An extraction method to determine interconnect parasitic parameters

Interconnect parasitic parameters in integrated circuits have significant impact on circuit speed. An accurate monitoring of these parameters can help to improve interconnect performance during process development, provide information for circuit design, or give useful reference for circuit failure analysis. Existing extraction methods either are destructive (such as SEM measurement) or can determine only partial parasitic parameters (such as large capacitor measurement). In this paper, we present a new method for extracting interconnect parasitic parameters, which can simultaneously determine the interlayer and intralayer capacitances, line resistance, and effective line width. The method is based on two test patterns of the same structure with different dimensions. The structure consumes less wafer area than existing methods. The method shows good agreement with SEM measurement of dielectric thickness in both nonglobal planarized and chemical-mechanical polished processes, and gives accurate prediction of the process spread of a ring oscillator speed over a wafer     

光纤中受激喇曼散射的孤子效应

本文在综述近年来有关光孤子研究成果的基础上,对单模光纤中受激喇曼散射的喇曼孤子产生进行了详细地描述。从理论上分析了喇曼互作用及喇曼孤子的形成过程,讨论了喇曼孤子产生的实验方法及有关应用。     

CTS-26型超声探伤仪典型故障的分析与排除

在简要介绍CTS-26型超声探伤仪工作原理及组成的基础上。对其几种典型故障作了具体的分析和处理。     

气囊内模制作桥面板在华丰湾防洪工程中的应用

采用气囊作内模进行浇筑桥面板混凝土 ,加快了预制桥面板施工进度 ,确保工程施工质量 ,并降低了工程施工成本     

铝带材冷轧机机前展平辊重叠量的探讨

目前国内大多数铝加工厂对铝带材冷轧机机前展平辊的作用缺乏足够的认识，甚至弃而不用。本文主要论述展平辊的作用及展平辊重叠量的计算方法。     

军械调运方案优化算法的设计与仿真

军械调运问题的数学模型和手工算法过去已有研究,但是当问题较为复杂时,手工算法就要花费大量时间而且准确性也难以保证。针对这一缺陷,本文在已有的数学模型和手工算法的基础上,设计了一种可以用计算机实现的基于递归的算法来寻求军械紧急调运问题的最优方案,并使用面向对象的java语言将算法实现。     

环境湿度对贮存树脂的影响EI

通过对中温固化环氧树脂ＤＳＣ、扭辫分析、凝胶时间、粘度、力学性能的测定，固化反应活化能的计算，研究了在贮存树脂的过程中环境湿度对树脂的固化反应和性能的影响。     

SiCf/O′-SiAlON composite: properties and oxidation retained properties

A composite of O′SiAlON (Si_2-xAl_xN_2-xO_1+x, with x 0.14) reinforced with 20 vol.% SiC monofilaments was fabricated by hot-pressing, at 1600°C, for 2 h under 34 MPa pressure. The mechanical and interfacial properties of the composites, as-fabricated as well as post-oxidized, were, investigated. The composite exhibited a significant improvement in ultimate flexure strength (640 MPa) and work of fracture (42 kJ m⁻²) compared with that (350 MPa and 1.8 kJ m⁻², respectively) of the monolithic material. These mechanical properties were slightly increased after the composite was heat treated for 24 h in air at 1200 and 1300°C. However, the composite exhibited a significant degradation in ultimate strength, while the work of fracture (WOF) remained unchanged after exposure in air at temperatures beyond 1400°C. The as-fabricated composite revealed a low interfacial shear strength (6.2 MPa) and a frictional sliding stress (3.2 MPa). After the composite was oxidized at elevated temperatures, the interfacial bonding and sliding stresses were reduced to noticeable extents, resulting from the degradation of the carbon coating layer of the SiC monofilaments.     

激光辐照40Cr钢组织结构的穆斯堡尔谱分析

４０Ｃｒ钢试样经不同热处理后在空气中用ＣＯ２连续激光束进行辐照，以穆斯堡尔谱学研究试样在辐照后的组织结构变化。试验结果表明，调质预处理后再进行激光辐照的试样，不仅残作产奥氏体含量较低，而且其中碳的含量最低。