平面桁架构建的定日镜面形支撑结构优化及实验

针对反射面成型的复杂影响因素，提出平面桁架构建的定日镜面形支撑结构优化技术路线. 利用模拟仿真、数值计算和优化算法等方法，解析20 m²定日镜面形定义技术路线的4个组成环节：面形规格及宽高比、上弦杆的截面矩、平面桁架组间距的最优值、机加工中工艺控制要点的量化. 试制小型定日镜进行实验，分析光斑形状和能流密度分布特性，并与理想球面形光斑比较，两者的拟合优度大于0.98. 实验结果表明，当反射镜宽高比取1.2，上弦杆截面矩取40 000 mm⁴，桁架组间距取950 mm，上弦杆和斜杆的开孔公差小于0.9 mm时，反射面形的质量提升. 研究从原理和实践上证明了该优化技术路线的可行性.     

Structural,morphological, dielectric and magnetic properties of Zn-Zr co-doping yttrium iron garnet

In this study, yttrium iron garnet co-doped with Zn and Zr atoms with a chemical formula Y₃Zn_xZr_xFe_(5−2x)O₁₂ (x = 0.0-0.3) has been successfully prepared by the solid-state reaction method. The effects of doping concentration on the microstructure, crystal structure, magnetic properties, and dielectric properties of Y₃Zn_xZr_xFe_(5−2x)O₁₂ were investigated. The microstructure analysis indicates that co-doping of YIG with Zn and Zr can effectively reduce the grain size of the ceramic. The crystal structure results reveal that the doping concentration of Zn–Zr has substantial influence on the lattice parameters of YIG, such as, increases the lattice constant, crystal cell size, and interplanar spacing. However, the second phase of ZrO₂ appears once x ≥ 0.15. Additionally, the dielectric properties of YIG ferrite can be regulated using this Zn–Zr co-doping method. Zn–Zr co-doping can improve the dielectric stability and reduce the dielectric loss at high temperature. The magnetization measurement shows that the saturation magnetization is stabilized at x < 0.15, and the magnetic loss is decreased with the increase in the doping concentration. Overall, the findings show that the ceramic with x = 0.1 exhibits better properties included high saturation magnetization (24.607 emu/g), low magnetic loss (0.0025 @ 1 MHz), and relatively low dielectric loss (496 @ 400°C).     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

Sparse non-convex Lp regularization for cone-beam X-ray luminescence computed tomography

Cone-beam X-ray luminescence computed tomography (CB-XLCT) is an attractive hybrid imaging modality, and it has the potential of monitoring the metabolic processes of nanophosphors-based drugs in vivo. However, the XLCT imaging suffers from a severe ill-posed problem. In this work, a sparse nonconvex L_p (0?p?L₁ regularization. Further, an iteratively reweighted split augmented lagrangian shrinkage algorithm (IRW_SALSA-L_p) was proposed to efficiently solve the non-convex L_p (0?p?p-values (1/16, 1/8, 1/4, 3/8, 1/2, 5/8, 3/4, 7/8) in both 3D digital mouse experiments and in vivo experiments. The results demonstrate that the proposed non-convex methods outperform L₂ and L₁ regularization in accurately recovering sparse targets in CB-XLCT. And among all the non-convex p-values, our L_p(1/4?p?相似文献   

Computational Analysis of the Solid-State and Solvation Properties of Carbamazepine in Relation to its Polymorphism

The solvent-dependent polymorphism of the active pharmaceutical ingredient (API) carbamazepine is interpreted from calculations of the solid-state and API-solvent intermolecular interactions. These simulations suggested that apolar solute-solute interactions could be disrupted by apolar solvents. In contrast, the polar solute-solute interactions were found to be easily disrupted by polar and protic solvents. This is consistent with experimental observations that the crystallization of the metastable form II is more dominant in apolar solvents. The Mercury program remains the gold standard in terms of usability; however, further expansion into more complex simulation techniques could make this package of even greater use in pharmaceutical manufacturing workflows.     

Transformation of the reabsorption characteristics of lignite treated by low and high temperature drying process

Abstract

The reabsorption characteristics of the lignite treated by low and high temperature drying process were addressed in the paper. The information about the moisture form, functional groups, effective water-filled porosities and equilibrium moisture content of the lignite before and after the drying process was investigated using Differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy and a self-made reabsorption device, respectively. The results show that the low drying temperature (140, 190, 230?°C, 10?min, N₂) has little impact on the effective water-filled porosities of the resulted samples, whereas it has a great influence on the main oxygen-containing functional groups, which amount firstly decreases and then increases with the drying temperature increasing. In the case of the lignite samples dried under high-temperature (600, 700, 800?°C, 30?s, N₂), the amount of the effective water-filled porosity of the sample decreases and the amount of oxygen-containing functional groups increases as the temperature increasing. The reabsorption capability of the high temperature dried sample is much lower than that of the sample treated under low drying temperature. The reabsorption characteristics of the low-temperature dried samples are affected by the amount of the oxygen-containing functional groups, while the effective water-filled porosity is main factor for the lignite samples derived from high temperature drying process. Moreover, the work gives a good evidence that the high-temperature drying process is an effective choose for lignite upgrading.     

Dynamics and workspace analysis of a multi-robot collaborative towing system with floating base

Journal of Mechanical Science and Technology - A multi-robot collaborative towing system fixed on floating base for high load marine work was established in this paper, and its dynamics and...