气囊内模制作桥面板在华丰湾防洪工程中的应用

采用气囊作内模进行浇筑桥面板混凝土 ,加快了预制桥面板施工进度 ,确保工程施工质量 ,并降低了工程施工成本     

铝带材冷轧机机前展平辊重叠量的探讨

目前国内大多数铝加工厂对铝带材冷轧机机前展平辊的作用缺乏足够的认识，甚至弃而不用。本文主要论述展平辊的作用及展平辊重叠量的计算方法。     

军械调运方案优化算法的设计与仿真

军械调运问题的数学模型和手工算法过去已有研究,但是当问题较为复杂时,手工算法就要花费大量时间而且准确性也难以保证。针对这一缺陷,本文在已有的数学模型和手工算法的基础上,设计了一种可以用计算机实现的基于递归的算法来寻求军械紧急调运问题的最优方案,并使用面向对象的java语言将算法实现。     

环境湿度对贮存树脂的影响EI

通过对中温固化环氧树脂ＤＳＣ、扭辫分析、凝胶时间、粘度、力学性能的测定，固化反应活化能的计算，研究了在贮存树脂的过程中环境湿度对树脂的固化反应和性能的影响。     

SiCf/O′-SiAlON composite: properties and oxidation retained properties

A composite of O′SiAlON (Si_2-xAl_xN_2-xO_1+x, with x 0.14) reinforced with 20 vol.% SiC monofilaments was fabricated by hot-pressing, at 1600°C, for 2 h under 34 MPa pressure. The mechanical and interfacial properties of the composites, as-fabricated as well as post-oxidized, were, investigated. The composite exhibited a significant improvement in ultimate flexure strength (640 MPa) and work of fracture (42 kJ m⁻²) compared with that (350 MPa and 1.8 kJ m⁻², respectively) of the monolithic material. These mechanical properties were slightly increased after the composite was heat treated for 24 h in air at 1200 and 1300°C. However, the composite exhibited a significant degradation in ultimate strength, while the work of fracture (WOF) remained unchanged after exposure in air at temperatures beyond 1400°C. The as-fabricated composite revealed a low interfacial shear strength (6.2 MPa) and a frictional sliding stress (3.2 MPa). After the composite was oxidized at elevated temperatures, the interfacial bonding and sliding stresses were reduced to noticeable extents, resulting from the degradation of the carbon coating layer of the SiC monofilaments.     

激光辐照40Cr钢组织结构的穆斯堡尔谱分析

４０Ｃｒ钢试样经不同热处理后在空气中用ＣＯ２连续激光束进行辐照，以穆斯堡尔谱学研究试样在辐照后的组织结构变化。试验结果表明，调质预处理后再进行激光辐照的试样，不仅残作产奥氏体含量较低，而且其中碳的含量最低。     

资产管理模型及其应用

简要介绍了水电厂资产管理系统的构成，从中引出了以设备为中心、以工作单为主线的资产管理模型，并说明了该模型在水电厂资产管理系统中的应用效果。