Changes in Δ5- and Δ7-sterols during germination and seedling development ofCucurbita maximaduring germination and seedling development ofCucurbita maxima

While seeds ofCucurbita maxima contain both Δ⁵- and Δ⁷-sterols, the former, which have been described earlier, now have been found to disappear during germination. This suggests that a function exists for the Δ⁵-compounds only in the early part of the life cycle ofC. maxima, unlike most of the other higher plants studied. In contrast to the Δ⁵-sterols, the level of Δ⁷-sterols increased during germination as well as during seedling development and maturation. The period of transition between germination and seedling development appeared to be of special importance in terms of sterol changes. This period represented a surge of sterol biosynthesis with an ontogenetic shift in sterol composition from approximately equal amounts of 24α- and 24β-ethyl stereochemistry to a predominance of the former. The sterol composition of the mature plants included only about 5% of the 24β-ethylsterols. The configurational relationships were demonstrated by high resolution¹H-NMR. The sterols of the mature plants were: 25(27)-dehydrochondrillasterol, 24β-ethyl-25(27)-dehydrolathosterol, avenasterol, spinasterol, 22-dihydrospinasterol and 24ξ-methyllathosterol. Based on the changes which occurred in the relative amounts of the Δ⁷-sterols, it did not appear that the Δ⁵-components were being converted to their Δ⁷-analogs. A portion of this work was presented at the meeting of the American Oil Chemists' Society in May, 1985 in Philadelphia.     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

Long-term recovery of pressurized water reactors following a large break loss-of-coolant accident

The U.S. Nuclear Regulatory Commission recently identified a possible safety concern for pressurized water reactors. Following the reflood phase of a large break loss-of-coolant accident, long-term cooling of the reactor core may not be ensured. Specifically, the concern is that, for a pump discharge cold leg break, the loop seals in the reactor coolant pump suction piping will refill with liquid and the post-reflood steam production may depress the liquid levels in the downflow sides of the loop seals. A loop seal depression would cause a corresponding depression of the core liquid levels and possibly a fuel rod heatup in the upper core region. This paper is intended as an introduction of the safety issue that: (1) describes the important aspects of the problem, (2) provides an initial analysis of the consequences, and (3) discusses ongoing work in this area. Because the elevation of the loop seals is near the mid-core elevation in plants of Westinghouse design, the concern is greatest for those plants. There is less concern for most plants of Combustion Engineering design, and likely no concern for plants of Babcock and Wilcox design. This issue was addressed by employing both steady-state and transient systems analysis approaches. Two approaches were used because of uncertainties regarding actual reactor coolant system behavior during the post-reflood period. The steady-state approach involved the development and application of a simple computer program to investigate reactor coolant system behavior assuming quiescent post-reflood conditions. The transient systems approach involved investigating this behavior using the RELAP5/MOD2 computer code and a comprehensive RELAP5 model of a Westinghouse pressurized water reactor. The steady-state analysis indicated only a moderate fuel rod heatup is possible. The transient systems analysis indicated boiling and condensation-induced flow oscillations are sufficient to prevent fuel rod heatup. Analysis uncertainties are discussed.