二元光栅照明研究

采用部分相干成象理论对二元光机照明进行了较为详细的研究。分析了二元光栅照明对分辨力，焦，照明能量和照明均匀性的影响，并通过实验研究验证了二元光栅对分辨力和焦深有较大程度的提高，同时能量损失不大。     

国际微电子专用关键设备的现状和发展趋势（考察报告）

讲述了参观Ｓｅｍｉｃｏｎ／ｗｅｓｔ９４′展览会及考察美国和西德的５个公司、１所大学所了解到的投影光刻技术、电子束曝光技术、透镜面形测试技术的发展。     

CETRAN系统中的英语词汇结构与功能

本文介绍了汉英机器翻译系统中从中间媒介语言生成英语的生成系统的词汇结构和功能，描述了生成系统各个层次之间的转换原理。为了说明清楚，在叙述中注意了列举从中间媒介中间媒介语言到目标语句的生成实例。     

Pore size control of porous silica by sol-gel process

Porous silica glass was prepared by sol-gel process from tetraethoxysilane (TEOS). The effects of solvents (water, ethanol), drying condition, heat treatment temperature on specific surface area and pore size distribution of porous silica were investigated. Gelation process accelerates with an increase of H₂O content, while retards with the increase of ethanol amount. Structure changes during heat treatment were studied by means of DTA, XRD. TEM micrographs show that the gel particles shrink after heated at 500°C, thus the average pore size decreases.     

锥形有源条半导体光放大器增益和饱和特性分析

以行波半导体光放大器速度方程为基础，采用传输矩阵方法，对锥形结构半导体光放大器的增益和饱和特性进行理论研究。讨论了不同锥形长度，不同结构时的增益和饱和特性差异。理论研究表明，锥形结构能改善半导体光放大器的偏振灵敏度。在同一锥度下，长锥形长度能提高饱和增益，降低偏振度。在进行半导体光放大器有源条结构设计时要综合考虑锥度及锥形长度的影响，以实现结构优化 。     

脱苯工艺的节能改造

焦化厂富油脱苯工艺中，管式炉法较蒸汽法节能。本溪钢铁公司焦化厂产焦１８０万ｔ／ａ的装置，其富油脱苯工艺由蒸汽法改为管式炉法后，每年可节煤７０００ｔ。     

酒精中甲醇,水在NaA沸石上吸附性能的研究

本文测定了酒精中甲醇、水单组分及二元组分的吸附等温线,并用Langmuir方程进行了拟合。在固定床动态吸附研究申测定了酒精中甲醇、水单组分及双组分吸附穿透曲线;着重考察了流速、温度、不同甲醇和水含量对双组分吸附性能的影响。对二个组分的传质机理及置换关系进行了分析探讨。     

宣钢近北庄铁矿露采边坡稳定的结构分析

以宣钢近北庄铁矿露采边坡稳定性研究为例，说细说明了岩体结构分析方法的应用。     

清平磷矿客货两用架空索道设计

系统介绍了四川清平磷矿客货两用架空索道工艺系统方案的确定及线路、上下站等主要构成部分的设备配置、方案优化与主要设备的性能、技术参数，还对系统中的安全设施、事故救护作了说明。     

Hydrothermal Synthesis of Acicular Lead Titanate Fine Powders

A pure, acicular lead titanate (PbTiO₃) fine powder with a white color has been prepared by hydrothermal synthesis. It is a new phase of PbTiO₃ with I 4 symmetry, cell parameters of a = 12.358 Å and b = 14.541 Å, and a density of 6.80 g.cm⁻³. The influences of pH (12.5 to 14.4), Pb/Ti ratio (1.0 to 1.6) in the feedstock, reaction temperature (130° to 230°C), time (0.25 to 4 h), starting materials, and additives on the formation of acicular PbTiO₃ under hydrothermal conditions have been investigated. The acicular PbTiO₃ with I 4 symmetry, referred to as the PX phase, can be converted to the perovskite-type (PE phase) of PbTiO₃ at about 605°C while its acicular morphology is essentially unchanged. The preferable conditions for preparing pure acicular PX-phase PbTiO₃ are that the pH is 13.0 to 14.0, Pb/Ti ratio is >1.3, reaction temperature is 170° to 200°C, time is 0.5 to 1.0 h, titanium butoxide (Ti[O(CH₂)₃CH₃]₄) is the starting material, and poly(vinyl alcohol) is an additive. The acicular grain of the PX phase is usually less than 100 nm in diameter and more than 1000 nm in length.