Binary blends of nylons with ethylene vinyl alcohol copolymers: Morphological,thermal, rheological,and mechanical behavior

Binary blends of ethylene vinyl alcohol copolymers, containing 62 (EVOH-62) and 71 (EVOH-71) mole percent vinyl alcohols, with nylons (nylon-6, nylon-6/12, and nylon-12) have been prepared from melt mixing in a twin screw compounding machine. Morphological, thermal, rheological, and mechanical properties were determined. EVOH-62/nylon-6 and EVOH-71/nylon-6 blends showed homogeneous phase morphologies in the nylon-6-rich region, and fine phase separations (c.a. 2 × 10^?7 m) in the EVOH-rich region. Melting point depression, positive deviations in viscosity and flexural modulus, and negative deviation in impact strength from the simple additive rule were generally observed. And the results were possibly interpreted in terms of compatibility and increased nylon/EVOH interactions over the nylon/nylon interactions. On the contrary, clean phase separations in large domains were observed from EVOH-71/nylon-6/12 and EVOH-71 /nylon-12 blends. Fibrillation was also obtained from EVOH rich blends. Probably due to the incompatible nature of these blends, yield at low rate of shear and a mechanical property drop were also observed.     

Conceptual and basic designs of the Mobile Harbor crane based on topology and shape optimization

The Mobile Harbor (MH) has been recently proposed as a novel maritime cargo transfer system that can move to a container ship anchored in the deep sea and handle containers directly at sea with the aid of a stabilized MH crane. Because this system operates under at-sea conditions, the MH crane must be designed to support an inertia load and wind force, as well as its self-weight. The wave-induced motions of the MH, e.g. rolling, pitching, and heaving, generate a significant amount of inertia load, which has not been considered in the design of conventional quayside cranes installed on stable ground. Wind force is also a critical design factor due to the higher wind velocity in the open sea. In addition to the aforementioned structural rigidity, mass minimization is also important in the structural design of MH cranes because it reduces the overturning moment and therefore enhances ship stability. In this paper, the sensitivities of the design-dependent loads (i.e. self-weight, inertia load, and wind force) are derived with respect to the design variables, and then a topology optimization is conducted with the derived sensitivities in order to obtain a conceptual design. Then, the conceptual design is elaborated into a three-dimensional basic design through shape optimization with design regulations for offshore cranes. Through the integrated design process with the topology and shape optimizations, a conceptual and basic design is successfully obtained for the MH crane.     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Dynamic light scattering measurements on the polystyrene/ethyl acetate system at semi-dilute concentrations as a function of temperature

Summary Measurements of autocorrelation functions extending over a broad time range are reported for a sample of polystyrene in ethyl acetate as a function of temperature between –44°C (-temperature) and 70°C. The corresponding spectra of decay times are obtained by two mathematical methods. The existence of three dynamic processes is shown and their temperature and angular behaviour is studied.     

Temperature-dependent transparency of poly(HPMA-co-DMA) hydrogels: effect of synthesis parameters

The acrylic comonomers hydroxypropyl methacrylate (HPMA) and N,N-dimethylaminoethyl methacrylate (DMA) have been used in several earlier studies to produce pH-responsive hydrogels. However, these same monomers can also be used to prepare hydrogels that are highly responsive to temperature. One manifestation of this temperature sensitivity is a sharp decrease in hydrogel optical transparency that occurs when the temperature exceeds a critical transition value. For example, a hydrogel that exhibits a swelling transition at the physiological pH value of 7.4 has a transition temperature of about 45 °C when the environmental salt concentration is 0.15 M. The value of the transparency transition temperature is shown to depend on hydrogel synthesis parameters such as comonomer mole ratio, crosslinker mole ratio, and even initiator concentration. By reducing the mole ratio of the crosslinker tetraethylene glycol dimethacrylate (TEGDMA), the transition temperature can be lowered by as much as 15 °C. Environmental salt concentration and solvent polarity are also shown to influence the transition temperature.     

Synthesis and luminescence properties of new blue‐light‐emitting polyconjugated poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene} polymers and copolymers

Three new soluble polyconjugated polymers, all of which emitted blue light in photoluminescence and electroluminescence, were synthesized, and their luminescence properties were studied. The polymers were poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene}, poly((9,9‐dioctylfluorene‐2,7‐diyl)‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)vinylene‐1,4‐phenylene]}) [P(DOF‐PVP)], and poly([N‐(2‐ethyl) hexylcarbazole‐3,6‐diyl]‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)]vinylene‐1,4‐phenylene}). The last two polymers had alternating sequences of the two structural units. Among the three polymers, P(DOF‐PVP) performed best in the light‐emitting diode devices of indium–tin oxide/poly(ethylenedioxythiophene) doped with poly(styrene sulfonate) (30 nm)/polymer (150 nm)/Li:Al (100 nm). This might have been correlated with the balance in and magnitude of the mobility of the charge carriers, that is, positive holes and electrons, and also the electronic structure, that is, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels, of the polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 307–317, 2006     

Influence of mixing cycle on the degree of mixing of calcite‐filled polyethylene upon stretching

The mixing cycle‐dependent degree of dispersion and degree of mixing of a calcite (calcium carbonate) agglomerate in high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), and linear low‐density polyethylene (LLDPE) matrices upon stretching was investigated using three different techniques: mechanical property, morphological behavior, and image analyzer analyses. The mechanical properties analyzed in terms of the tensile strength and maximum elongation resulted in that the second mixing was the best for giving a better property for all systems except the LDPE system, which exhibited no significant difference between the second and third mixings. The morphological behavior of the three compounds were different, but no distinctive difference was observed to differentiate the degree of mixing from system to system. The number‐, weight‐, and z + 1‐average diameters of the air hole and the aspect ratio upon the stretching and mixing cycle were calculated to analyze the degree of mixing of the calcite‐filled composites. As a consequence, no difference in the average diameter of the air hole was obtained among the three systems, but the aspect ratios of the air hole varied significantly. Thus, the degree of dispersion and the degree of mixing may be influenced by the average calcite agglomerate size, the average diameter of the air hole, and the aspect ratio upon stretching and mixing cycles. Those factors would be formed by the difference in chemical characteristics upon various microstructures of polyethylene and its molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 311–321, 2003     

Effect of low molecular weight polybutadiene as processing aid on properties of silica‐filled styrene–butadiene rubber compounds

Because silica has strong filler–filler interactions, a silica‐filled rubber compound shows a poor filler dispersion compared to a carbon black‐filled one. Improvement of the filler dispersion in silica‐filled styrene–butadiene rubber (SBR) compounds was studied using low molecular weight polybutadiene (liquid PBD) with the high content of 1,2‐unit. By adding the liquid PBD to the silica‐filled SBR compound, the filler dispersion and flow property are improved. The cure time and cure rate become faster as the 1,2‐unit content of the liquid PBD increases for the compounds containing the liquid PBD. The crosslink density increases linearly with increase in the 1,2‐unit content of the liquid PBD. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3135–3140, 2003     

The onset of Taylor-Görtler vortices in impulsively decelerating swirl flow

The onset of hydrodynamical instability induced by impulsive spin-down to rest in a cylinder containing a Newtonian fluid is analyzed by using propagation theory. It is well-known that the primary transient swirl flow is laminar, but with initial high velocities secondary motion sets in at a certain time. The dimensionless critical time Τ_c to mark the onset of instability is presented here as a function of the Reynolds number Re. Available experimental data indicate that for large Re deviation of the velocity profiles from their momentum diffusion occurs starting from a certain time Τ≈4Τ_c. This means that secondary motion is detected at this characteristic time. It seems evident that during Τ_c⪯Τ⪯4Τ_c, secondary motion is relatively very weak and the primary diffusive momentum transfer is dominant.     

Reactivity,chemical structure,and molecular mobility of urea–formaldehyde adhesives synthesized under different conditions using FTIR and solid‐state 13C CP/MAS NMR spectroscopy

This study was conducted to investigate the effects of reaction pH condition and hardener type on the reactivity, chemical structure, and molecular mobility of urea–formaldehyde (UF) resins. Three different reaction pH conditions, such as alkaline (7.5), weak acid (4.5), and strong acid (1.0), were used to synthesize UF resins, which were cured by adding four different hardeners (ammonium chloride, ammonium sulfate, ammonium citrate, and zinc nitrate) to measure gel time as the reactivity. FTIR and ¹³C‐NMR spectroscopies were used to study the chemical structure of the resin prepared under three different reaction pH conditions. The gel time of UF resins decreased with an increase in the amount of ammonium chloride, ammonium sulfate, and ammonium citrate added in the resins, whereas the gel time increased when zinc nitrate was added. Both FTIR and ¹³C‐NMR spectroscopies showed that the strong reaction pH condition produced uronic structures in UF resin, whereas both alkaline and weak‐acid conditions produced quite similar chemical species in the resins. The proton rotating‐frame spin–lattice relaxation time (T_1ρH) decreased with a decrease in the reaction pH of UF resin. This result indicates that the molecular mobility of UF resin increases with a decrease in the reaction pH used during its synthesis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2677–2687, 2003