Processing of a Silicon-Carbide-Whisker-Reinforced Glass-Ceramic Composite by Microwave Heating

A calcium magnesium aluminosilicate-based glass that contained 10 wt% of silicon carbide whiskers (SiC _w ) as reinforcement was prepared by tape casting, followed by sintering either in a conventional furnace or in a microwave oven. The results were consistent with retardation of glass sintering through whisker bridging. The glass, by itself, was sintered to almost-full density at 750°C for 4 h by conventional furnace sintering; the best sintered composite, with an estimated density of ∼90%, was obtained at 800°C with a dwell time of 4 h. Sintering at a temperature of >800°C did not improve the densification but rather resulted in severe whisker oxidation. A reduced densification rate was observed for the samples that were sintered in nitrogen. By contrast, in the microwave oven, almost-full density for the glass and ∼95% of the theoretical density for the composite were obtainable at 850°C for 15 min, which represented a reduction of ∼10 h of the total processing time and a reduced SiC _w oxidation.     

Melting behavior and crystallization kinetics of poly(butylene terephthalate‐co‐diethylene terephthalate) and poly(butylene terephthalate‐co‐triethylene terephthalate) copolyesters

The melting behavior of poly(butylene terephthalate‐co‐diethylene terephthalate) and poly(butylene terephthalate‐co‐triethylene terephthalate) copolymers was investigated by differential scanning calorimetry after isothermal crystallization from the melt. Multiple endotherms were found for all the samples, and attributed to the melting and recrystallization processes. By applying the Hoffman‐Weeks' method, the equilibrium melting temperatures of the copolymers under investigation were obtained. Two distinct peaks in the crystallization exothermic curve were observed for all the samples. Both of them appeared at higher times than that of PBT, indicating that the introduction of a comonomer decreased the crystallization rate. The observed dependence of this latter on composition was explained on the basis of the content of ether–oxygen atoms in diethylene and triethylene terephthalate units, and of the different sizes of these units. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3545–3551, 2001     

Kuwanon‐L as a New Allosteric HIV‐1 Integrase Inhibitor: Molecular Modeling and Biological Evaluation

HIV‐1 integrase (IN) active site inhibitors are the latest class of drugs approved for HIV treatment. The selection of IN strand‐transfer drug‐resistant HIV strains in patients supports the development of new agents that are active as allosteric IN inhibitors. Here, a docking‐based virtual screening has been applied to a small library of natural ligands to identify new allosteric IN inhibitors that target the sucrose binding pocket. From theoretical studies, kuwanon‐L emerged as the most promising binder and was thus selected for biological studies. Biochemical studies showed that kuwanon‐L is able to inhibit the HIV‐1 IN catalytic activity in the absence and in the presence of LEDGF/p75 protein, the IN dimerization, and the IN/LEDGF binding. Kuwanon‐L also inhibited HIV‐1 replication in cell cultures. Overall, docking and biochemical results suggest that kuwanon‐L binds to an allosteric binding pocket and can be considered an attractive lead for the development of new allosteric IN antiviral agents.     

Polycarbonate‐based composites reinforced by in situ polytetrafluoroethylene fibrillation: Preparation,thermal and rheological behavior

Fibrillar reinforced composites of polytetrafluoroethylene (PTFE) and polycarbonate (PC) were prepared by in situ fibrillation of PTFE into PC matrix using twin screw extruder. Different samples were obtained by varying the relative ratio between PC and PTFE. The rheological properties of the PC/PTFE composites were found to depend on concentration of the PTFE fibrils. The melt strength analysis in nonisothermal conditions was also studied. The increase in force and decrease in drawability with increasing the PTFE content are associated with the PTFE fibrils formed in situ during the thermomechanical process in twin screw extruder. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42401.     

Porosity‐dependent properties of Nb‐doped Pb(Zr,Ti)O3 ceramics

In the present work, it is shown how the controlled porosity can be exploited to obtain a compromise between a reduced permittivity down to a few hundreds and maintaining a high tunability level as in the dense material, to fulfill requirements for tunable applications. Nb‐doped Pb(Zr,Ti)O₃ ceramics with porosity in the range 5%‐30% have been prepared by direct sintering method. X‐ray diffraction analysis and Rietveld refinement indicated a co‐existence of tetragonal and monoclinic phases in the porous ceramics. Dielectric properties revealed a gradual reduction in permittivity when increasing the porosity level, while maintaining low dielectric losses below 3%. The ferroelectric switching behavior is also influenced by the porosity level: a continuous reduction in the saturation and remnant polarization is observed with increasing porosity. The nonlinear dielectric properties of all the investigated ceramics preserve a high level of tunability in comparison with one of the dense material, irrespective of the porosity level, while zero field permittivity was decreased below 1000. An optimum behavior is found for the ceramic sample with 25% porosity, which shows a high tunability, smaller losses, and moderate dielectric constant (ε ~600).     

Maternal Flaxseed Oil During Lactation Enhances Bone Development in Male Rat Pups

Flaxseed oil is an alpha linolenic acid source important in the growth and body development stage; furthermore, this acid acts on adipose tissue and bone health. The aim of this study was to evaluate body composition, fatty acid composition, hormone profile, retroperitoneal adipocyte area and femur structure of pups at weaning, whose mothers were fed a diet containing flaxseed oil during lactation. After birth, pups were randomly assigned: control (C, n = 12) and flaxseed oil (FO, n = 12), rats whose mothers were treated with diet containing soybean or flaxseed oil. At 21 days, the pups were weaned and body mass, length, body composition, biochemical parameter, leptin, osteoprotegerin, osteocalcin, fatty acids composition, intra‐abdominal fat mass and femur structure were analyzed. FO showed (p < 0.05): higher body mass (+12 %) and length (+9 %); body fat mass (g, +45 %); bone mineral density (+8 %), bone mineral content (+55 %) and bone area (+35 %), osteocalcin (+173 %) and osteoprotegerin (+183 %). Arachidonic acid was lower (p < 0.0001), alpha‐linolenic and eicosapentaenoic were higher (p < 0.0001). Intra‐abdominal fat mass was higher (+25 %), however, the retroperitoneal adipocytes area was lower (?44 %). Femur mass (+10 %), distance between epiphyses (+4 %) and bone mineral density (+13 %) were higher. The study demonstrates that adequate flaxseed oil content during a lactation diet plays an important role in the development of pups.     

Coordination Environment of Cu(II) Ions Bound to N-Terminal Peptide Fragments of Angiogenin Protein

Angiogenin (Ang) is a potent angiogenic factor, strongly overexpressed in patients affected by different types of cancers. The specific Ang cellular receptors have not been identified, but it is known that Ang–actin interaction induces changes both in the cell cytoskeleton and in the extracellular matrix. Most in vitro studies use the recombinant form (r-Ang) instead of the form that is normally present in vivo (“wild-type”, wt-Ang). The first residue of r-Ang is a methionine, with a free amino group, whereas wt-Ang has a glutamic acid, whose amino group spontaneously cyclizes in the pyro-glutamate form. The Ang biological activity is influenced by copper ions. To elucidate the role of such a free amino group on the protein–copper binding, we scrutinized the copper(II) complexes with the peptide fragments Ang(1–17) and AcAng(1–17), which encompass the sequence 1–17 of angiogenin (QDNSRYTHFLTQHYDAK-NH₂), with free amino and acetylated N-terminus, respectively. Potentiometric, ultraviolet-visible (UV-vis), nuclear magnetic resonance (NMR) and circular dichroism (CD) studies demonstrate that the two peptides show a different metal coordination environment. Confocal microscopy imaging of neuroblastoma cells with the actin staining supports the spectroscopic results, with the finding of different responses in the cytoskeleton organization upon the interaction, in the presence or not of copper ions, with the free amino and the acetylated N-terminus peptides.     

Synthesis,Characterization, and Initial Biological Evaluation of [99mTc]Tc‐Tricarbonyl‐labeled DPA‐α‐MSH Peptide Derivatives for Potential Melanoma Imaging

α‐Melanocyte stimulating hormone (α‐MSH) derivatives target the melanocortin‐1 receptor (MC1R) specifically and selectively. In this study, the α‐MSH‐derived peptide NAP‐NS1 (Nle‐Asp‐His‐d ‐Phe‐Arg‐Trp‐Gly‐NH₂) with and without linkers was conjugated with 5‐(bis(pyridin‐2‐ylmethyl)amino)pentanoic acid (DPA‐COOH) and labeled with [^99mTc]Tc‐tricarbonyl by two methods. With the one‐pot method the labeling was faster than with the two‐pot method, while obtaining similarly high yields. Negligible trans‐chelation and high stability in physiological solutions was determined for the [^99mTc]Tc‐tricarbonyl–peptide conjugates. Coupling an ethylene glycol (EG)‐based linker increased the hydrophilicity. The peptide derivatives displayed high binding affinity in murine B16F10 melanoma cells as well as in human MeWo and TXM13 melanoma cell homogenates. Preliminary in vivo studies with one of the [^99mTc]Tc‐tricarbonyl–peptide conjugates showed good stability in blood and both renal and hepatobiliary excretion. Biodistribution was performed on healthy rats to gain initial insight into the potential relevance of the ^99mTc‐labeled peptides for in vivo imaging.