Strengthening of concrete prisms using the plate-bonding technique

This paper presents the use of fracture mechanics for the plate bonding technique. Plates of steel or carbon-fibre reinforced plastic are bonded with an epoxy adhesive to rectangular concrete prisms and loaded in shear up to failure, what is normally known in fracture mechanics as mode II failure. In this special application a linear and a nonlinear approach are presented. The nonlinear equation derived for a realistic shear-deformation curve can only be used for numerical calculations. However, for simplified shear-deformation curves, the derived formula can be solved analytically. Results from tests, which are compared with the theory, are also presented.     

Removal of nitrates from groundwater through the use of artificial wetlands

Intensive fertilizer use has led to nitrate contamination of groundwater in many areas. This article examines the possibility of removing nitrates through the construction of artificial wetlands. A pilot study conducted in Denmark has found that the method is effective and economical, at least for small waterworks, though further treatment is necessary before an acceptable microbiological water quality is attained.     

Buchbesprechungen

Ohne Zusammenfassung     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

Making polyurethane foams from microemulsions

A remarkable correlation exists between the degree of expansion of polyurethane foams and the structure of the reacting premixes. Polyurethane foams obtained from reacting premixes containing microemulsions are highly expanded. The expansion rate is proportional to the volume fraction of microemulsion in the premix. The stability of premixes with and without microemulsion is completely different suggesting distinct creaming mechanisms. We apply this idea to synthesize polyurethane foams from microemulsions successfully. This approach can be used to rationalize the design of polyurethane formulations leading to highly expanded foams.     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.