低温粉碎系统中旋风分离器设计

旋风分离器是一种应用离心力进行粉体分离的设备。低温粉碎系统应用它分离粉体并起集粉作用。它的效率决定了物质回收率。本文从离心加速度与重力加速度的比值，筒体的高低，筒体直径，进口速度叙述对分离器效率的影响。着重叙述筒体直径确定方法，以及我们设计造长筒形旋风分离器的具体结构和令人满意的试验结果。     

GH2027铁基高温合金的第二相研究

运用电子显微分析和波谱分析等方法对ＧＨ２０２７合金的第二相进行了研究，结果表明，合金晶界相主要是片状Ｍ６Ｃ和薄膜状Ｍ２３Ｃ６，经波纹图样测得其错配度约为３％，晶内Ｍ６Ｃ和Ｍ２３     

碳纤维缠绕复合材料在潜水外压容器上的应用

在铝合金圆筒体外以浸渍树脂碳纤维进行缠绕复合增强，增强后的筒体耐静水外压能力大幅度提高；整体缠绕的全复合材料筒体，在耐静水外压能力及减轻自身重量方面也获得了明显的效果。此外，在铝合金细长圆管的外壁复合缠绕碳纤维，能有效地提高圆管对轴向压载荷的抗失稳与抗屈曲破坏能力。     

RADIATION FIELD FROM A RECTANGULAR PLAQUE SOURCE FOR RADIATION PROCESSING

Evaluation of the Hubbell integral for an omnidirectional detector response to a rectangular plaque gamma emitting radiation source using a different numerical computation method on a personal computer was made. For a plaque consisting of several strip gamma emitters, exposure rates at different positions above the source were calculated using 'exact' evaluation and an approximate method. Optimization method is used to find source activity of each strip, so as to acquire desirable dose uniformity of the irradiated products. In uses of the Hubbell integral, by introducing appropriate programming, computation time can be saved.     

江苏省本地电话网结构与发展

分片汇接的网状网结构是江苏省本地电话网的基本框架,而汇接局和连接汇接局的传输系统则是网路规划与通信建设的重点。     

Simulation of the pressure set-point change transient with the Kuosheng plant analyzer

The purpose of this paper is to simulate the pressure set-point change transient with the Kuosheng plant analyzer. The Kuosheng plant analyzer was developed for the Kuosheng nuclear power station based on the boiling water reactor plant analyzer of the Brookhaven National Laboratory and the Chinshan plant analyzer of the Taiwan Power Co. First, the pressure control system (PCS) model was verified on a stand-alone basis, with the sensed dome pressure test signal as the input variable. Then, a transient induced by a step change in the pressure set-point was simulated with the Kuosheng plant analyzer and compared with the test data. The predicted results of the main system variables showed good agreement with the test data-within 8% of the maximum relative deviation. In addition, the PCS performance of the Kuosheng nuclear power station was analyzed.     

稀土变质剂对铸造铝合金性能的影响

采用正变试验法，探讨了稀土变质剂对铸造结合金ZL102性能提高的可行性．试验选用了不同的稀土添加量，考察了不同的变质时间及热处理制度对ZL102的强度、硬度、流动性以及重熔性等性能的综合影响规律．试验表明，稀土是铸造铝合金的优良变质剂，并且添加单一稀土的变质效果优于混合稀土．     

空间工程辅助设计GIS系统的研究与实践

探讨GIS技术在空间工程辅助设计(例如电力、电信管线工程)方面的应用.在系统分析空间工程设计的 逻辑过程和工程辅助设计系统的发展与需求的基础上,对GIS技术在空间工程辅助设计中应用的优势及工程辅助 设计GIS系统的结构、功能和特点以及系统基本设计思路进行了探讨，指出GIS技术的引入一方面提高了空间工 程辅助设计的效率和水平，同时使空间工程辅助设计成为同时具有规划和设计功能的系统。     

Multiple respiratory gas monitoring causes changes of inspired oxygen concentration in closed anesthesia system

This case report describes an accessory hepatic duct (AHD) identified by intraoperative cholangiography during excisional surgery of a choledochal cyst (CC). The accessory duct was divided and reconstructed successfully to the Roux-en-Y jejunal loop. The postoperative course was uneventful, and follow-up abdominal sonography revealed neither evidence of biliary tract obstruction nor atrophic changes of the liver. It is advocated that an AHD should be meticulously reconstructed if it is divided during excisional surgery of a CC.     

钻杆接头螺纹退刀尺寸对接头寿命的影响

钻杆接头螺纹退刀尺寸是指外螺纹接头的台肩面到螺纹消失前第一个完整螺纹之间的距离。GB9253．1－88规定退刀尺寸应小于或等于12．7mm内螺纹，钻杆接头内螺纹的锤孔尺寸为16±2mm，以保证内、外螺纹啮合良好。经检测发现，从日本NKK公司进口的所有φ127mm钻杆接头外螺纹退刀尺寸都大于12．7mm，镗孔尺寸为16～18mm。而APISpec7K规定钻杆接头内螺纹最小镗孔尺寸为15．9mm。鉴于此，建议对我国的有关标准作相应修改，与API标准保持一致。