Defining Yield from Bender Element Measurements in Triaxial Stress Probe Experiments

This paper describes the elastic response of a block sample of compressible Chicago glacial clay under a variety of stresses and its relationship with the deformation characteristics at relatively large strains. The elastic shear stiffness was obtained from bender element tests during consolidation and shearing in drained triaxial stress probe tests. An empirical correlation was established based on the elastic shear stiffness in a preyield condition. By comparing the empirical correlation with the measured elastic shear stiffness in the stress region during probing, the changes of elastic shear stiffness were investigated. The departure of elastic shear stiffness from values computed by the empirical relation based on K0 loading directly relates to the yielding characteristics of the clay. The large-scale change of soil structure at yielding alters the well-established relationship between the elastic shear stiffness and stresses in the preyield condition. The mechanical yielding response of clays can be detected based on the systematic analysis of the elastic shear wave velocities.     

A 0.25-/spl mu/m CMOS quad-band GSM RF transceiver using an efficient LO frequency plan

This paper describes a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS applications. It is the most important design issue to maximize resource sharing and reuse in designing the multiband transceivers. In particular, reducing the number of voltage-controlled oscillators (VCOs) required for local oscillator (LO) frequency generation is very important because the VCO and phase-locked loop (PLL) circuits occupy a relatively large area. We propose a quad-band GSM transceiver architecture that employs a direct conversion receiver and an offset PLL transmitter, which requires only one VCO/PLL to generate LO signals by using an efficient LO frequency plan. In the receive path, four separate LNAs are used for each band, and two down-conversion mixers are used, one for the low bands (850/900 MHz) and the other for the high bands (1800/1900 MHz). A receiver baseband circuit is shared for all four bands because all of their channel spaces are the same. In the transmit path, most of the building blocks of the offset PLL, including a TX VCO and IF filters, are integrated. The quad-band GSM transceiver that was implemented in 0.25-/spl mu/m CMOS technology has a size of 3.3/spl times/3.2 mm/sup 2/, including its pad area. From the experimental results, we found that the receiver provides a maximum noise figure of 2.9 dB and a minimum IIP3 of -13.2dBm for the EGSM 900 band. The transmitter shows an rms phase error of 1.4/spl deg/ and meets the GSM spectral mask specification. The prototype chip consumes 56 and 58 mA at 2.8 V in the RX and TX modes, respectively.     

Mutational analysis of the three cysteines and active-site aspartic acid 103 of ketosteroid isomerase from Pseudomonas putida biotype B

In order to clarify the roles of three cysteines in ketosteroid isomerase (KSI) from Pseudomonas putida biotype B, each of the cysteine residues has been changed to a serine residue (C69S, C81S, and C97S) by site-directed mutagenesis. All cysteine mutations caused only a slight decrease in the k(cat) value, with no significant change of Km for the substrate. Even modification of the sulfhydryl group with 5,5'-dithiobis(2-nitrobenzoic acid) has almost no effect on enzyme activity. These results demonstrate that none of the cysteines in the KSI from P. putida is critical for catalytic activity, contrary to the previous identification of a cysteine in an active-site-directed photoinactivation study of KSI. Based on the three-dimensional structures of KSIs with and without dienolate intermediate analog equilenin, as determined by X-ray crystallography at high resolution, Asp-103 was found to be located within the range of the hydrogen bond to the equilenin. To assess the role of Asp-103 in catalysis, Asp-103 has been replaced with either asparagine (D103N) or alanine (D103A) by site-directed mutagenesis. For D103A mutant KSI there was a significant decrease in the k(cat) value: the k(cat) of the mutant was 85-fold lower than that of the wild-type enzyme; however, for the D103N mutant, which retained some hydrogen bonding capability, there was a minor decrease in the k(cat) value. These findings support the idea that aspartic acid 103 in the active site is an essential catalytic residue involved in catalysis by hydrogen bonding to the dienolate intermediate.     

Optical imaging of anatomical maps derived from magnetic resonanceimages using time-independent optical sources

Presents a model suitable for computing images of absorption cross sections of thick tissue structures illuminated at near infrared (NIR) wavelengths from tomographic projection data. Image reconstruction is accomplished by solving a system of linear equations derived from transport theory. Reconstruction results using different algebraic solvers are shown for anatomical maps of the breast, derived from magnetic resonance imaging data, containing two simulated pathologies, in which case qualitatively good reconstructions were obtained. Evaluation of magnetic resonance (MR) data to optimize NIR optical tomographic imaging methods and to assess the feasibility of a combined MR-optical measurement scheme is discussed     

Multiterminal light-emitting logic device electricallyreprogrammable between OR and NAND functions

A monolithic multiterminal logic device that functions both optically and electrically as an ORNAND gate, is demonstrated for the first time. The device, based on the real-space transfer of hot electrons into a complementary collector layer, has been implemented in an InGaAs/InAlAs/InGaAs heterostructure grown by molecular beam epitaxy. Excellent performance is obtained at room temperature. The collector current and the optical output power both exhibit the OR and the NAND functions of any two of the three input terminals, these functions being interchangeable by the voltage on the third terminal     

Physiological actions of the neuropeptide Antho-RNamide on antagonistic muscle systems in sea anemones

Several studies have reported that the bulk aluminum (Al) concentration is increased in the brain in Alzheimer disease (AD), while other studies have failed to demonstrate an increase. Most of these investigations have had one or more methodological deficiencies, including lack of adequate neuropathological assessment; failure to age-match the control samples; small sample sizes, lacking statistical power; and geographical heterogeneity in the AD and control populations. The present population-based study of 92 clinically and histopathologically diagnosed AD patients and normal elderly nursing home residents was designed to avoid these potential biases. When a subsample of AD cases with the most severe brain pathology was compared with controls having no or minimal pathology, no statistically significant differences were found in the bulk aluminum concentration measured by graphite furnace atomic absorption spectrometry in frontal cortex (1.8 +/- 0.7 vs. 1.7 +/- 0.7 micrograms/g dry wt), temporal cortex (1.4 +/- 0.3 vs. 1.5 +/- 0.5 micrograms/g dry wt), liver (2.0 +/- 1.3 vs. 2.0 +/- 1.2 micrograms/g dry wt), or head of femur (2.4 +/- 1.6 vs. 2.2 +/- 1.0 micrograms/g ash wt). Within the whole series of 92 cases, there was no difference in the bulk aluminum concentration of the frontal cortex between individuals diagnosed as definite, probable, and possible cases of AD using the CERAD (Consortium to Establish a Registry for Alzheimer's Disease) criteria. The density of senile plaques and neurofibrillary tangles in frontal and temporal cortex showed no correlation with the bulk aluminum concentration. Logistic regression analyses, which controlled for age and sex, did not influence outcome for any of the comparisons. The data show conclusively that in AD, bulk aluminum concentration is not increased in two cortical brain regions that are selectively vulnerable to the neuropathological changes associated with this disorder.     

Structure and surface properties of diaminocyclohexane plasma polymer films

Plasma polymers of three isomers of diaminocyclohexane (DACH) were deposited on polyethylene, SiO₂, and mica at 20°C. The deposition rate was measured as a function of plasma density and power; a maximum was observed in the latter function. The deposition rate was highest for the monomer with the highest flow rate. The film refractive index was observed to increase with both power density and the degree of fragmentation in the plasma. Film composition was measured by elementary analysis, and was found to be almost identical for each of the three isomers; a mechanism for the polymerization reaction is proposed. The percentage of primary amino groups decreased with increasing power density and with film thickness. Surface force measurements of the thickness and refractive index agreed well with the corresponding ellipsometry values in dry air, and am adhesive force, independent of power density, was measured. When the film was exposed to water vapor, it swelled considerably and the adhesion was determined by capillary forces. Associated with swelling, at high power, was an extremely regular 2-ply rope pattern of protruding material. © 1993 John Wiley & Sons. Inc.     

The crystal structure of an Fe-superoxide dismutase from the hyperthermophile Aquifex pyrophilus at 1.9 A resolution: structural basis for thermostability

The incidence of stress fractures is increasing among competitive and recreational athletes as well as among children and the elderly. By understanding the continuum of bone's response to stress and maintaining an appropriate index of suspicion, the health care provider can diagnose these injuries appropriately. An accurate history and examination is essential and will differentiate stress fractures from other stress reactions. The more common stress fractures are discussed.     

Laser scanning path generation considering photopolymer solidification in micro-stereolithography

It is essential to automate the scanning path generation process to effectively implement the micro-stereolithography. However, a scanning path that is generated based only on a 3D CAD model introduces dimensional inaccuracies. In micro-stereolithography, the photopolymer solidification is affected by fabrication conditions, such as the optical properties (laser power, laser scanning speed, laser scanning pitch focusing condition, etc.) and material properties of the photopolymer. Thus, the photopolymer solidification phenomena must be considered when generating a laser scanning path. In this paper, a scanning path generation algorithm that uses 3D CAD data and considers the photopolymer solidification phenomena is proposed to improve the dimensional accuracy in micro-stereolithography. Multi-line photopolymer solidification experiments were performed for various laser scanning conditions to examine the photopolymer solidification phenomena. From these experiments, linear relations between the solidification length (width) and scanning length (width) were acquired and stored in a database. Subsequently, these data were utilized to compensate the scanning path of the laser beam. In addition, experiments for determining the layer thickness in the z-direction were performed and these results were also used in the scanning path generation algorithm.This research was supported by the Highly Advanced National Project (http://www.most.go.kr), which performs some of the National R&D Program, and sponsored by the Korean Ministry of Science and Technology under the contract project code M10214000116-02B1500-02010.     

Design,Implementation, and Validation of KOMPSAT‐2 Software Simulator

In this paper, we present design features, implementation, and validation of a satellite simulator subsystem for the Korea Multi‐Purpose Satellite‐2 (KOMPSAT‐2). The satellite simulator subsystem is implemented on a personal computer to minimize costs and trouble on embedding onboard flight software into the simulator. An object‐oriented design methodology is employed to maximize software reusability. Also, instead of a high‐cost commercial database, XML is used for the manipulation of spacecraft characteristics data, telecommand, telemetry, and simulation data. The KOMPSAT‐2 satellite simulator subsystem is validated by various simulations for autonomous onboard launch and early orbit phase operations, anomaly operation, and science fine mode operation. It is also officially verified by successfully passing various tests such as the satellite simulator subsystem test, mission control element system integration test, interface test, site installation test, and acceptance test.