第三代短波自动链路建立系统特性分析及仿真实现

分析了第三代短波自动链路建立系统的工作特性及技术特点，并对系统仿真实现的原则及一些细节问题进行了较深入的探讨，同时对仿真实现中涉及的链路质量分析（LQA）算法进行了研究。     

Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

Thermodynamic modeling of native point defects and dopants of GaN semiconductors

A thermodynamic modeling of GaN was carried out to describe the thermodynamic behavior of native defects, dopants, and carriers (free electrons and holes) in GaN semiconductors. The compound energy model (CEM) was used. An unintentionally doped GaN was taken as an example. Oxygen was introduced into the model as the unintentionally doped impurity, according to the practical experimental phenomena. The energies of component compounds in the model were defined based on the results of the ab initio calculations and adjusted to fit experimental data. The thermodynamic properties of the defects and the oxygen doped were calculated to show the facility of the model.     

A network management architecture for robust packet routing in meshoptical access networks

We describe an architecture for an optical local area network (LAN) or metropolitan area network (MAN) access. The architecture allows for bandwidth sharing within a wavelength and is robust to both link and node failures. The architecture can be utilized with an arbitrary, link-redundant mesh network (node-redundancy is necessary only to handle all node failures), and assumes neither the use of a star topology nor the ability to embed such a topology within the physical mesh. Reservation of, bandwidth is performed in a centralized fashion at a (replicated) head end node, simplifying the implementation of complex sharing policies relative to implementation on a distributed set of routers. Unlike a router, however, the head end does not take any action on individual packets and, in particular, does not buffer packets. The architecture thus avoids the difficulties of processing packets in the optical domain while allowing for packetized shared access of wavelengths. We describe the route construction scheme and prove its ability to recover from single link and single node failures, outline a flexible medium access protocol and discuss the implications for implementing specific policies, and propose a simple implementation of the recovery protocol in terms of state machines for per-link devices     

大港白水头地区低阻油气层测井评价

在对白水头地区低阻油层的地质特征、物性特征及成因环境进行了分析研究后 ,应用测井曲线特征集法 ,把白水头油田常规油气层、低阻油气层、油水同层、水层等看成是独立的地质事件 ,建立了它们与测井曲线特征之间的对应关系 ,利用这种关系对未知地质事件进行了预测划分。最后根据所建模型定量计算储层各种参数 ,收到了良好的地质效果 ,表明测井曲线特征集法对于识别多成因的低阻油层是一种有效方法     

气液固三相相平衡热力学模型与计算方法

原油中含有大量的高分子有机固相物质，因此，要准确地描述油气体系相平衡，必须对气液固三相相平衡进行研究，在对高分子有机烃类沥青沉降机理有了一定的认识的基础上，提出了大的交互作用系数，可以描述沥青与原油中轻质不相容性的程度。根据对油气烃类混合物体系的一般性认识与提出的沥青组分特征化方法，导出了与之相应的有其自身特殊性的气液沥青三相相平衡物料平衡方程组，用考虑沥青沉降三相闪蒸数值算法，对沥青沉降进行有效的理化模拟计算，此外，结合实例分析，给出了沥青质参考逸度的计算，饱和压力和沉降量的拟合方法。     

机动武器系统的含间隙动力学研究--下篇:系统仿真

本文把中篇建立的间隙铰模型引入多体系统动力学分析中,得到了一种处理含间隙多体系统动力学问题的一般方法.应用这种方法对机动武器的发射过程进行了原理性的仿真,验证了前面建立的碰撞模型和间隙模型,并分析了间隙对导弹运动状态的影响.导弹发射过程具有变拓扑的特点,本文方法提供了一种处理这类问题的思路.     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

硼酸铝晶须增强环氧树脂和双马来酰亚胺树脂体系的研究

本文以硼酸铝晶须为增强剂，以4，5-环氧环己烷-1，2-二甲酸二缩水甘油酯(TDE-85)，甲基纳狄克酸酐(MNA)、N，N’-二胺基二苯甲烷型双马来酰亚胺(BMI)/O，O′-二烯丙基双酚A(BA)体系分别作为基体制备晶须增强复合材料。研究了晶须对树脂的尺寸、表面处理方法、含量对树脂体系力学性能和热性能的影响；通过扫描电子显微镜(SEM)分析了浇注体的弯曲、冲击断口，研究晶须的增强机理。