Effect of silanes on the morphology,hydrophobicity, and dynamical mechanical properties of polyimide/silica hybrid membranes

Polyimide (PI)/silica hybrid membranes with high contact angles were prepared through the in situ sol–gel process. The precursor, poly(amic acid) with controlled block chain length, was synthesized using 4,4′‐diaminodiphenyl ether (ODA), 3,3′,4,4′‐benzophenone‐tetracarboxylic dianhydride (BTDA) and 3‐aminopropyl‐trimethoxysilane (APrTMOS) or 3‐aminopropyldimethylethoxysilane (APDiMOS). And then, phenyltrimethoxysilane (PTS) or tetramethoxysilane (TMOS) or methyltrimethoxysilane (MTrMOS) was respectively, added to the above polyamic acid and mixed thoroughly. Following curing reaction, the PI/silica hybrid membranes with different cross‐linkages, silica content, and hydrophobic properties were prepared. The effect on the formation of PI imide ring during imidization reaction is increased as the increase of silanes content and characterized by frequency shiftment and absorbance ratio of Fourier transform infrared (FTIR) measurements. All the hybrid membranes show high transparency though with high silica contents. The storage modulus, tan δ, and damping intensity by DMA measurements are all correlated with silane content or block chain length. And all these membranes with silane content possess high contact angle as compared to pure PI without any silanes added and the contact angles increase with increasing the silane content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Rheology of concentrated solutions of hyperbranched polyesters

The solution rheology of different generations of hyperbranched polyesters in N‐methyl‐2‐pyrrolidinone (NMP) solvent was examined in this study. The solutions exhibited Newtonian behavior over a wide range of polyester concentrations. Also, the relative viscosities of poly(amidoamine) (PAMAM) dendrimers in ethylenediamine were compared with those of the hyperbranched polyesters in NMP. Both types of dendritic polymers have relative viscosities that are exponential functions of their molar fraction in solution. The slopes of these relative viscosity curves show a linear relationship with respect to the generation number. PAMAM dendrimers have the greater slopes for each generation, reflecting their relatively larger intrinsic viscosity values.     

Low-Temperature Sintering and Microwave Dielectric Properties of Anorthite-Based Glass-Ceramics

TiO₂ nucleated anorthite-based glass-ceramics were fabricated from glass powders. After sintering and crystallization heat treatment, various physical properties, including apparent bulk density and water absorption, were examined to evaluate the sintering behavior of anorthite-based glass-ceramic. Results showed that the complete-densification temperature for specimens was as low as 900°C. Sufficient crystallization was achieved by subsequently raising the firing temperature to 950°C, and the dielectric quality factor was promoted to the maximum value. Contents of nucleating agent (TiO₂) played an important role in the dielectric constants. The crystallinity was controlled by raising the firing temperature at a constant heating rate. The degree of crystallization affected the dielectric properties of sintered glass-ceramics. At the resonant frequency of 10 GHz, anorthite glass-ceramics with 5 wt% TiO₂ possessed the lowest permittivity of 8 and exhibited appropriate dielectric properties as compared with those with B₂O₃ and 10 wt% TiO₂.     

Effect of montmorillonite clay addition on the morphological and physical properties of Jatropha curcas L. and Glycine max L. protein concentrate films

Protein concentrates from jatropha (JPC) and soy seeds (SPC) were obtained by solubilization and acid precipitation of proteins. JPC and SPC films were prepared by the casting method, using two different montmorillonite (MMT) clay concentrations and plasticized with glycerol. Film properties were evaluated by scanning electron microscopy, transmission electron microscopy, X‐ray diffraction (XRD), Fourier transform infrared spectroscopy, thermogravimetric analysis, tensile properties, water retention, and water vapor transmission rate (WVRT). Typical tactoid microcomposite structures were found to be heterogeneously dispersed in the films containing MMT. A small XRD peak was found in films with MMT. Slight improvements in thermal stability and tensile strength were observed in the films with MMT. Reductions in water retention and WVRT were obtained when MMT was added into the films. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44459.     

Biodegradable composites based on starch/EVOH/glycerol blends and coconut fibers

Unripe coconut fibers were used as fillers in a biodegradable polymer matrix of starch/ethylene vinyl alcohol (EVOH)/glycerol. The effects of fiber content on the mechanical, thermal, and structural properties were evaluated. The addition of coconut fiber into starch/EVOH/glycerol blends reduced the ductile behavior of the matrix by making the composites more brittle. At low fiber content, blends were more flexible, with higher tensile strength than at higher fiber levels. The temperature at the maximum degradation rate slightly shifted to lower values as fiber content increased. Comparing blends with and without fibers, there was no drastic change in melt temperature of the matrix with increase of fiber content, indicating that fibers did not lead to significant changes in crystalline structure. The micrographs of the tensile fractured specimens showed a large number of holes resulting from fiber pull‐out from the matrix, indicating poor adhesion between fiber and matrix. Although starch alone degraded readily, starch/EVOH/glycerol blends exhibited much slower degradation in compost. Composites produced 24.4–28.8% less CO₂ compared with starch in a closed‐circuit respirometer. Addition of increasing amount of fiber in starch/EVOH/glycerol composite had no impact on its biodegradation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of operating parameters on photocatalytic degradation of phenol in UV/TiO2 process

The use of hydrogen peroxide (H₂O₂) for improved photocatalytic degradation of phenol in aqueous suspension of commercial TiO₂ powders (Degussa P-25) was investigated. Photodegradation was compared using direct photolysis (UV alone), H₂O₂/UV, TiO₂/UV, and H₂O₂/TiO₂/UV processes in a batch reactor with high-pressure mercury lamp irradiation. The effects of operating parameters such as catalyst dosage, light intensity, pH of the solution, the initial phenol, and H₂O₂ concentrations on photodegradation process were examined. It was shown that photodegradation using H₂O₂/TiO₂/UV process was much more effective than using either H₂O₂/UV or TiO₂/UV process. The effect of the initial phenol concentration on TOC removal was also studied, demonstrating that more than 8 h was required to completely mineralize phenol into water and carbon dioxide. For all the four oxidation processes studied, photodegradation followed the first-order kinetics. The apparent rate constants with 400-W UV ranged from 5.0 × 10⁻⁴ min⁻¹ by direct photolysis to 1.4 × 10⁻² min⁻¹ using H₂O₂/TiO₂/UV process. The role of H₂O₂ on such enhanced photodegradation of phenol in aqueous solution was finally discussed.     

Thermally and mechanically enhanced epoxy resin‐silica hybrid materials containing primary amine‐modified silica nanoparticles

In this article, a series of hybrid materials consisted of epoxy resin matrix and well‐dispersed amino‐modified silica (denoted by AMS) nanoparticles were successfully prepared. First of all, the AMS nanoparticles were synthesized by performing the conventional acid‐catalyzed sol–gel reactions of tetraethyl orthosilicate (TEOS), which acts as acceded sol–gel precursor in the presence of 3‐aminopropyl trimethoxysilane (APTES), a silane coupling agent molecules. The as‐prepared AMS nanoparticles were then characterized by FTIR, ¹³C‐NMR, and ²⁹Si‐NMR spectroscopy. Subsequently, a series of hybrid materials were prepared by performing in situ thermal ring‐opening polymerization reactions of epoxy resin in the presence of as‐prepared AMS nanoparticles and raw silica (RS) particles (i.e., pristine silica). AMS nanoparticles were found to show better dispersion capability in the polymer matrices than that of RS particles based on the morphological observation of transmission electron microscopy (TEM) study. The better dispersion capability of AMS nanoparticles in hybrid materials was found to lead enhanced thermal, mechanical properties, reduced moisture absorption, and gas permeability based on the measurements of thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and gas permeability analysis (GPA), respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Alloy ratio effect of Pd/Pt nanoparticles on carbon nanotubes for catalysing methanol-tolerant oxygen reduction

Pd₁Pt₃, Pd₁Pt₁, and Pd₃Pt₁ nanoparticles supported on multi-wall carbon nanotubes (CNTs) were prepared by the self-regulation reduction of sodium n-dodecyl sulphate and used as catalysts in oxygen reduction reactions (ORRs). The crystal properties of these alloy nanoparticles on the CNT were measured by X-ray diffraction spectroscopy (XRD) and high-resolution transmission electron microscopy (HRTEM). The angle shifting of the XRD peak and the lattice spacing of the nanoparticles measured by HRTEM increased with an increase in Pd amount, indicating a regulable Pd-Pt ratio for the alloy nanoparticle composition. Rotating ring-disk electrode (RRDE) measurements indicate that the number of electrons catalysed by the Pd₁Pt₃/CNT, Pd₁Pt₁/CNT, and Pd₃Pt₁/CNT nanocatalysts in the ORRs were 3.98, 3.97, and 3.93, respectively. These results show that these ORRs occur via a 4-electron pathway. Linearly scanned voltammetry in the electrolyte with methanol revealed that Pd₃Pt₁/CNT has high methanol tolerance during ORRs.     

Induced Pluripotent Stem Cell-Derived Conditioned Medium Promotes Endogenous Leukemia Inhibitory Factor to Attenuate Endotoxin-Induced Acute Lung Injury

The conditioned medium of induced pluripotent stem cells (iPSC-CM) can attenuate neutrophil recruitment and endothelial leakage of lipopolysaccharide (LPS)-induced acute lung injury (ALI). Therefore, we investigated the mechanisms by which iPSC-CM regulate the interaction between neutrophils and the endothelium in ALI. Murine iPSCs (miPSCs) were delivered intravenously to male C57BL/6 mice (8–12 weeks old) 4 h after intratracheal LPS injection. A miPSC-derived conditioned medium (miPSC-CM) was delivered intravenously to mice after intratracheal LPS injection. DMSO-induced HL-60 cells (D-HL-60, neutrophil-like cells) and human umbilical vein endothelial cells (HUVECs) were used as in vitro models to assess the interaction of neutrophils and endothelial cells. miPSC-CM diminished the histopathological changes in the lungs and the neutrophil count in bronchoalveolar lavage fluids of ALI mice. miPSC-CM attenuated the expression of adhesion molecules in the lungs of ALI mice. Human iPSC conditioned medium (hiPSC-CM) reduced the expression of adhesion molecules in a HUVEC and D-HL-60 co-culture after LPS stimulation, which decreased the transendothelial migration (TEM) of D-HL-60. A human angiogenesis factors protein array revealed that leukemia inhibitory factor (LIF) was not detected in the absence of D-HL-60 and hiPSC-CM groups. hiPSC-CM significantly promoted the production of endogenous LIF in in vitro models. Administration of an anti-LIF antibody not only reversed the effect of iPSC-CM in ALI mice, but also blocked the effect of iPSC-CM on neutrophils TEM in in vitro models. However, a controlled IgG had no such effect. Our study demonstrated that iPSC-CM promoted endogenous LIF to inhibit neutrophils TEM and attenuate the severity of sepsis-induced ALI.     

Oil sensitivity and its asymmetric impact on the stock market

We develop a two-step methodology to facilitate an examination of the impact of oil shocks on stock returns. Oil price volatility is monitored in this study through the use of a regime-switching model, with the presence of jumps subsequently being taken into consideration to examine the asymmetric effects of oil prices on stock returns. Our analysis provides quite conclusive results based upon the use of a regime-switching model with consideration of jumps; that is, when there are significant fluctuations in oil prices (West Texas Intermediate; WTI), the resultant unexpected asymmetric price changes lead to negative impacts on S&P 500 returns. However, the same result does not hold in a regime of lower oil price fluctuations. We therefore suggest that the achievement of a well diversified portfolio should involve the consideration of oil price shocks, which, as a consequence, should also help to improve the accuracy of hedging against oil price risks.