基于PⅢ工控机VI测控系统远程控制研究

虚拟仪器（VI）将计算机采集测试分析引入到电子测量领域，用数字化和软件技术极大地提高了测量的灵活性。而VI远程测控系统是网络技术、通信技术一计算机虚拟技术结合的产物。远程控制技术能够使操作突破地域的限制，已在网络环境下PⅢ工控机上实现。     

直线式电机在有杆抽油设备中的应用

通过对游梁式抽油机的效率、启动特性与直线式电机驱动的有杆抽油机特性的对比，论述了直线抽油机的优越性及应用前景。     

纳米碳酸钙制备过程中添加剂作用机理探讨

采用鼓泡碳化法 ,在最佳反应温度、反应物浓度的条件下 ,考察了添加剂对产物形状及粒径大小的影响 ,得到了直径为 2 0～ 30nm、长径比在 2 0左右且分散性能良好的针状纳米碳酸钙 ,并对添加剂作用机理进行了分析。     

空投水雷空中弹道设计与仿真

文中对空投水雷的空中弹道进行了研究.在建立了六自由度的水雷空中弹道模型的基础上,在Matlab/Simulink环境下对水雷的空中弹道进行了仿真,并分析了投雷速度、水雷初始俯仰角、空中自然风对水雷空中弹道的影响.     

Colour Centres and Energy Transfer in BaF2-xClx:Eu2+ Phosphors

The optical absorption spectra of BaF2-xClx:Eu2 after ultraviolet (UV) light excitation were investigated.The differences between the absorption spectra after and before excitation (DAS) were observed.The DAS increase at both the high and the low energy side of F band in BaF2-xClx:Eu2 after 245 nm UV light excitation.The bleach effect of UV light and the absorption of electrons in the valence band may account for the former and the formation of Fa centres (association of F(Cl-) centres), whose absorption band matches the HeNe laser better, may explain the latter.In the write-in process, the transfer of electrons is via tunneling.In the readout process, the transfer of electrons captured in F(F-) and Fa centres is more likely via tunneling, and that of F(Cl-) centres is more likely via conduction band.     

沙漠生物结皮土壤发育特征的研究

通过对沙漠生物结皮层相关的土壤特性研究表明,结皮层不仅具有明显的养分富集和细粒物质的聚集作用,而且结皮层腐殖质成份的含量以及其分子结构和复杂程度也在增加。腐殖质光学特性的变化趋势明显反映了不同地区结皮层土壤发育的地带性特征。结皮层持水量明显高于沙层,并对降水再分配有一定影响。     

氨氮监测中样品蒸馏预处理对结果的影响分析

氨氮监测采用预蒸馏处理后，比色测定结果明显偏低。在样品预蒸馏处理过程中，硼酸作为吸收液，使显色时溶液pH值偏低，导致显色不充分是其主要影响因素。通过采取增加显色剂加入量的方法，解决了显色pH值偏低的问题，得到满意的测定结果。     

Frequency shift keyed narrowband interference rejection: optimal exponential weighting factor for the RLS algorithm

Cochannel narrowband interference can limit the performance of direct sequence spread spectrum (DSSS) and high frequency (HF) systems. Narrowband interference (NBI) can be single tone, chirped or frequency shift keyed (FSK) in nature and numerous techniques for its removal have been proposed. Linear adaptive prediction filters based on autoregressive modelling have been suggested owing to their ability to perform in a non-stationary environment. In the FSK narrowband interference case, adaptive filters are susceptible to excess residual errors owing to instantaneous frequency step changes and the finite convergence time required for the filter to adapt to a new interference frequency. The signal degradation owing to this type of interference becomes greater in high SNR regimes and has been found to be a function of the frequency parameters of the FSK interference signal. The paper discusses the convergence and frequency tracking properties of the recursive least squares (RLS) adaptive lattice filter using a posteriori estimation errors in the presence of FSK narrowband interference. An optimal exponential weighting factor that balances convergence time and steady state error is derived for this case of NBI. Results are compared to those of a previously proposed fast converging minimum frequency error (FCMFE) RLS lattice filter.     

CuMgAl类水滑石的制备和表征

用盐-碱制备法合成了CuMgAl三元类水滑石化合物。探讨了原料配比、合成方式、水热处理温度和时间对合成过程的影响,筛选出合成HTLcs的适宜条件,并对HTLcs结构的热稳定性进行初步研究。结果表明,制备HTLcs主要取决于pH值,同时由于Cu2+的姜-太勒效应,合成结构单一的CuMgAl类水滑石要求原料配比中n(Cu)∶n(Mg)不得超过1.0,CuMgAl-HTLcs热稳定性较差,300℃焙烧2h结构破坏,600℃开始烧结,在300~500℃之间,随焙烧温度提高所得复合氧化物比表面积增大,最高可达200 m2/g。     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.