Flow properties of plasticized PVC: Reduction to composition and interaction variables

Existing theory of polymer flow has been applied to a definition of shift factors which reduce the widely different melt viscosity/shear rate diagrams of plasticized PVC compounds to well-defined master curves. The master curves are temperature dependent and also define the flow properties of the unplasticized polymer on which a group of plasticized compounds is based. For given plasticizers, the value of the shift factor was found to depend on melt temperature and plasticizer volume fraction. Explicit relationships have been generated for three plasticizer systems; for these, melt viscosity/shear rate data can be precalculated over several decades of shear, and in the temperature range of 150–200°C. Absolute values of the shift factors depend on the type of plasticizer, and a correlation with polymer/diluent interaction parameters has been attempted. Initial results, valid only at high plasticizer volumes and near the reduced melt temperature of a polymer/plasticizer mixture, support the existence of such a correlation.     

Spigelian hernia

Spigelian hernia is very rare. Together with the direct inguinal hernia which emerges between the inferior epigastric artery and the edge of the rectus muscle, it is more frequent. Congenital openings in the aponeurosis of the transverse muscle permit the hernia either above or under the inferior epigastric artery. Due to neglect of this type of hernia and absence of herniation, the diagnosis can be difficult. Complaints are often uncharacteristic. Surgical intervention is indicated.     

A Two-Channel Picture Coding System: I--Real-Time Implementation

The two-channel system previously reported has been implemented in hardware using system parameters appropriate to consumer television. The basic system divides the spectrum into lowand high-frequency spatial components. The lows are coarsely sampled and finely quantized and the highs finely sampled and coarsely quantized using a companded, randomized quantizer. The purpose of this experiment was to demonstrate the potential of the system for low-cost practical application, to study the effect of the character of the randomizing noise, and to ascertain that there were no deleterious effects due to interlace, motion, or input noise. Theoretical noise calculations were qualitatively confirmed.     

Artificial apposition compound eye fabricated by micro-optics technology

By exploring micro-optical design principles and technology, we have developed an artificial apposition compound eye. The overall thickness of the imaging system is only 320 microm, the diagonal field of view is 21 degrees, and the f-number is 2.6. The monolithic device consists of an UV-replicated microlens array upon a thin silica substrate with a pinhole array in a metal layer on the back side. The pitch of the pinholes differs from that of the lens array to provide individual viewing angle for each channel. Theoretical limitations of resolution and sensitivity are discussed as well as fabrication issues and compared with experimental results. A method to generate nontransparent walls between optical channels to prevent cross talk is proposed.     

Optimized preparation of cross-sectional TEM specimens of organic thin films

We present a route for the preparation of cross-sectional TEM specimens of crystalline organic thin films which minimizes the mechanical, chemical and thermal load of the organic film during preparation and allows to take TEM images with molecular resolution. A typical example of a thin film of diindenoperylene capped with a thin layer of gold is shown to demonstrate the application of the technique for the investigation of metal-organic interfaces.     

ILC beam energy measurement based on synchrotron radiation from a magnetic spectrometer

We propose to measure, on a bunch-to-bunch basis, the beam energy at the International Linear e⁺e^- Collider by recording synchrotron radiation (SR) light emitted in the magnets of an energy spectrometer based on beam position monitors. Measuring the width of the horizontal SR fan permits to determine the relative beam energy with a precision better than 10^-4. There are two different measuring schemes possible. The first one is based on edge measurements of the direct SR fan, while the second option includes mirrors to deflect soft SR light to detectors located sufficiently off the beamline. Three possibilities for high-spatial resolution detectors are considered: a standard silicon strip detector, a novel-type Si detector and a gas amplification detector, both with exceptional position resolution. The main issue of the first scheme is the high radiation dose expected in the direct SR fan. If mirrors are used this dose is strongly reduced and allows application of any of the three detectors proposed.     

State/event fault trees—A safety analysis model for software-controlled systems

Safety models for software-controlled systems should be intuitive, compositional and have the expressive power to model both software and hardware behaviour. Moreover, they should provide quantitative results for failure or hazard probabilities. Fault trees are an accepted and intuitive model for safety analysis, but they are incapable of expressing state dependencies or temporal order of events. We propose to combine fault trees with an explicit State/Event semantics, using a graphical notation that is similar to Statecharts. Our new model, named State/Event Fault Trees (SEFTs), subsumes both deterministic state machines suited to describe software behaviour, and Markov chains that model probabilistic failures, while keeping the visualisation of causal chains known from fault trees. We allow exponentially distributed probabilistic events, deterministic delays, and triggered events. The model provides a component concept, where components are connected by typed ports. Quantitative evaluation is achieved by translating the component models to Deterministic and Stochastic Petri Nets (DSPNs) and using an existing tool for analysis or simulation. This paper, which is an extended version of [Kaiser B, Gramlich C. State-Event-Fault-Trees—a safety analysis model for software controlled systems. Computer safety, reliability, and security. Proceedings of the 23rd international conference, SAFECOMP 2004, Potsdam, Germany, September 21st–24th. Lecture Notes in Computer Science, vol. 3219, 2004.p. 195–209], revisits the model elements and the analysis procedure and provides a small case study of a fire alarm system, completed by an outlook on our tool project ESSaRel.     

Solution-induced changes in the properties of polyethylenes

The chain entanglement states in high density, linear low density, and low density polyethylenes (HDPE, LLDPE, and LDPE) have been modified by recovering the polymers from solutions in trichlorobenzene (TCB) and p-xylene. In the thermodynamically good solvent, TCB, the entanglement density is assumed to be sharply reduced, a condition which is carried over to the corresponding solids. These display transient, but large increments in tensile moduli, slight changes in stress at rupture, and decreases in dynamic mechanical parameters and in elongation at rupture. Scanning calorimetry also shows these solids to have reduced crystallinity. Much smaller property modifications are noted in corresponding samples recovered from p-xylene. This liquid is a poorer solvent, particularly for HDPE and LLDPE. The results indicate that property modifications due to deliberate changes in the entanglement states of the polymers are a general phenomenon in the polyethylenes, and the magnitude of property changes depends on parameters of the molecular weight distribution. Chain branching does not seem to be a leading factor in the sensitivity of properties to modifications in the entanglement states. The property modifications produced by the present solution treatments are viewed as guides to the magnitude and duration of shear refining effects to be expected in HDPE, LLDPE, and LDPE polymers.