Effect of backwashing on perchlorate removal in fixed bed biofilm reactors

The influence of backwashing on biological perchlorate reduction was evaluated in two laboratory scale fixed bed biofilm reactors using 1- or 3-mm glass beads as support media. Influent perchlorate concentrations were 50 microg/L and acetate was added as the electron donor at a concentration of 2 mg C/L. Perchlorate removal was evaluated at various influent dissolved oxygen (DO) concentrations. Complete perchlorate removal was achieved with an influent DO concentration of 1mg/L resulting in bulk phase DO concentrations below the detection limit of 0.01 mg/L. The influence of increasing influent DO concentrations for 12 h periods was evaluated before and after individual backwash events. Partial perchlorate removal was achieved with an influent DO concentration of 3.5 mg/L before a strong backwash (bulk phase DO concentrations of approximately 0.2mg/L), while no perchlorate removal was observed after the strong backwash at the same influent DO level (bulk phase DO concentrations of approximately 0.8 mg/L). The immediate effect of backwashing depended on influent DO concentrations. With influent DO concentrations of 1 mg/L, strong backwashing resulted in a brief (<12 h) increase of effluent perchlorate concentrations up to 20 microg/L; more pronounced effects were observed with influent DO concentrations of 3mg/L. Daily weak backwashing had a small and, over time, decreasing negative influence on perchlorate reduction, while daily strong backwashing ultimately resulted in the breakdown of perchlorate removal with influent DO concentrations of 3 mg/L.     

Effects of Sesame Oil Addition to Soybean Oil During Frying on the Lipid Oxidative Stability and Antioxidants Contents of the Fried Products During Storage in the Dark

ABSTRACT: Effects of sesame oil addition to soybean oil during frying on the lipid oxidative stability and antioxidants contents of fried products during storage in the dark were studied. Flour dough pieces (2 cm × 2 cm × 0.1 cm) were fried at 160 °C for 1 min in sesame oil-added soybean oil. Concentrations of sesame oil in the frying oil were 0%, 10%, and 20% by volume. Fried products were put into a glass bottle, and the bottles were tightly sealed and stored at 60 °C in the dark for 18 d. Lipid oxidation of fried products was determined by fatty acid composition changes and conjugated dienoic acid (CDA) and p -anisidine (PA) values. Tocopherols and lignan compounds in the fried products were determined by high-performance liquid chromatography. Relative content of linolenic acid decreased, and CDA and PA values increased during storage of the fried products in the dark. Fatty acid composition change and CDA and PA values during storage were lower in the products fried in sesame oil-added soybean oil than in the products fried in soybean oil without sesame oil. The results clearly showed that addition of roasted sesame oil to soybean oil at 10% and 20% during frying decreased the lipid oxidation of fried products during storage in the dark for 18 d by extension of induction period and decrease in decomposition of oxidized lipids. Fried products contained 134 to 267 ppm tocopherols and 0 to 148 ppm lignans before storage; however, their contents decreased during storage in the dark. Lignan compounds were more stable than tocopherols, and the rate of tocopherols degradation was lower in the products fried in sesame oil-added soybean oil than in the products fried in soybean oil without sesame oil, which could be because of protection of tocopherols from degradation by lignan compounds.     

Correlations between histopathologic and dermoscopic findings in Korean actinic keratosis

Skin biopsy for AK diagnosis is usually performed on only a limited part of the whole lesion. Therefore, a clinical diagnosis is important. According to a study, there is no significant correlation between histopathological and clinical classification system. We examined the correlation between microscopic information and dermoscopic findings to deduce if dermoscopic information reflects histopathologic grade severity. Forty seven patients with histologically confirmed AK were enrolled and positive ratio of red pseudonetwork, rosette, red background and targetoid signs, white‐to‐yellow scale, white structureless area, and pigmentation from dermoscopic findings were investigated. Furthermore, viable epidermal thickness, vessel lumen dimensions, existence and thickness of ortho‐ and parakeratosis, degree of sola elastosis, flag sign existence, and Roewert‐Huber classification were measured as histologic findings. Red background did not show a significant correlation with vascular dimension or viable epidermal thickness. When targetoid sign was present, vascular dimension was significantly larger but showed no correlation with viable epidermal thickness, parakeratosis or orthokeratosis. Solar elastosis level was significantly higher when white‐to‐yellow scale was present. According to Spearman's correlation analysis, ortho/parakeratotic thickness showed correlations with each other. The negative correlation between viable epidermal thickness and vascular dimension was also shown. Roewert‐Huber histologic AK classification showed no correlation with any factors we checked. Factors considered to be characteristic features of AK in dermoscopy seemed unassociated with histologic AK classification and additional research is needed to determine degree of dysplasia of AK lesions using dermoscopy.     

Effect of nanoclay addition on the foaming behavior of linear polypropylene‐based soft thermoplastic polyolefin foam blown in continuous extrusion

The goal of this study is to fabricate a soft foam with high cell density and high foam expansion based on thermoplastic polyolefin (TPO), and to supply a potential candidate for soft thermoset foams. It was found that a linear polypropylene (PP)‐based TPO foam exhibited very poor cell morphology because of its weak melt strength. Nanoclay was introduced into the TPO to improve its foaming behavior. The extrusion foaming experiments demonstrated that the introduction of 0.5 wt% nanoclay significantly increased the cell morphology and expansion ratio of TPO/clay nanocomposite foams due to the enhanced cell nucleation and the possible cell coalescence suppression at low temperatures. At a high nanoclay content of 2.0 wt%, the cell density and foam expansion of foams increased continuously compared with the 0.5 wt% nanoclay addition. Our study suggested that it was possible to produce soft TPO foams with a well‐defined cell structure and high foam expansion using a continuous method, but that a proper PEOc content control was needed to maximize foam expansion. POLYM. ENG. SCI., 2011. ©2011 Society of Plastics Engineers.     

Photocurrent effect on the zero-Bias dynamic resistance of HgCdTe photodiode

A new physical model is presented for the illumination-dependence of the zero-bias resistance-area product (R₀A) of HgCdTe photodiode. The model is based on three independent mechanisms. They are the depletion region volume change with the applied bias, the diffusion distance change with the moving depletion region edge, and the minority carrier accumulation in the depletion region which affects the minority carrier diffusion. Analytic equations are derived for the photodiode current-voltage characteristics and R₀A products. The results of the model have been compared with experimental data obtained from several Hg_0.7Cd_0.3Te diodes with an identical diode structure having different absorbing amount of light. The model showed good agreement with the experimental data.     

High‐Performance Sodium‐Ion Hybrid Supercapacitor Based on Nb2O5@Carbon Core–Shell Nanoparticles and Reduced Graphene Oxide Nanocomposites

Sodium‐ion hybrid supercapacitors (Na‐HSCs) have potential for mid‐ to large‐scale energy storage applications because of their high energy/power densities, long cycle life, and the low cost of sodium. However, one of the obstacles to developing Na‐HSCs is the imbalance of kinetics from different charge storage mechanisms between the sluggish faradaic anode and the rapid non‐faradaic capacitive cathode. Thus, to develop high‐power Na‐HSC anode materials, this paper presents the facile synthesis of nanocomposites comprising Nb₂O₅@Carbon core–shell nanoparticles (Nb₂O₅@C NPs) and reduced graphene oxide (rGO), and an analysis of their electrochemical performance with respect to various weight ratios of Nb₂O₅@C NPs to rGO (e.g., Nb₂O₅@C, Nb₂O₅@C/rGO‐70, ‐50, and ‐30). In a Na half‐cell configuration, the Nb₂O₅@C/rGO‐50 shows highly reversible capacity of ≈285 mA h g^?1 at 0.025 A g^?1 in the potential range of 0.01–3.0 V (vs Na/Na⁺). In addition, the Na‐HSC using the Nb₂O₅@C/rGO‐50 anode and activated carbon (MSP‐20) cathode delivers high energy/power densities (≈76 W h kg^?1 and ≈20 800 W kg^?1) with a stable cycle life in the potential range of 1.0–4.3 V. The energy and power densities of the Na‐HSC developed in this study are higher than those of similar Li‐ and Na‐HSCs previously reported.     

Development of a microbial time-temperature integrator system using lactic acid bacteria

A microbial time-temperature integrator (TTI) system was developed using lactic acid bacteria (Weissella koreensis) obtained from baechukimchi. Activation energy (Ea), which represents the temperature dependence of the TTI response, was calculated using the Arrhenius equation. Ea values for the color change (ΔE value), maximum specific growth rate (μ_max), and pH change of the TTI measured under different isothermal conditions (5, 10, 15 and 20°C) were 99.88, 95.91, and 93.38 kJ/mol, respectively. According to the time taken to reach the TTI endpoint by the initial inoculum level of W. koreensis (6.2, 5.5, 4.5, and 3.4 log CFU/mL), a negative correlation was observed in 63.5, 101.8, 115.1 and 166.6 h. In addition, initial bacterial counts decreased significantly up to almost 4% at 20°C in 3 months when W. koreensis viability was measured at the freezing point of the microbial TTI system (20 and ?80°C) for 1 week, 1 month, 2 months, and 3 months. However, viability was about 95% at 80°C. This microbial TTI system would be useful to monitor the quality of food with similar Ea values during storage or distribution.     

New method for low temperature fabrication of Ni–Al alloy powder for molten carbonate fuel cell applications

Lump-free Ni-5 wt% Al alloy powder was successfully prepared using an AlCl₃ activator at 400 °C under vacuum. The AlCl₃ activator served as the catalyst, lowering the fabrication temperature by 1000 °C compared with the temperature required for the conventional process. The Ni–Al alloy was formed by the following steps: the formation of NiAl by the reaction of the Ni surface with AlCl₂ or AlCl produced by the reaction between Al and AlCl₃, the formation of Ni₃Al by Al diffusion and reaction, and the formation of a Ni–Al solid solution by Al diffusion into the Ni matrix until the solubility limitation was reached. Although lowering the alloying temperature lengthens the reaction time, the time could be reduced by controlling the amount of AlCl₃. A single cell test and a creep test were also conducted using a green sheet of as-prepared Ni–Al alloy powder as an anode of a molten carbonate fuel cell (MCFC).