Cohesive strength of nanocrystalline ZnO:Ga thin films deposited at room temperature

In this study, transparent conducting nanocrystalline ZnO:Ga (GZO) films were deposited by dc magnetron sputtering at room temperature on polymers (and glass for comparison). Electrical resistivities of 8.8 × 10-4 and 2.2 × 10-3 Ω cm were obtained for films deposited on glass and polymers, respectively. The crack onset strain (COS) and the cohesive strength of the coatings were investigated by means of tensile testing. The COS is similar for different GZO coatings and occurs for nominal strains approx. 1%. The cohesive strength of coatings, which was evaluated from the initial part of the crack density evolution, was found to be between 1.3 and 1.4 GPa. For these calculations, a Young's modulus of 112 GPa was used, evaluated by nanoindentation.     

The final bleaching of eucalypt kraft pulps with hydrogen peroxide: relationship with industrial ECF bleaching history and cellulose degradation

BACKGROUND: The process of chemical pulp bleaching is based for the most part in chlorine dioxide within elemental chlorine free (ECF) technologies. The use of greener alternatives such as bleaching with hydrogen peroxide (P stage) is not widely used owing to selectivity concerns related to transition metal‐catalyzed decomposition reactions. Even at the final stage where peroxide is recognized to boost brightness and improve the brightness stability of the bleached pulp, cellulose degradation often overcomes these advantages. This paper presents the results of studies intended to optimize final peroxide bleaching performance considering two standard ECF industrial bleaching sequences: the conventional DED and the ECF‐light OQ(PO)D (stages name: D—chlorine dioxide; E—alkaline extraction; O—oxygen; Q—chelation, (PO)—hydrogen peroxide pressurized with oxygen). RESULTS: The addition of sodium diethylenetriaminepentaacetate (DTPA) was the most effective option in terms of DED pulp bleachability and selectivity with hydrogen peroxide, as well as in terms of brightness reversion. As regards the OQ(PO)D pulp, a blend of DTPA and magnesium was the most beneficial in those properties. CONCLUSIONS: The choice of the best hydrogen peroxide stabilizer, among the different tested combinations of magnesium and chelants (EDTA and DTPA) studied, in terms of pulp bleachability, bleaching selectivity and brightness reversion is dependent on the impact of the previous bleaching stages on metallic nature and content. The pulp Mg/(Fe + Cu) ratio was highlighted as a process parameter controlling cellulose degradation in peroxide bleaching. Copyright © 2010 Society of Chemical Industry     

Colour assays: An inside look into Alentejo traditional limewash paintings and coloured lime mortars

A series of colour assays were conducted taking into account old bibliographic recommendations and oral testimony regarding traditional lime painting technology from the Alentejo (South Portugal) region. The main objectives were: (a) the colorimetric analysis of paintings made with different limewash preparation methods; (b) the comparison between natural processed red and yellows ochre pigments (“home made” and from industrial origin) and synthetic iron oxides in different concentrations and lime proportions; (c) the evaluation of the colorimetric CIELAB coordinates during the lime carbonation process in coloured mortars and limewashes. The results shows that the evolution of L*, a*, and b* during the carbonation process is independent of pigment concentration and paint thickness but dependent of pigment composition and finishing technique (lime painting or coloured mortar). They also emphasize the importance of surface appearance attributes and its influence on the colorimetric parameters. © 2010 Wiley Periodicals, Inc. Col Res Appl, 36, 61–71, 2011     

Two‐dimensional fluorescence as a fingerprinting tool for monitoring wastewater treatment systems

BACKGROUND: The use of two‐dimensional (2D) fluorescence for monitoring complex biological systems requires careful assessment of the effect of chemical species present, which may be fluorescent and/or may interfere with the fluorescence response of target fluorophores. Given the complexity of fluorescence data (excitation emission matrices—EEMs), the challenge is how to recover the information embedded into those EEMs that can be related quantitatively with the observed performance of the biological processes under study. RESULTS: This work shows clearly that interference effects (such as quenching and inner filter effects) occur due to the presence of multiple species in complex biological media, such as natural water matrices, wastewaters and activated sludge. A statistical multivariate analysis is proposed to recover quantitative information from 2D fluorescence data, correlating EEMs with the observed performance. A selected case study is discussed, where 2D fluorescence spectra obtained from the effluent of a membrane bioreactor were compressed using PARAFAC and successfully correlated with the effluent chemical oxygen demand, using projection to latent structures modelling. CONCLUSION: This study demonstrates the potential of using 2D fluorescence spectroscopy as a status fingerprint. Additionally, it is shown how statistical multivariate data analysis can be used to correlate EEMs with selected performance parameters for monitoring of biological systems. Copyright © 2011 Society of Chemical Industry     

Stability of viscoelastic liquid curtain

Thin liquid sheets occur in several practical applications. In curtain coating, a thin liquid sheet is formed and falls freely over a considerable height before it impinges onto a moving substrate. Precision curtain coating was developed for multi layer photographic films but its use has expanded to many different applications. One of the important limits of this process is the stability of the liquid curtain, which may define the minimal thickness that can be coated at a given web speed.The condition at which a low viscosity Newtonian liquid curtain breaks was first derived based on a simple balance between inertial and capillary forces. There is a critical flow rate below which the curtain becomes unstable. For viscoelastic liquids, the normal stress related to the stretching of polymer molecules as the liquid accelerates down the curtain changes the force balance. Here, the critical condition at which a viscoelastic liquid curtain breaks was determined as a function of the rheological properties of the liquid. The results show that high extensional viscosity liquids create more stable curtains. Liquid additives could be used to push the limits of curtain flow rates to smaller values and consequently to widen the operability window of the process.     

Solvent Influence on the Hydrodeoxygenation of Guaiacol over Pt/SiO2 and Pt/H‐MFI 90 Catalysts

Second generation biofuels are produced in the bioliq® process at the Karlsruhe Institute of Technology via gasification of pyrolysis oil and synthesis of gasoline from the emerging synthesis gas. An alternative strategy is the direct upgrading of the pyrolysis oil by hydrodeoxygenation (HDO). The present study reports on the HDO of guaiacol as one of the phenolic compounds strongly abundant in such mixtures. Special focus was laid on the solvent influence using Pt‐based catalysts. Higher HDO ability was seen using nonpolar solvents and acidic supports. Characterization of the catalysts before and after the test showed that the solvent did not only influence the reactivity, but also the catalyst stability.     

Synthetic and Biological Studies of Sesquiterpene Polygodial: Activity of 9‐Epipolygodial against Drug‐Resistant Cancer Cells

Polygodial, a terpenoid dialdehyde isolated from Polygonum hydropiper L., is a known agonist of the transient receptor potential vanilloid 1 (TRPV1). In this investigation a series of polygodial analogues were prepared and investigated for TRPV1‐agonist and anticancer activities. These experiments led to the identification of 9‐epipolygodial, which has antiproliferative potency significantly exceeding that of polygodial. 9‐Epipolygodial was found to maintain potency against apoptosis‐resistant cancer cells as well as those displaying the multidrug‐resistant (MDR) phenotype. In addition, the chemical feasibility for the previously proposed mechanism of action of polygodial, involving the formation of a Paal–Knorr pyrrole with a lysine residue on the target protein, was demonstrated by the synthesis of a stable polygodial pyrrole derivative. These studies reveal rich chemical and biological properties associated with polygodial and its direct derivatives. These compounds should inspire further work in this area aimed at the development of new pharmacological agents, or the exploration of novel mechanisms of covalent modification of biological molecules with natural products.     

Recent Advances in Lipase-Mediated Preparation of Pharmaceuticals and Their Intermediates

Biocatalysis offers an alternative approach to conventional chemical processes for the production of single-isomer chiral drugs. Lipases are one of the most used enzymes in the synthesis of enantiomerically pure intermediates. The use of this type of enzyme is mainly due to the characteristics of their regio-, chemo- and enantioselectivity in the resolution process of racemates, without the use of cofactors. Moreover, this class of enzymes has generally excellent stability in the presence of organic solvents, facilitating the solubility of the organic substrate to be modified. Further improvements and new applications have been achieved in the syntheses of biologically active compounds catalyzed by lipases. This review critically reports and discusses examples from recent literature (2007 to mid-2015), concerning the synthesis of enantiomerically pure active pharmaceutical ingredients (APIs) and their intermediates in which the key step involves the action of a lipase.     

High surface area LaNiO<Subscript>3</Subscript> electrodes for oxygen electrocatalysis in alkaline media

LaNiO₃ coatings on nickel-foam supports were prepared by brush painting. The electrochemical properties were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Comparative studies were performed with LaNiO₃-pelleted electrodes. The roughness factors were determined by CV and found to be 5,208 ± 350 and 4,037 ± 250 for the pelleted and coated electrodes, respectively. EIS measurements confirm the results obtained by CV. Values lower than 0.3 were calculated for the morphology factors for both electrodes, indicating low electrochemical porosity. The experimental method used in this work to synthesise the oxide coupled with the use of Ni foam as support has proved to be very effective in producing oxide electrodes with surface areas higher than those referred to in relevant literature.     

In situ compatibilization of a polyethylene,polypropylene, and polystyrene ternary blend through Friedel–Crafts alkylation

The Friedel–Crafts alkylation reaction has been applied to reactively compatibilize a ternary blend of high-density polyethylene (HDPE), polypropylene (PP), and polystyrene (PS). The reactions were carried out in an internal mixer using varying catalyst concentrations. The resulting compatibilizer was quantified after Soxhlet extraction. In addition, p-substitution due to the grafting of alkyl groups onto the PS benzene ring was identified via nuclear magnetic resonance spectroscopy. The size of the PS domain in the reactive compositions is decreased by 80%. Moreover, the phase in which PS droplets were dispersed varied, that is, in the nonreactive blends they were found in the PP phase and in the reactive blends they shifted toward the HDPE phase. The effect of the compatibilizing agent was to improve the mechanical properties of the blend. Even with the lowest catalyst content, the properties of elongation-at-break, tensile strength, toughness, and elastic modulus showed improvements. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48295.