Study of the amination of fatty alcohols catalyzed by Cu−Ni catalysts

Amination of fatty alcohols by hydrogenation and dehydrogenation catalysis is one of the main commercial processes for the production of dimethylalkylamines. The key factor in this process is the preparation of catalysts with high selectivity. A study of amination catalyzed by Cu−Ni catalysts supported on CaCO₃ is reported in this paper. Selectivity of the catalysts was adjustable by varying the ratio of Cu to Ni or by adding a third element (Zn or Mg). The promotion of catalyst selectivity was mainly attributable to the effect of the components on the reducibility of Ni²⁺ in the catalysts. Lower reducibility of Ni²⁻ led to higher catalyst selectivity.     

HT-730改性酚醛-丁腈胶粘剂的研制

对酚醛-丁腈胶粘剂进行改性，添加5．0％的硅烷偶联剂，改善了酚醛-丁腈胶粘剂的工艺性能，提高了粘接强度，特别是降低了酚醛-丁腈胶对环境湿度的敏感性。研制的HT-730胶在环境湿度90％时仍有很高的粘接强度，同时老化性能和适用期并没有受到影响。     

Study of different effect on foaming process of biodegradable bionolle in supercritical carbon dioxide

Microcellular foaming of biodegradable Bionolle in supercritical CO₂ has been produced. The effects of a series of variable factors, such as saturation temperature, saturation pressure, and depressurization time and step on the foam structures and density, were studied through measurement of density and SEM observation. The experimental results show that higher saturation temperatures lead to an increase in bulk densities; and different depressurization time and step result in different product cell morphology. In addition, at some saturation temperature, the orientation of the cells can be found in the product morphology. XRD experimental results show that the foaming treatment with SC CO₂ increased the crystallinity of Bionolle. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2901–2906, 2006     

Study on early warning index of spatial deformation for high concrete dam

Owing to the deficiency in early warning for high concrete dam,a formula was established to characterize the deformation behavior of high concrete dam as a whole.The early warning index of spatial deformation was calculated by low probability principle on the basis of the deformation entropy formula proposed.The steps were as follows.Firstly,the probability method was utilized to define the degree of order and degree of chaos for each survey point.Secondly,the weight distribution among the survey points was...     

Full-scaled deep metric learning for pedestrian re-identification

Multimedia Tools and Applications - The pedestrian re-identification problem (i.e., re-id) is essential and pre-requisite in multi-camera video surveillance studies, provided the fact that...     

NN-based Prediction Interval for Nonlinear Processes Controller

Neural networks (NNs) are extensively used in modelling, optimization, and control of nonlinear plants. NN-based inverse type point prediction models are commonly used for nonlinear process control. However, prediction errors (root mean square error (RMSE), mean absolute percentage error (MAPE) etc.) significantly increase in the presence of disturbances and uncertainties. In contrast to point forecast, prediction interval (PI)-based forecast bears extra information such as the prediction accuracy. The PI provides tighter upper and lower bounds with considering uncertainties due to the model mismatch and time dependent or time independent noises for a given confidence level. The use of PIs in the NN controller (NNC) as additional inputs can improve the controller performance. In the present work, the PIs are utilized in control applications, in particular PIs are integrated in the NN internal model-based control framework. A PI-based model that developed using lower upper bound estimation method (LUBE) is used as an online estimator of PIs for the proposed PI-based controller (PIC). PIs along with other inputs for a traditional NN are used to train the PIC to predict the control signal. The proposed controller is tested for two case studies. These include, a chemical reactor, which is a continuous stirred tank reactor (case 1) and a numerical nonlinear plant model (case 2). Simulation results reveal that the tracking performance of the proposed controller is superior to the traditional NNC in terms of setpoint tracking and disturbance rejections. More precisely, 36% and 15% improvements can be achieved using the proposed PIC over the NNC in terms of IAE for case 1 and case 2, respectively for setpoint tracking with step changes.

     

Reaction mechanism and microstructure evolution of reaction sintered <Emphasis Type="Italic">h</Emphasis>-BN

Hexagonal boron nitride ceramic (h-BN) based on the nitridation of B powders was obtained by reaction sintering method. The effects of sintering temperature on the mechanical properties and microstructure of the resultant products were investigated and the reaction mechanism was discussed. Results showed that the reaction between B and N₂ occurred vigorously at temperatures ranging from 1 000 °C to 1 300 °C, which resulted in the generation of t-BN. When the temperature exceeded 1 450 °C, transformation from t-BN to h-BN began to occur. As the sintering temperature increased, the spherical particles of t-BN gradually transformed into fine sheet particles of h-BN. These particles subsequently displayed a compact arrangement to achieve a more uniform microstructure, thereby increasing the strength.     

Estimation of access failure probability in D2D underlaid cellular networks

Device-to-Device (D2D) communication can reduce the mobile devices' energy consumption and increase the spectral efficiency in D2D underlaid cellular networks. However, D2D users will interfere with co-channel cellular users, which can lead to cellular communication access failures. There are two reasons for cellular communication access failures: (1)D2D interference and (2)insufficient spectrum resources. To address the absence of research on the performance of cellular services' access in D2D underlaid cellular networks, this paper defines the new services' access failure probability and handoff services' access failure probability to evaluate the effect of both D2D interference and limited resources on cellular communication access. Based on the stochastic geometry and stochastic process, a random network model is presented to estimate the access failure probabilities, which can provide guidelines for network design to ensure cellular services' access. The accuracy of the estimated access failure probability is validated through extensive simulations.     

综合物探方法在地面塌陷勘察中的应用

地面塌陷引发的地质灾害对国民经济建设的危害重大。目前,探测塌陷区的物探方法种类繁多,但没有一种方法能全面解决各种问题,需综合运用多种方法。以安徽某地面塌陷研究对象,运用高密度电法和瞬变电磁法探测重点塌陷区域,简要介绍了高密度电法、瞬变电磁法的工作原理、方法特点、数据采集和数据处理,并对数据进行了解释,通过此次探测研究,取得了明显的成果。结果表明,两种方法相互验证,相互参照,相互补充,查明了塌陷区及其附近的覆盖层厚度、地质构造和地层岩性变化,为后期地面塌陷灾害治理提供了科学依据。     

Degradability and biocompatibility of bioglass/poly(amino acid) composites with different surface bioactivity as bone repair materials

Bioglass (BG) possesses excellent bioactivity and has been widely used in the manufacture of biomaterials. In this study, a composite with different surface bioactivity was fabricated via in situ melting polymerization by incorporating BG and poly(amino acid) (PAA) at a suitable ratio. The structure of the composite was characterized by Fourier transform infrared spectroscopy and XRD. The compressive strength of the BG/PAA composites was 139 MPa (BG:PAA = 30:70). The BG/PAA composites were degradable, and higher BG in composite showed higher weight loss after 4 weeks of incubation in simulated body fluid. In addition, the BG/PAA composite maintained adequate residual compressive strength during the degradation period. The SEM results showed the differences in surface bioactivities of the composites directly, and 30BG/PAA composite showed thicker apatite layer and higher Ca/p than 15BG/PAA. in vitro MG-63 cell culture experiments showed that the composite was noncytotoxic and thus allows cells to adhere, proliferate, and differentiate. This indicates that the composite has good biocompatibility. The implantations in the bone defects of rabbits for 4 and 12 weeks were studied. The composites had good biocompatibility and were capable of guiding new bone formation without causing any inflammation. The composite may be successfully used in the development of bone implants.