysis is that by blending ENR with DGEBA epoxy it is possible to manufacture jute composites with increased stiffness without sacrificing their ductility. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2800–2807, 2002     

Studies on cocurrent gas-liquid flow in helically coiled tubes. II. Theory and experiments on turbulent mass transfer with and without chemical reaction

Pure carbon dioxide was absorbed into distilled water and sodium hydroxide solution, in cocurrent two phase annular flow in helically coiled tubes in order to measure physical and chemical mass transfer coefficients and interfacial areas. (k*_La) was correlated by the pressure drop in the test sections and interfacial areas were found to vary with the liquid phase energy dissipation. According to a new theory, (k*_L) has been shown to be a function of the root mean square vorticity near the interface. The root mean square vorticity has been related to the pressure drop, gas density, liquid flow rate and liquid velocity. The physical mass transfer coefficients theoretically predicted are in good agreement with experimental results.     

Designing multilayered wire‐grid polarizers using a monochromatic recursive convolution finite‐difference time‐domain algorithm

Multilayered wire‐grid polarizers (WGP) find application as low‐reflection polarizers in projection‐type liquid crystal display devices. A multilayered WGP is formed by adding thin layers on top of the metal ridges of an ordinary WGP. The ordinary WGP consists of a periodic array of parallel metal ridges, where the period of the array and the width of any individual metal ridge are typically less than the wavelength of the incident light. Such WGPs are often used as efficient polarizers. However, in certain applications, it is important to reduce the reflection from the WGP while preserving the polarization efficiency. One of the ways to achieve this goal is to add thin layers on top of the metal ridges of the ordinary WGP. The reduction in reflection from the multilayered WGP depends on the number and material of these additional layers. In this paper, we describe a design method for multilayered WGPs based on an effective medium theory, thin‐film computation method and a monochromatic recursive convolution finite‐difference time‐domain algorithm. The goal of design process is to identify suitable materials and thicknesses for the additional thin layers needed to lower the reflection appreciably. The design method is explained with the help of bilayered WGPs.     

Flash pyrolysis of coal: effect of nitrogen,argon and other atmospheres in increasing olefin concentration and its significance on the mechanism of coal pyrolysis

Samples of three Indian coals, of widely differing origin and rank, were subjected to flash pyrolysis at a temperature of about 1150 °C for 30 s in vacuo, and under atmospheres of nitrogen, argon, ammonia, and perdeuterobenzene. The gaseous products of the pyrolyses were analysed by infra-red and mass spectroscopy and by gas chromatography. Observed variations in gas compositions are discussed relative to the possible mode of influence by the pyrolytic atmospheres. It would appear that the pyrolytic atmosphere is an important factor in determining the composition of the pyrolysis products; the influence of nitrogen, argon and perdeuterobenzene is a physical one, leading especially to higher yields of olefins.     

Quote examiner: verifying quoted images using web-based text similarity

Over the last few years, there has been a rapid growth in digital data. Images with quotes are spreading virally through online social media platforms. Misquotes found online often spread like a forest fire through social media, which highlights the lack of responsibility of the web users when circulating poorly cited quotes. Thus, it is important to authenticate the content contained in the images being circulated online. So, there is a need to retrieve the information within such textual images to verify quotes before its usage in order to differentiate a fake or misquote from an authentic one. Optical Character Recognition (OCR) is used in this paper, for converting textual images into readable text format, but none of the OCR tools are perfect in extracting information from the images accurately. In this paper, a method of post-processing on the retrieved text to improve the accuracy of the detected text from images has been proposed. Google Cloud Vision has been used for recognizing text from images. It has also been observed that using post-processing on the extracted text improved the accuracy of text recognition by 3.5% approximately. A web-based text similarity approach (URLs and domain name) has been used to examine the authenticity of the content of the quoted images. Approximately, 96.26% accuracy has been achieved in classifying quoted images as verified or misquoted. Also, a ground truth dataset of authentic site names has been created. In this research, images with quotes by famous celebrities and global leaders have been used. A comparative analysis has been performed to show the effectiveness of our proposed algorithm.

     

Effect of binder-phase modification and Cr3C2 addition on properties of WC-IOC0 cemented carbide

For production of fine-grained and corrosion-resistant tungsten carbide (WC) based cemented carbides, addition of chromium carbide (Cr₃3C₂) in small amounts is standard practice. No systematic study, however, has been made of the effects of large additions (maximum 6 wt % ) of Cr₃C₂ as a substitute for tungsten carbide. This study focuses on the effect of hard-phase substitution by C₃C₂ in WC-1OCo cemented carbide. An attempt is also made to modify the binder metal cobalt by partial or complete substitution of nickel. Specimens were prepared using the standard liquid-phase sintering process and were tested for sintered porosity, mechanical properties, corrosion resistance, and microstructural parameters. Results confirm the findings of earlier workers regarding grain refinement and improvement of mechanical properties upon the addition of small amounts (<2 wt%) of Cr₃C₂. Modification of the binder phase improves indentation fracture toughness and corrosion resistance. Addition of Cr₃C₂ independent of the binder type improves corrosion resistance.     

Fault tolerant multiple event detection in a wireless sensor network

With an increasing acceptance of Wireless Sensor Networks (WSNs), the health of individual sensor is becoming critical in identifying important events in the region of interest. One of the key challenges in detecting event in a WSN is how to detect it accurately transmitting minimum information providing sufficient details about the event. At the same time, it is also important to devise a strategy to handle multiple events occurring simultaneously. In this paper, we propose a Polynomial-based scheme that addresses these problems of Event Region Detection (PERD) by having a aggregation tree of sensor nodes. We employ a data aggregation scheme, TREG (proposed in our earlier work) to perform function approximation of the event using a multivariate polynomial regression. Only coefficients of the polynomial (P$P$) are passed instead of aggregated data. PERD includes two components: event recognition and event report with boundary detection. This can be performed for multiple simultaneously occurring events. We also identify faulty sensor(s) using the aggregation tree. Performing further mathematical operations on the calculated P$P$ can identify the maximum (max) and minimum (min) values of the sensed attribute and their locations. Therefore, if any sensor reports a data value outside the [min, max] range, it can be identified as a faulty sensor. Since PERD is implemented over a polynomial tree on a WSN in a distributed manner, it is easily scalable and computation overhead is marginal. Results reveal that event(s) can be detected by PERD with error in detection remaining almost constant achieving a percentage error within a threshold of 10%$10\%$ with increase in communication range. Results also show that a faulty sensor can be detected with an average accuracy of 94%$94\%$ and it increases with increase in node density.     

NodeWiz: Fault-tolerant grid information service

Large scale grid computing systems may provide multitudinous services, from different providers, whose quality of service will vary. Moreover, services are deployed and undeployed in the grid with no central coordination. Thus, to find out the most suitable service to fulfill their needs, or to find the most suitable set of resources on which to deploy their services, grid users must resort to a Grid Information Service (GIS). This service allows users to submit rich queries that are normally composed of multiple attributes and range operations. The ability to efficiently execute complex searches in a scalable and reliable way is a key challenge for current GIS designs. Scalability issues are normally dealt with by using peer-to-peer technologies. However, the more reliable peer-to-peer approaches do not cater for rich queries in a natural way. On the other hand, approaches that can easily support these rich queries are less robust in the presence of failures. In this paper we present the design of NodeWiz, a GIS that allows multi-attribute range queries to be performed efficiently in a distributed manner, while maintaining load balance and resilience to failures.     

Rethinking the comparison of borderline personality disorder and multiple personality disorder

This article has made a number of points that assert what is today a minority position within the fields of MPD/DID and BPD. We hope our views will stimulate attempts by others to rethink their positions and test our assertions, so that issues surrounding these two disorders can be sharpened. For the sake of the clarity of future work, we summarize in outline form the essence of our viewpoint. 1. BPD and MPD/DID have similar appearing symptoms, such as identity problems, unstable affect modulation, self-destructive behaviors, chaotic impulse control, and troubled interpersonal relationships, but they have decisive differences in underlying dynamics, process, and structure. 2. DSM tends to blur these two disorders by its emphasis on phenomenology over inner structure, thus fostering misleading conclusions when DSM criteria are used to test for comorbidity or overlap between BPD and MPD/DID. 3. BPD and MPD/DID are both described dynamically as using the defense of splitting, but we contend that the splitting in each disorder is fundamentally different from the splitting in the other. BPD uses a polarization form of splitting, whereas MPD/DID uses ego splitting or identity division. 4. Both disorders partake in the process of dissociation, but the quality of dissociation in BPD is a "low-tech" spaced out type, whereas that of MPD/DID is a "high-tech" waking dream. 5. BPD structure is also "low tech," with polarization of self, object, and relationship. MPD/DID structure is "high tech," with heavily symbolic, highly nuanced variations of self, object, and relationship. 6. Although both conditions have etiologic elements of trauma, BPD has a larger degree of developmental deficiency, with a failure to complete the task of entering a repression hierarchy of defenses. MPD/DID, by use of primary process-linked symbolic dissociation, is able to continue development to the repression hierarchy, although at a profound cost of simultaneous suspension of reality testing. BPD patients suffer from the rigid use of too few defenses; MPD/DID patients suffer from the obsolete use of too many defenses. 7. BPD patients grow up in homes in which overtly expressed aggression is more tolerated, or at least more openly experienced. MPD/DID patients grow up in homes in which the fact of aggression is kept a secret. This has consequences for the formation of psychic structure in each disorder.(ABSTRACT TRUNCATED AT 400 WORDS)