浅谈碾压混凝土的施工技术

介绍碾压混凝土坝发展的历程，简述了碾压混凝土筑坝技术以及施工工艺、特点、程序、质量控制等相关方面的施工经验。     

Effect of grain boundary phase on the thermal conductivity of aluminium nitride ceramics

AIN with high thermal conductivity was fabricated by pressureless sintering with Y₂O₃ as the sintering aid. The thermal conductivity was observed to increase with sintering time (up to 8 h) at 1810 °C. The distribution of the sintering aid was identified as one of the major factors influencing the thermal conductivity in AIN. Non-uniform distribution of the grain boundary phase was found to be associated with a significant amount of porosity, resulting in the enhancement of phonon scattering and thereby lowering the thermal conductivity.     

海上采油作业安全灭火措施--推广采用高倍泡沫灭火技术

对海洋石油平台火灾进行分析 ,提出采用高倍泡沫灭火技术与密集水流相结合的优化灭火措施建议 ,并介绍锦州 93平台应用实例     

CALCULATION ON TWO-PHASE FLOW TRANSIENTS AND THEIR EXPERIMENTAL RESEARCH

From basic equations of gas-liquid, solid-liquid, solid-gas two-phase flow, the calculating method on flow transients of two-phase flow is developed by means of characteristic method. As one example, a gas-liquid flow transient is calculated and it agrees well with the experimental result. It is shown that the method is satisfactory for engineering demand.     

硝酸铵的膨化机理研究

膨化硝酸铵是一种自敏化改性硝酸铵,由硝酸铵溶液在专用表面活性剂作用下,经真空强制析晶工艺制得.文中研究了膨化硝酸铵制备的膨化过程和专用表面活性剂的作用,结果表明:在真空和表面活性剂作用下,硝酸铵溶液由不饱和状态至饱和状态,进而达到过饱和状态,最终导致硝酸铵的快速结晶和体系的膨胀.在真空干燥过程中,形成中心空穴、微细孔道和裂缝,它们使膨化硝酸铵的起爆感度提高;专用表面活性剂具有降低硝酸铵溶液表面张力、发泡剂和加快结晶成核的作用.     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

Numerical simulation of aerosol collection in filters with staggered parallel rectangular fibres

 In this paper, filters with rectangular fibres arranged in a staggered and parallel array and placed transverse to the flow are studied numerically. A two- dimensional flow field is obtained by solving Navier–Stokes equations with the control volume method. Periodic boundary conditions are introduced in the calculation. In order to achieve higher accuracy, a second-order upwind scheme is adopted and a fine mesh is arranged near the fibre and the symmetrical plane of the flow field where large gradients in velocity are expected. Particle trajectories are calculated by solving the corresponding Lagrangian equation of motion to obtain the collection efficiency of a single rectangular fibre, in which positions of the approaching particles on the inlet plane of the flow field are randomly distributed according to the Monte-Carlo principle. The simulation considers all the important mechanisms of particle capture including interception, inertial impaction and Brownian motion. Effects of fibre aspect ratio, filter packing density, particulate size and Reynolds number on the collection efficiency are numerically determined. The volumetric packing density ranges from 0.4 to 4% and the particle diameter is from 0.01 μm to 2 μm. Reynolds number based on the height of computational domain varies from 20 to 100 and the aspect ratio is from 0.1 to 10. Simulations with and without Brownian motion are carried out for different Reynolds numbers, packing densities and aspect ratios and the results show that Brownian effects are significant for particles smaller than 1 μm. Received 25 May 2001     

玻璃钢包扎在煤气管道加强上的应用

介绍了玻璃钢包扎煤气管道的施工材料、施工流程及要点，指出了此方法应用在煤气管道加强上的优点。     

The relationship between preparation convergence and retention of extracoronal retainers

PURPOSE: Although traditional ideal convergence (the sum of taper of the opposite sides) for crown preparation has been arbitrarily set at 4 degrees to 10 degrees, some believe absolute parallelism yields the highest retention. This study examined the relationship between the degree of convergence of a machined metal die and the retention of its casting. MATERIALS AND METHODS: The method used was that of cementing cast metal crowns onto full crown preparations on brass dies with varying convergence angles, and then recording the force required to remove the crowns from the dies in a vertical direction using a Tate-Emery Testing Machine and Load Indicator. RESULTS: It was found that retention (i.e., the force needed to remove the cemented castings from the die in their common long axis) increases from 0 degree convergence to peak between 6 degrees to 12 degrees convergence. It also seems that a critical film thickness does exist for optimum retention, and that film thicknesses smaller than the critical thickness may be responsible for the phenomenon that we have observed and directly related to the convergence angle itself. CONCLUSIONS: There seems to be experimental data supporting the use of traditionally taught convergence. Our study found that convergence angles between 6 degrees and 12 degrees seem to be optimum for tooth crown preparation when one plans to use zinc phosphate cement. Convergence angles of less than 6 degrees may not be desirable even if they can be clinically achieved. The results of our study indicate that a relationship exists between the convergence angle and the critical cement thickness that is necessary to realize the maximum strength properties of zinc phosphate cement.