On the design of multiple key hashing files for concurrent orthogonal range retrieval between two disks

This paper concerns the following problem: given a set of multi-attribute records, a fixed number of buckets and a two-disk system, arrange the records into the buckets and then store the buckets between the disks in such a way that, over all possible orthogonal range queries (ORQs), the disk access concurrency is maximized. We shall adopt the multiple key hashing (MKH) method for arranging records into buckets and use the disk modulo (DM) allocation method for storing buckets onto disks. Since the DM allocation method has been shown to be superior to any other allocation methods for allocating an MKH file onto a two-disk system for answering ORQs, the real issue is knowing how to determine an optimal way for organizing the records into buckets based upon the MKH concept.

A performance formula that can be used to evaluate the average response time, over all possible ORQs, of an MKH file in a two-disk system using the DM allocation method is first presented. Based upon this formula, it is shown that our design problem is related to a notoriously difficult problem, namely the Prime Number Problem. Then a performance lower bound and an efficient algorithm for designing optimal MKH files in certain cases are presented. It is pointed out that in some cases the optimal MKH file for ORQs in a two-disk system using the DM allocation method is identical to the optimal MKH file for ORQs in a single-disk system and the optimal average response time in a two-disk system is slightly greater than one half of that in a single-disk system.     

Parathion degradation and toxicity reduction in solar photocatalysis and photolysis.

The solar photocatalytic degradation of methyl parathion was investigated using a circulating TiO2/solar light reactor. Under solar photocatalysis condition, parathion was more effectively degraded than solar photolysis and TiO2-only conditions. With solar photocatalysis, 20 mg/L of parathion was completely degraded within 60 min with a TOC decrease of 63% after 150 min. The main ionic byproducts during photocatalysis recovered from parathion degradation were mainly as NO3-, NO2- and NH4+, 80% of the sulphur as SO4(2-), and 5% of phosphorus as PO4(3-). The organic intermediates 4-nitrophenol and methyl paraoxon were also identified, and these were further degraded in solar photocatalytic condition. Two different bioassays (Vibrio fischeri and Daphnia magna) were used to test the acute toxicity of solutions treated by solar photocatalysis and photolysis. The Microtox test using V. fischeri showed that the toxicity expressed as EC50 (%) value increased from 5.5% to >82% in solar photocatalysis, indicating that the treated solution is non-toxic, but only increased from 4.9 to 20.5% after 150 min in solar photolysis. The acute toxicity test using D. magna showed that EC50 (%) increased from 0.05 to 1.08% under solar photocatalysis, but only increased to 0.12% after 150 min with solar photolysis, indicating the solution is still toxic. The pattern of toxicity reduction parallels the decrease in TOC and the parathion concentrations.     

Effect of storage temperature on phenolics stability in hawthorn (Crataegus pinnatifida var. major) fruits and a hawthorn drink

The stability of five major phenolics, namely (−)-epicatechin (EC), procyanidin B₂ (PC-B₂), chlorogenic acid (ChA), hyperoside (HP) and isoquercitrin (IQ), in hawthorn fruits and a canned hawthorn drink were evaluated during 6 months of storage in the dark at three different temperatures (4, 23 and 40 °C). HPLC with a diode-array detector was used to determine the contents of the individual compounds. The results showed that the studied phenolics in the hawthorn fruits and the drink were both stable at 4 °C and relatively unstable at 23 and 40 °C with varied extents of degradation. At room temperature (23 °C), marked degradations of EC and PC-B₂ were observed in both the fruits and the drink with around 50% and 30% decrease after a 6-month storage, respectively. A more significant decrease of the phenolics was observed at 40 °C, especially for EC and PC-B₂, which were almost completely degraded after a 6-month storage. HP, IQ and ChA were relatively stable at 23 °C, but unstable at 40 °C. Therefore, low-temperature storage is recommended for maintaining the quality and efficacy of hawthorn fruits and its preparations.     

Kinetics of AuSn4 migration in lead-free solders

The relatively fast diffusion of Au atoms in eutectic PbSn matrix is considered one of the contributing factors to the Au embrittlement problem. In this study, we further investigated the Au embrittlement problem in high-Sn solders. Experimentally, Sn3.5Ag (wt.%) spheres with 500-μm diameter were soldered over the Au/Ni soldering pads. It was found that some of the AuSn₄ needles that formed after reflow inside the solder migrated back to the solder/pad interface during thermal aging. However, the migration kinetics in high-Sn solders was slower compared to that in eutectic PbSn. The difference in migration kinetics of AuSn₄ in eutectic PbSn and SnAg was ascribed to the difference in the magnitudes of the Au flux and the Ni flux. In eutectic PbSn, the Au flux was much greater than that of the Ni flux, and the Au and Ni flux were in the same order of magnitude in eutectic SnAg. The relative magnitude of the Au and Ni flux changed in eutectic PbSn and SnAg because the homologous temperatures of PbSn and SnAg were different.     

Development of an end-point detector for parylene deposition process

Parylene is an emerging material for MEMS. It is an organic material that is grown by using the chemical vapor deposition method at room temperature. The deposition thickness is commonly controlled by the amount of solid-phase dimer loaded in a sublimation chamber. In a conventional deposition machine, the end point of the process is designated by the moment the dimer is exhausted. However, this end-of-process criterion does not offer precise, repeatable control of film thickness. We present the results of the development of an in situ end-point detector for a Parylene chemical vapor deposition process. The detector is based on the thermal transfer principle and can be implemented on commercial parylene deposition systems with minimal system modification. Such a sensor enables a user to stop the deposition when a targeted thickness is reached. The end point detector is very simple to implement on existing parylene deposition systems. A series of such sensors with different target deposition thickness would allow extraction of the actual deposition rate within a deposition run.     

Effects of tube rupture modeling and the parameters on the analysis of multiple steam generator tube rupture event progression in APR1400

A multiple steam generator tube rupture (MSGTR) event in APR1400 has been investigated using the best estimate thermal hydraulic system code, MARS1.4. The effects of the parameters such as the number of ruptured tubes, rupture location, affected steam generator on the analysis of the MSGTR event in APR1400 are examined. In particular, tube rupture modeling methods, single tube modeling (STM) and double tube modeling (DTM), are compared. The APR1400 is found to have the capability of allowing more than 30 min to operators for the MSGTR event of five tubes. The effects of rupture location on the MSSV lift time is not significant in the case of STM, but the MSSV lift time for tube-top rupture is found to be 25.3% larger than that for rupture at the hot-leg side tube sheet in the case of DTM. The MSSV lift time for the cases that both steam generators are affected (4C5x, 4C23x) are found to be larger than that of the single steam generator cases (4A5x, 4B5x) due to a bifurcation of the primary leak flow. The discharge coefficient of Cd is found to affect the MSSV lift time only for a smaller value of 0.5. It is found that the most dominant parameter governing the MSSV lift time is the leak flow rate. Whether any modeling method is used, it gives the similar MSSV lift time if the leak flow rate is close, except in the case where both steam generators are affected. Therefore, the system performance and the MSSV lift time of the APR1400 are strongly dependent on the break flow model used in the best estimate system code.     

Research on the Distant Hybrids of Wheat Obtained via Low-Energy Ion-Beam Implantation

Abstract The whole DNA of soybean was implanted into four varieties of wheat of Zhongyu5, Huaiyin 9628, Wenyou 1, Jimai 5 respectively via ion-beam mediation. There were 5 plantsobtained whose protein content was higher than 18.5%, the highest one was 21.44%. There were 3plants obtained whose protein content was lower than 11.5%, the lowest one was 10.96%. We cansee that the whole DNA of soybean transformed into wheat via ion beam implantation can inducethe increase in wheat protein content dramatically. The result also shows that the transformationefficiency of different gene types of wheat receptor varies greatly that the implanting time has acertain effect on the efficiency of transformation.     

A structured procedure for analysis and design of order pick systems

We present a structured procedure for order pick system (OPS) analysis and design that has been established on literature review and interviews with and presentations to OPS experts. In particular, we attempt to include the thinking processes that occur between OPS designers and owners. The design procedure and related issues are discussed in the order of input, selection, and evaluation stages.     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.