Investigation on replication of microfluidic channels by hot embossing

In this study, effects of embossing temperature, time, and force on production of a microfluidic device were investigated. Polymethyl methacrylate (PMMA) substrates were hot embossed by using a micromilled aluminum mold. The process parameters were altered to observe the variation of replication rate in width and depth as well as symmetry of the replicated microfluidic channels. Analysis of variance (ANOVA) on the experimental results indicated that embossing temperature was the most important process parameter, whereas embossing time and force have less impact. One distinguishing aspect of this study is that, the channels were observed to be skewed to either side of the channel depending on the location of the protrusions on the mold. The mechanism of the skewness was investigated by finite element analysis and discussed in detail. Results showed that the skewness depends on the flow characteristics of the material and could be reduced by increasing the embossing temperature. The best replication rates were obtained at parameter settings of 115°C, 10?kN, and 8?min for the molds with minimum 56?µm wide features of 120?µm depth. We also showed that the fabricated channels could be successfully sealed by solvent-assisted thermo-compressive bonding at 85°C under 5.5?kN force.     

Electrical and Dielectric Properties of Y<Superscript>3+</Superscript>-Substituted Barium Hexaferrites

In this study, Y³⁺ ion-substituted M-type barium hexaferrites (BaM; BaFe₁₂O₁₉) were fabricated via facile ceramic route. As-prepared powders were characterized by X-ray powder diffractometry (XRD), Fourier transform infrared (FT-IR) spectroscopy, and impedance spectroscopy. XRD (Rietveld) analyses confirmed the presence of a single characterization of all samples (except x = 0.0 and 0.1 samples). The crystallite sizes of products are found in the range of 47.2–63.2 nm. Spectral analysis (FT-IR) also presented the formation of spinel structure for all products. The ac conductivity of the substituted samples was found to initially decrease slightly with increase in Y³⁺ compared with unsubstituted, and then variation tendency changes at the medium substitution ranges are observed with a different attitude against temperature. In the end, the lower conductivity for high substitutions is recorded and increases as functions of frequency while it also increases with the elevation of temperature. It was observed that ac conductivities of products increased by increasing frequency which indicate that observed ac conductivity is due to both electronic and polaron hopping mechanism.     

Stochastic two-sided U-type assembly line balancing: a genetic algorithm approach

In this paper, a novel stochastic two-sided U-type assembly line balancing (STUALB) procedure, an algorithm based on the genetic algorithm and a heuristic priority rule-based procedure to solve STUALB problem are proposed. With this new proposed assembly line design, all advantages of both two-sided assembly lines and U-type assembly lines are combined. Due to the variability of the real-life conditions, stochastic task times are also considered in the study. The proposed approach aims to minimise the number of positions (i.e. the U-type assembly line length) as the primary objective and to minimise the number of stations (i.e. the number of operators) as a secondary objective for a given cycle time. An example problem is solved to illustrate the proposed approach. In order to evaluate the efficiency of the proposed algorithm, test problems taken from the literature are used. The experimental results show that the proposed approach performs well.     

Coping with production time variability via dynamic lead-time quotation

In this paper, we propose two dynamic lead-time quotation policies in an M/GI/1 type make-to-stock queueing system serving lead-time sensitive customers with a single type of product. Incorporating non-exponential service times in an exact method for make-to-stock queues is usually deemed difficult. Our analysis of the proposed policies is exact and requires the numerical inversion of the Laplace transform of the sojourn time of an order to be placed. The first policy assures that the long-run probability of delivering the product within the quoted lead-time is the same for all backlogged customers. The second policy is a refinement of the first which improves the profitability if customers are oversensitive to even short delays in delivery. Numerical results show that both policies perform close to the optimal policy that was characterized only for exponential service times. The new insight gained is that the worsening impact of the production time variability, which is felt significantly in systems accepting all customers by quoting zero lead times, decreases when dynamic lead-time quotation policies are employed.     

Estimating Construction Material Indices with ARIMA and Optimized NARNETs

Construction Industry operates relying on various key economic indicators. One of these indicators is material prices. On the other hand, cost is a key concern in all operations of the construction industry. In the uncertain conditions, reliable cost forecasts become an important source of information. Material cost is one of the key components of the overall cost of construction. In addition, cost overrun is a common problem in the construction industry, where nine out of ten construction projects face cost overrun. In order to carry out a successful cost management strategy and prevent cost overruns, it is very important to find reliable methods for the estimation of construction material prices. Material prices have a time dependent nature. In order to increase the foreseeability of the costs of construction materials, this study focuses on estimation of construction material indices through time series analysis. Two different types of analysis are implemented for estimation of the future values of construction material indices. The first method implemented was Autoregressive Integrated Moving Average (ARIMA), which is known to be successful in estimation of time series having a linear nature. The second method implemented was Non-Linear Autoregressive Neural Network (NARNET) which is known to be successful in modeling and estimating of series with non-linear components. The results have shown that depending on the nature of the series, both these methods can successfully and accurately estimate the future values of the indices. In addition, we found out that Optimal NARNET architectures which provide better accuracy in estimation of the series can be identified/discovered as result of grid search on NARNET hyperparameters.     

Preserving spatial information and overcoming variations in appearance for face recognition

Local feature-based approaches mainly aim to achieve robustness to variations in facial images by assuming that only some parts of the facial images may be affected. However, such approaches may lose spatial information. In this study, a compromise feature extraction scheme is studied which extracts local features while preserving spatial information. The proposed scheme exploits an ensemble of classifiers where each member is constructed using randomly selected design parameters including the size, number and location of sub-images for local feature extraction. Experiments conducted on FERET and ORL databases have shown that proposed scheme surpasses the local feature-based reference systems which focus on either local information or preserving spatial information.     

Approximation by Stancu–Chlodowsky polynomials

In this paper, we investigate convergence and approximation properties of a Chlodowsky type generalization of Stancu polynomials (we called Stancu–Chlodowsky polynomials).The rates of convergence of this generalization are obtained by means of modulus of continuity and by using the $K$-functional of Peetre. We also present and prove theorems on weighted approximation and the order of approximation of continuous functions by these operators on all positive semi-axis.     

Schauder bases and approximation property in fuzzy normed spaces

Our aim in this article is to introduce and study the notion of weak and strong Schauder bases in fuzzy normed spaces. Further, we introduce strong and weak fuzzy approximation properties and set a relationship between these two new notions which may provide an acceleration to the structural analysis of fuzzy normed spaces.