Ab-initio primitive cell parameters from single convergent-beam electron diffraction patterns: a converse route to the identification of microcrystals with electrons.

A new method for the ab initio derivation of Buerger-reduced primitive cell parameters from coordinate measurements of spots on single convergent-beam electron diffraction (CBED) patterns is described, which does not involve trial-and-error. The pattern can be taken along any zone axis, and misorientations of the crystallite by as much as a few degrees are taken into account without loss of accuracy. This derivation of cell parameters by least-squares analysis of the measurements has been automated in a program called NRCBED. Present accuracy is about 1% on lengths and 2 degrees on angles, but could be significantly improved by modelling projector lens aberrations, or by using a microscope without a projector lens. With present technology, it is possible to obtain a CBED pattern and a semi-quantitative energy-dispersive X-ray (EDX) analysis simultaneously from a single microcrystal a few hundred Angstr?ms across. It becomes therefore possible to identify the material of the crystal on a single CBED pattern: a cell parameter database for known compounds is searched with the primitive cell parameters obtained in the above way, and with a mask describing the EDX results qualitatively. Feasibility is demonstrated on a crystallite of CeO2 500 Angstr?ms across. With this new approach, trial-and-error should disappear from the solution of other long-standing problems: interpretation of X-ray powder patterns for new compounds in the presence of impurity lines, or in the case of multiple phases should become straight-forward.     

Highly integrated direct conversion receiver for GSM/GPRS/EDGE with on-chip 84-dB dynamic range continuous-time /spl Sigma//spl Delta/ ADC

This paper describes a highly digitized direct conversion receiver of a single-chip quadruple-band RF transceiver that meets GSM/GPRS and EDGE requirements. The chip uses an advanced 0.25-/spl mu/m BiCMOS technology. The I and Q on-chip fifth-order single-bit continuous-time sigma-delta (/spl Sigma//spl Delta/) ADC has 84-dB dynamic range over a total bandwidth of /spl plusmn/135 kHz for an active area of 0.4 mm/sup 2/. Hence, most of the channel filtering is realized in a CMOS IC where digital processing is achieved at a lower cost. The systematic analysis of dc offset at each stage of the design enables to perform the dc offset cancellation loop in the digital domain as well. The receiver operates at 2.7 V with a current consumption of 75 mA. A first-order substrate coupling analysis enables to optimize the floor plan strategy. As a result, the receiver has an area of 1.8 mm/sup 2/.     

Dynamics of the transient buildup of emission inNd3+-doped fiber lasers

The two-stage process of the transient buildup of emission in Nd ⁴⁺-doped fiber lasers is described both experimentally and theoretically. After switching on the pump, spontaneous emission increases first until the gain becomes sufficient to compensate for the cavity losses; the laser field then develops and reaches the steady state after more or less regular oscillations. During this second stage, an almost chaotic spiking is obtained either for high pumping rates and/or at low temperatures. The whole set of these dynamical scenarios is not described under the usual assumptions of uniform cavity losses over the whole field spectrum and of pure homogeneous broadening for the transition line, but rather a modified form of the Maxwell-Bloch equations which retains some frequency dependence for the losses in the cavity and the inhomogeneous broadening as well is proposed     

A distributed approach for access and visibility task with a manikin and a robot in a virtual reality environment

This paper presents a new method, based on a multi-agent system and on a digital mock-up technology, to assess an efficient path planner for a manikin or a robot for an access and visibility task taking into account ergonomic constraints or joint and mechanical limits. In order to solve this problem, the human operator is integrated in the process optimization to contribute to a global perception of the environment. This operator cooperates, in real time, with several automatic local elementary agents. The result of this work validates solutions through the digital mock-up; it can be applied to simulate maintainability and mountability tasks.     

Elastic properties of polycrystalline gold thin films: Simulation and X-ray diffraction experiments

The elastic behavior of supported gold thin films has been studied using a framework in which the elastic interaction between grains and the actual structure of the film (i.e. preferential grain orientation and grain shape) are taken into account. Experiments were carried out using synchrotron X-ray diffraction combined with in-situ tensile testing and thereafter, no assumptions on the residual stress state and on the stress-free lattice parameter a₀ have to be made. Modeling of grain elastic interactions is based on the extension of Eshelby-Kröner model, which allows for estimating the elastic behavior of polycrystals considering the texture and the shape of the crystallites. Flat-disc shaped grains arrangement is shown to yield the best representation of the elastic behavior of the fiber-textured gold thin films composed of columnar grains. This non-intuitive representation results from free-surface effect.     

In situ regeneration of the Ni-based catalytic reformer of a 5 kW PEMFC system

The paper reports the results of on-site regeneration catalytic bed of the natural gas reformer in a 5 kW PEM fuel cell system. The Ni catalyst previously poisoned by sulphur from the available natural gas, could be re-activated by injection of pure water steam, following the method developed for industrial reformers using the same metal catalyst: this method was shown to be perfectly efficient, provided no natural gas was fed during the operation. Results of the tests conducted are presented and discussed in relation to published data on S-sorption on Ni surfaces.     

Pinhole density measurements of barriers deposited on low-k films

Evaluation of diffusion barrier integrity is an important issue in advanced interconnects. A diffusion barrier separating Cu from low-k must be as thin as possible and must not contain pinholes. We have developed a method for measuring pinhole density in diffusion barriers deposited on low-k materials. The method employs ellipsometric porosimetry for measuring diffusion of toluene in a porous low-k film beneath the barrier in question.     

New integrated buried laser-ridge modulator with identical active layer

Integrated laser modulators are attractive devices for wavelength-division-multiplexing optical systems due to their compactness, high output power, and low cost. Their fabrication simplicity is a way to decrease further the transmitter cost and address new opening markets of short range and metropolitan networks. We report a new integration scheme electroabsorption-modulator distributed feedback (DFB) laser based on well-established industrial solutions for discrete buried ridge (BRS) DFB lasers and discrete shallow ridge modulators. Processing simplification with an identical active layer has been possible due to a good behavior of strongly positively detuned BRS lasers. The integrated devices demonstrated 30-dB extinction ratio with 10-GHz bandwidth and P/sub out/=10 dBm for emission in 1.55-/spl mu/m range.     

An investigation of carbon nanotube jet grinding

Since their observation in 1976 and 1991, carbon nanotubes (CNTs) have generated much interest due to their properties and potential applications. CNTs are tubular carbon molecules with remarkable mechanical, electrical, chemical and thermal properties, which make them useful in various applications. Industries producing CNTs via the fluidized bed chemical vapor deposition technique face challenges related to the size of CNT bundles. The two main challenges are agglomeration and agglomerate size distribution control. A solution to these challenges involves the use of jet mills to grind the CNT agglomerates. The goal of this study was to determine whether the nanotubes could be ground with air jets using a commercial jet mill and apply a two-parameter model to describe the grinding process. The present study has indicated that air-jet grinding of CNTs is feasible with a typical commercial jet mill. This paper presents the effect of operational parameters on the arithmetic mean diameter of the ground product. Sonic velocity through the grinding nozzles was required to obtain reasonable grinding rates and relatively narrow particle size distributions. This occurs at high air to solids feedrate ratios. Additionally, a simple attrition model can describe the grinding process in the spiral jet mill.     

Longitudinal analysis of the relationship between symptoms and quality of life in veterans treated for posttraumatic stress disorder.

This study examined how change in posttraumatic stress disorder (PTSD) symptoms relates to change in quality of life. The sample consisted of 325 male Vietnam veterans with chronic PTSD who participated in a randomized trial of group psychotherapy. Latent growth modeling was used to test for synchronous effects of PTSD symptom change on psychosocial and physical health-related quality of life within the same time period and lagged effects of initial PTSD symptom change on later change in quality of life. PTSD symptoms were associated with reduced quality of life before treatment. There were synchronous effects of symptom change on change in quality of life but no significant lagged effects. Results indicate the importance of measuring quality of life in future investigations of PTSD treatment. (PsycINFO Database Record (c) 2010 APA, all rights reserved)