Influence of electroosmotic treatment on the hydro-mechanical behaviour of clayey silts: preliminary experimental results

Preliminary results of an investigation focused on the influence of electrokinetic treatment on the mechanical and hydraulic behaviour of clayey soils are presented. The experimental programme aims at providing a contribution to the sustainability of contaminant extraction or containment via electroosmosis. Changes in the hydraulic and mechanical properties of two illitic clayey soils, subjected to a DC electric field, were investigated. Samples of the two soils were subjected to electrokinetic filtration, for different periods of time, and under different constant loads. Afterwards, they were tested under one-dimensional compression to detect changes in stiffness and hydraulic conductivity due to the electrical treatment. After the application of a DC field for a few hours, a small reversible increment in the average soil stiffness was observed, with respect to the untreated soil, while the hydraulic conductivity was not affected substantially. Dramatic changes of the mechanical and hydraulic soil properties, correlated to changes of the soil pH, were observed following non-conditioned electrokinetic treatment with duration of the order of days.     

A disposable sensor based on immobilization of acetylcholinesterase to multiwall carbon nanotube modified screen-printed electrode for determination of carbaryl

A simple method has been devised for immobilization of acetylcholinesterase (AChE) covalent bonding to a multiwall carbon nanotube (MWNT)-cross-linked cellulose acetate composite on a screen-printed carbon electrode (SPCE) and a sensitive and disposable amperometric sensor for rapid determination of carbaryl pesticide is proposed. The immobilized enzyme was preserved on this film because of the excellent biocompatibility and non-toxicity of cellulose acetate. Based on the inherent conductive properties of the MWNT, the immobilized AChE had greater affinity for ATCl and excellent catalytic effect in the hydrolysis of ATCl. MWNT improved the interface enzymatic hydrolysis reaction and increased the amperometric response of the sensor. Under optimum conditions, the inhibition of carbaryl on AChE increased linearly with the increasing concentration of carbaryl in two ranges, from 0.01 to 0.5 μg mL⁻¹ and from 2 to 20 μg mL⁻¹, with the correlation coefficients of 0.9985 and 0.9977, respectively. The detection limit was 0.004 μg mL⁻¹ taken as the concentration equivalent to 10% decrease in signal. The sensor showed acceptable stability, accuracy and could be fabricated in batches, thus it is economic and portable. This type of disposable enzyme-based amperometric sensor has extensive application potential in environmental monitoring of pesticides.     

Influence of pencil lead hardness on voltammetric response of graphite reinforcement carbon electrodes

This work studied the voltammetric response of graphite reinforcement electrodes made of different pencil lead hardness. The studies showed that harder graphite leads, regardless of their manufacturer, are more appropriate as electrode material for voltammetric purposes due to their higher peak currents, increasing sensitivity and reproducibility, with ΔEp closer to the theoretical value for a reversible system.     

FEM model of the ohmic resistance of IP-SOFCs

In the present work, the ohmic resistance of an integrated planar-SOFC (IP-SOFC) has been evaluated by developing a model whose equations have been solved numerically through an FEM method. The model allows to estimate the distribution of voltage and current density in the cell. A comparison between simulated and experimental data of area specific resistance is reported, which shows satisfactory agreement. The mathematical model has also been used to carry out some parametric studies for optimisation purposes. Indeed, a reduction in cell pitch length and an increase in electrode thickness are predicted to lead to a reduction in ohmic losses in IP-SOFCs.     

Synthesis of polyurethane resins and its improvement on dimensional stability and finishing performances of medium‐ and small‐diameter softwoods

This study analyzed the effects of polyurethane (PU) resin treatments on surface homogeneity, dimensional stability, and finishing performances of medium‐ and small‐diameter softwoods produced in Taiwan. Two‐pack PU resins were prepared by combing short castor oil‐modified alkyd resin serving as a polyol with polymeric 4,4′‐diphenymethane diisocyanate (PMDI) serving as a hardener, by the molar ratio of NCO/OH+COOH of 1.2. Four types of short oil‐modified alkyd resins with different polyhydric alcohols (glycerin and pentaerythritol) and polybasic acids (phthalic anhydride and isophthalic acid) were synthesized. Three kinds of medium‐ and small‐diameter softwoods, including China fir, Taiwanina, and Japanese fir with a diameter of 10–15 cm were obtained from Hui‐Sun Forest Station, Taiwan. The wood coating of nitrocellulose (NC) lacquer including sanding sealer and top clear was used. Results show that the surface hardness, homogeneity, moisture excluding efficiency, and antiswelling efficiency of woods were enhanced by PU resin treatments. Among all the PU resins, the isophthalic acid and pentaerythritol‐containing PU resin (IPA‐P‐MDI) achieved the best improved efficiency on dimensional stability of woods. Results of two types of finishing procedure, i.e. NC lacquer sanding sealer plus top clear and top clear only, applied onto the PU‐treated woods revealed that the hardness, adhesion, and durability of NC lacquer films on the PU‐treated wood were superior to those of untreated one, especially for top clear finishing alone. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Shear-induced crystallization of poly(phenylene sulfide)

The crystalline morphology of poly(phenylene sulfide) (PPS) isothermally crystallized from the melt under shear has been observed by polarized optical microscope (POM) equipped with a CSS450 hot-stage. The shish–kebab-like fibrillar crystal structure is formed at a higher shear rate or for a longer shear time, which is ascribed to the tight aggregation of numerous oriented nuclei in the direction of shear. The crystallization induction time of PPS decreases with the shear time, indicating that the shear accelerates the formation of stable crystal nuclei. Under shear, the increase of spherulite growth rate results from highly oriented chains. The melting behavior of shear-induced crystallized PPS performed by differential scanning calorimetry (DSC) shows multiple melting peaks. The lower melting peak corresponds to melting of imperfect crystal, and the degree of crystal perfection decreases as the shear rate increases. The higher melting peak is related to the orientation of molecular chains. These oriented molecular chains form the orientation nuclei which have higher thermal stability than the kebab-like lamellae that are developed later. A new model based on the above observation has been proposed to explain the mechanism of shish–kebab-like fibrillar crystal formation under shear flow.     

Accelerated wear testing with a microfabricated surface to evaluate the lubrication ability of biomolecules on polyethylene

Wear of ultrahigh‐molecular‐weight polyethylene (UHMWPE) and wear‐particle‐induced osteolysis and bone resorption are the major factors causing the failure of total joint replacements. It is feasible to improve the lubrication and reduce the wear of artificial joints. We need further understanding of the lubrication mechanism of the synovial fluid. The objective of this study is to evaluate the lubricating ability of three major components in the synovial fluid: albumin, globulin, and phospholipids. An accelerated wear testing procedure in which UHMWPE is rubbed against a microfabricated surface with controlled asperities has been developed to evaluate the lubrication behavior. An analysis of the wear particle dimensions and wear amount of the tests has provided insights for comparing their lubrication performance. It is concluded that the presence of biomolecules at the articulating interface may reduce friction. A higher concentration of a biological lubricant leads to a decrease in the wear particle width. In addition, in combination with the wear results and mechanical analysis, the roles of individual biomolecules contributing to friction and wear at the articulating interface are discussed. These results can help us to identify the role of the biomolecules in the boundary lubrication of artificial joints, and further development of lubricating additives for artificial joints may be feasible. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Towards a new definition of EPOC parameters for anionic electrochemical catalysts: case of propene combustion

The electrochemical promotion of catalysis (EPOC) of propene combustion was investigated using Pt sputtered thin film on an O²⁻ conductor, 8 mol% Y₂O₃-stabilized-ZrO₂ (YSZ). In order to separate the influence of the thermal migration of the O²⁻ oxide ions from the electrolyte to the catalyst surface and the impact of an electrical polarization on the catalytic activity, several light-off experiments (cool down and heat up procedures) were successively performed under different polarizations, i.e. OCV, +2 and −2 V. These experiments have clearly shown that the presence of O²⁻ (thermally or electrochemically induced) inhibits the catalytic activity of the platinum for the propene deep oxidation. These results demonstrate the importance to define a normalized rate enhancement ratio, ρ _n , from a reference value of the catalytic rate corresponding to a Pt surface state free of O²⁻ ions.     

A strategy for the electro-organic synthesis of new hydrocaffeic acid derivatives

Electrochemical treatment processes can significantly contribute to the protection of the environment through the minimization of waste and toxic materials in effluents. From a pharmaceutical point of view and due to the existing resemblance between the electrochemical and biological reactions, it can be assumed that the oxidation mechanisms on the electrode and in the body share similar principles. In this paper, the application of electrochemical studies in the design of an environmentally friendly method was delineated for the new hydrocaffeic acid (HCA, 3,4-dihydroxy hydrocinnamic acid) derivatives synthesis at carbon electrodes in an undivided cell. In this cell, the EC mechanism reaction was involved, comprising two steps alternatively; (1) electrochemical oxidation and (2) chemical reaction. In particular, the electro-organic reactions of HCA, an important biological molecule, were studied in a water–acetonitrile (90:10 v/v) mixture in the presence of benzenesulfinic acid (3) and p-toluenesulfinic acid (4). The research included the use of a variety of experimental techniques, such as cyclic voltammetry, controlled-potential electrolysis and product spectroscopic identification.     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.