Intel SoC处理器的I~2C总线IP核设计与应用

Intel SoC处理器E6x5C系列产品,作为多芯片的封装芯片,具有出色的灵活性。本文基于该处理器,利用Altera新一代集成开发工具Qsys,描述了I2 C总线IP核的设计过程,给出了IP核的系统接口和各个子模块的设计方法,并进行仿真和验证,最后将该IP核应用于模拟视频解码芯片SAA7113的配置及初始化。     

1-甲基-3-(7-氟-4-炔丙基-1,4-苯并噁嗪-3-酮-6-基)-1,3-喹唑啉-2,4-二酮的合成及其除草活性

标题化合物(SYP-298)是沈阳化工研究院的试验除草剂,由邻硝基苯甲酸经5步反应制得。其结构经核磁共振谱和质谱分析确证。SYP-298在温室条件下38 g a.i./hm2可防多种阔叶杂草,在600 g a.i./hm2对玉米和水稻安全。     

浅谈校园网大规模移动自组的网络安全技术

随着社会经济与科技的迅速发展,移动通信技术与人们生活及工作之间的联系越发紧密,移动通信技术也得到其应有的发展.在整个环境背景下,移动自组网络技术也开始出现于人们的生活中.移动自组网络技术开始应用于如军事、医疗以及电子商务等多个领域,在校园网中的应用也较为广泛.文章首先对移动自组网络进行了阐述说明,之后对校园网移动自组网络安全技术进行了深入的分析研究,以此提升人们对校园网大规模移动自组网络安全技术的认识.     

Study of the miscibility and crystallization behavior of poly(ethylene oxide)/poly(vinyl alcohol) blends

The miscibility and crystallization behavior of poly(ethylene oxide)/poly(vinyl alcohol) (PEO/PVA) blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and polarizing optical microscopy. Because the glass‐transition temperature of PVA was near the melting point of PEO crystalline, an uncommon DSC procedure was used to determine the glass‐transition temperature of the PVA‐rich phase. From the DSC and DMA results, two glass‐transition temperatures, which corresponded to the PEO‐rich phase and the PVA‐rich phase, were observed. It was an important criterion to indicate that a blend was immiscible. It was also found that the preparation method of samples influenced the morphology and crystallization behaviors of PEO/PVA blends. The domain size of the disperse phase (PVA‐rich) for the solution‐cast blends was much larger than that for the coprecipitated blends. The crystallinity, spherulitic morphology, and isothermal crystallization behavior of PEO in the solution‐cast blends were similar to those of the neat PEO. On the contrary, these properties in the coprecipitated blends were different from those of the neat PEO. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1562–1568, 2004     

酯对钼系Ziegler-Natta催化剂引发丁二烯聚合的影响

以MoCl_4(Mo)为主催化剂,甲苯氧基二异丁基铝(Al)为助催化剂,在加氢汽油溶剂中,研究了8种酯对丁二烯(Bd)聚合的影响。结果表明,凡是能够溶解在酯中的Mo与Al所组成的二元催化体系,大多能很好地引发Bd聚合,并有较高的催化活性。酯的主要作用是增加Mo在加氢汽油中的溶解性,对聚合物的分子量影响不大,对微观结构几乎无影响。     

浸没循环撞击流反应器制备牙膏用磷酸氢钙

采用浸没循环撞击流反应器（SCISR），以焦磷酸钠和磷酸三镁为稳定剂，以磷钙液和石灰乳为原料，通过中和反应法制备出了平均粒度10μm的牙膏用微细磷酸氢钙；探讨了反应温度、熟化时间、反应器装填系数、反应终点pH、磷钙液质量浓度等对产品质量的影响。确定了最优操作条件：磷钙液质量浓度1．17～1．19kg／m^3，反应温度42℃，熟化时间2h，反应终点pH6．3，反应器装填系数0．75。得到产品符合HG3257—2001标准。     

酚醛泡沫夹芯板甲醛释放与检测初步探讨

对酚醛泡沫夹芯板中甲醛的来源、释放的影响因素以及控制方法进行了初步探讨。介绍了国内外关于人造板甲醛释放量的相关规定。根据材料的特点及甲醛释放情况,采用40L干燥器法进行了甲醛检测,并进行了讨论。结果表明:与仲裁检测法———1m3气候箱法相比较,该检测方法的结果偏差很小,当取置信水平为0.95时,检测结果的变异系数均小于10%,重现性好。     

加成型液体乙烯基硅橡胶的研制Ⅱ.白炭黑表面处理对硅橡胶性能的影响

以六甲基二硅氮烷为主要表面处理剂，考察了表面处理剂、处理助剂、水的用量等对白炭黑增强效果的影响。结果表明，处理100份白炭黑时，用25份六甲基二硅氮烷，5份二甲基二乙氧基硅烷，5份水，所得白炭黑对加成型液体硅橡胶增强效果较好。     

乙烯收率状况分析与对策

通过对广州石化乙烯厂裂解原料、收率、运行状况进行分析，揭示石脑油质量波动对乙烯收率的影响，研究了乙烯收率的偏低原因，并提出原料频繁变化条件下，原料优化运作和COT调整对策。     

Preparation of HDPE/SEBS‐g‐MAH and its effect on mechanical properties of HDPE/wood flour composites

In this article, high density polyethylene/styrene‐ethylene‐butylene‐styrene block copolymer blends (HDPE/SEBS) grafted by maleic anhydride (HDPE/SEBS‐g‐MAH), which is an effective compatibilizer for HDPE/wood flour composites was prepared by means of torque rheometer with different contents of maleic anhydride (MAH). The experimental results indicated that MAH indeed grafted on HDPE/SEBS by FTIR analysis and the torque increased with increasing the content of maleic anhydride and dicumyl peroxide (DCP). Styrene may increase the graft reaction rate of MAH and HDPE/SEBS. When HDPE/SEBS MAH was added to HDPE/wood flour composites, tensile strength and flexural strength of composites can reach 25.9 and 34.8 MPa in comparison of 16.5 and 23.8 MPa (without HDPE/SEBS‐g‐MAH), increasing by 157 and 146%, respectively. Due to incorporation of thermoplastic elastomer in HDPE/SEBS‐g‐MAH, the Notched Izod impact strength reached 5.08 kJ m^?2, increasing by 145% in comparison of system without compatibilizer. That HDPE/SEBS‐g‐MAH improved the compatibility was also conformed by dynamic mechanical measurement. Scanning electron micrographs provided evidence for strong adhesion between wood flour and HDPE matrix with addition of HDPE/SEBS‐g‐MAH. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007