Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

Microprocessor-Based Control of an Ion Beam Deposition System

A microprocessor-based system with 32 A/D, 24 D/A, and 16 ac load controllers, has been designed and built to monitor and control an ion beam thin-film deposition system. The A/D and D/A channels have electrical isolation of 7.5 kV between channels and between input and output. The microprocessor system keeps the ion beam deposition parameters stable for extended periods of operation and it is proposed as a means to greatly simplify switching from one deposition species to another to grow thin multilayer or alloy films.     

Laboratory accreditation in the UK

Two complementary national laboratory accreditation schemes are run by the National Physical Laboratory (NPL) to provide official recognition of competent British laboratories and an assurance of quality to their customers. The first of these, the British Calibration Service (BCS), was set up in 1966 to accredit laboratories to calibrate instruments, gauges and reference materials. In 1981 the National Testing Laboratory Accreditation Scheme (NATLAS) was formed to extend the service to all kinds of testing. Both BCS and NATLAS form an integral part of the UK national measurement system and were combined to form the National Measurement Accreditation Service on 1 October 1985.     

A distribution function for double-bit upsets

It is suggested that the chord length distribution method could be useful for predicting double-bit upset rates in certain circumstances. A chord length distribution function for simultaneous path lengths in two parallelepipeds, applicable to a unidirectional flux, is derived. A proof of the system is outlined for the case under consideration     

PCR-based procedures in detection and DNA-fingerprinting of Salmonella from samples of animal origin

The usefulness of selected PCR-protocols for the detection of Salmonella in 117 samples of animal origin (17 raw minced meat, 27 raw chicken meat, 8 raw sausages, and 25 egg samples, as well as 18 poultry faecal, and caecal swabs samples) and DNA-fingerprinting typing is shown. To establish an accurate PCR-procedure for Salmonella detection the following parameters were evaluated: two pre-PCR concentration procedures, centrifugation and immunomagnetic separation (IMS) using Dynabeads anti- Salmonella; the specificity and sensitivity of 10 sets of primers; and different conditions of the amplification reaction. In light of the results obtained from the use of PCR-based procedures alone or in combination with conventional methods, the following findings can be underlined: First, IMS is more efficient than centrifugation in the recovery of Salmonella. Second, the selected IMS/PCR-detection protocol is less time-consuming (45 h) than the IMS/culture procedure (90 h), and a good concordance between them was found when the Kappa coefficient was calculated (0·87). Third, PCR-ribotyping technique showed a very low discrimination power, being able to differentiate only three profiles. Fourth, RAPD technique using specific primers supports previous works in which it was proposed as a simple and useful tool for discriminating isolates between and within serotypes. Fifth, The efficiency, rapidity, and flexibility of the PCR-protocols applied were high, and they can be performed using two PCR-programs and the same basic equipment.     

High-voltage bridge for measuring spontaneous polarization,dielectric constants,and conductivity of ferroelectric crystals

Translated from Izmeritel'naya Tekhnika, No. 9, pp. 34–35, September, 1989.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Symmetry-breaking transitions in equilibrium shapes of coherent precipitates: Effect of elastic anisotropy and inhomogeneity

We examine the symmetry-breaking transitions in equilibrium shapes of coherent precipitates in two-dimensional (2-D) systems under a plane-strain condition with the principal misfit strain components ε* _xx and ε* _yy . For systems with cubic elastic moduli, we first show all the shape transitions associated with different values of t=ε* _yy /ε* _xx . We also characterize each of these transitions, by studying its dependence on elastic anisotropy and inhomogeneity. For systems with dilatational misfit (t=1) and those with pure shear misfit (t=−1), the transition is from an equiaxed shape to an elongated shape, resulting in a break in rotational symmetry. For systems with nondilatational misfit (−1<t<1; t ≠ 0), the transition involves a break in mirror symmetries normal to the x- and y-axes. The transition is continuous in all cases, except when 0<t<1. For systems which allow an invariant line (−1≤t<0), the critical size increases with an increase in the particle stiffness. However, for systems which do not allow an invariant line (0<t≤1), the critical size first decreases, reaches a minimum, and then starts increasing with increasing particle stiffness; moreover, the transition is also forbidden when the particle stiffness is greater than a critical value.