High-Throughput Determination of Interdiffusion Coefficients for Co-Cr-Fe-Mn-Ni High-Entropy Alloys

In this report, a combination of the diffusion multiple technique and the recently developed pragmatic numerical inverse method was employed for a high-throughput determination of interdiffusivity matrices in Co-Cr-FeMn-Ni high-entropy alloys (HEAs). Firstly, one face-centered cubic (fcc) quinary Co-Cr-Fe-Mn-Ni diffusion multiple at 1373 K was carefully prepared by means of the hot-pressing technique. Based on the composition profiles measured by the field emission electron probe micro analysis (FE-EPMA), the composition-dependent interdiffusivity matrices in quinary Co-Cr-Fe-Mn-Ni system at 1373 K were then efficiently determined using the pragmatic numerical inverse method. The determined interdiffusivities show good agreement with the limited results available in the literature. Moreover, the further comparison with the interdiffusivities in the lower-order systems indicates the sluggish diffusion effect in Co-Cr-Fe-Mn-Ni HEAs, which is however not observed in tracer diffusivities. In order for the convenience in further analysis, a generalized transformation relation among interdiffusivities with different dependent components in multicomponent systems was finally derived.     

Weldability and microstructural variations in weldments of Ti-5Ta-1.8Nb alloy

The successful replacement of the present generation of corrosion-resistant materials (nitric acid-grade stainless steel and Ti) by Ti-5Ta-1.8Nb, which has better corrosion resistance, depends on its weldability characteristics. This article presents the results of a study on the fabrication, qualification, and microstructural characterization of the welds. Welding was carried out using the direct current electrode negative (DCEN) polarity tungsten inert gas (TIG) (manual) welding method with high-purity Ar shielding. Testing was carried out as per the ASME standard (section IX, welding and brazing). Qualification tests found that the weldment met the required properties. The weldment showed heterogeneous microstructures, which are rationalized based on differences in phase transformation mechanisms that are dictated by the thermal cycles experienced by various microscopic regions. The results, described in this article, confirm that the weldability of the developmental Ti-Ta-Nb alloy is excellent. A preliminary evaluation of the corrosion behavior of the welds showed rates comparable to that of the base metal, establishing that this alloy could be considered as an alternative material for use in highly corrosive environments.     

Template-free hydrothermal synthesis of single-crystalline SnO<Subscript>2</Subscript> nanocauliflowers and their optical properties

Large-scale single-crystalline SnO₂ nanocauliflowers were successfully synthesized using a hydrothermal growth method without any template. The samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and selected area electron diffraction (SAED). FE-SEM images show that the as-grown SnO₂ nanocauliflowers are constructed of tetragonal prisms with a width of 500–600 nm. XRD, EDS, and SAED results indicate that the as-grown SnO₂ nanocauliflowers are single crystalline with the tetragonal rutile crystalline structure. The growth mechanism of SnO₂ nanocauliflowers is also preliminarily discussed on the basis of different Sn(OH)₆²⁻ concentrations, and it is found that Sn(OH)₆²⁻ concentration plays an important role in determining the shape of the prepared SnO₂. Room temperature photoluminescence was further carried out on SnO₂ nanocauliflowers to investigate their optical properties. An intense blue luminescence centered at a wavelength of 424 nm is observed in the as-grown SnO₂ nanocauliflowers.     

A study of job shop standard setup time quota

For the multi-item and small lot size production mode and single machine job shop scheduling sequence independent setup time, many setup times are difficult to estimate accurately, which influences the ability to achieve accurate production cycles and costs of products. The survey shows that the length of the setup time depends on the level of employee’s knowledge. Therefore, a method for determining the standard setup time quota based on the level of employees’ knowledge is proposed. First, an evaluation index system for the level of employee’s knowledge is built; the level of employee’s knowledge is estimated by the masses and experts fuzzy comprehension evaluation and entropy method. Second, the range and definition of the level of employees’ knowledge index are developed. Third, the relational model of the employee’s knowledge level and the level of employees’ knowledge index is constructed through the least squares method. Finally, an example application is presented to verify the feasibility and effectiveness of the proposed model.     

Preparation of Mo2C by MPCVD and Its Photocatalytic Properties

Mo2C was prepared by microwave plasma chemical vapor deposition(MPCVD)technique with the power of 800 W and pressure of 18 kPa. Compared with traditional prepar...     

A Flower-like In2O3 Catalyst Derived via Metal–Organic Frameworks for Photocatalytic Applications

The most pressing concerns in environmental remediation are the design and development of catalysts with benign, low-cost, and efficient photocatalytic activity. The present study effectively generated a flower-like indium oxide (In₂O₃-MF) catalyst employing a convenient MOF-based solvothermal self-assembly technique. The In₂O₃-MF photocatalyst exhibits a flower-like structure, according to morphology and structural analysis. The enhanced photocatalytic activity of the In₂O₃-MF catalyst for 4-nitrophenol (4-NP) and methylene blue (MB) is likely due to its unique 3D structure, which includes a large surface area (486.95 m² g⁻¹), a wide spectrum response, and the prevention of electron–hole recombination compared to In₂O₃-MR (indium oxide-micro rod) and In₂O₃-MD (indium oxide-micro disc). In the presence of NaBH₄ and visible light, the catalytic performances of the In₂O₃-MF, In₂O₃-MR, and In₂O₃-MD catalysts for the reduction of 4-NP and MB degradation were investigated. Using In₂O₃-MF as a catalyst, we were able to achieve a 99.32 percent reduction of 4-NP in 20 min and 99.2 percent degradation of MB in 3 min. Interestingly, the conversion rates of catalytic 4-NP and MB were still larger than 95 and 96 percent after five consecutive cycles of catalytic tests, suggesting that the In₂O₃-MF catalyst has outstanding catalytic performance and a high reutilization rate.     

Combination of Sanguisorbigenin and Conventional Antibiotic Therapy for Methicillin-Resistant Staphylococcus aureus: Inhibition of Biofilm Formation and Alteration of Cell Membrane Permeability

Methicillin-resistant Staphylococcus aureus (MRSA) infection is challenging to eradicate because of antibiotic resistance and biofilm formation. Novel antimicrobial agents and alternative therapies are urgently needed. This study aimed to evaluate the synergy of sanguisorbigenin (SGB) isolated from Sanguisorba officinalis L. with six conventional antibiotics to achieve broad-spectrum antibacterial action and prevent the development of resistance. A checkerboard dilution test and time-to-kill curve assay were used to determine the synergistic effect of SGB combined with antibiotics against MRSA. SGB showed significant synergy with antibiotics and reduced the minimum inhibitory concentration of antibiotics by 2–16-fold. Biofilm inhibition assay, quantitative RT-PCR, crystal violet absorption, and transmission electron microscopy were performed to evaluate the synergy mechanism. The results indicated that SGB could inhibit biofilm formation and alter cell membrane permeability in MRSA. In addition, SGB was found to exhibit quite low cytotoxicity and hemolysis. The discovery of the superiority of SGB suggests that SGB may be an antibiotic adjuvant for use in combination therapy and as a plant-derived antibacterial agent targeting biofilms.     

Comparing the Effects of Microwave and Conventional Heating Methods on the Evaporation Rate and Quality Attributes of Pomegranate (<Emphasis Type="Italic">Punica granatum</Emphasis> L.) Juice Concentrate

Pomegranate juice was concentrated by conventional heating and microwave heating at different operational pressures (12, 38.5, and 100 kPa), and their effects on evaporation rate and quality attributes of concentrated juice were investigated. The final juice concentration of 40° Brix was achieved in 140, 127, and 109 min at 100, 38.5, and 12 kPa, respectively, by using conventional heating. Applying microwave energy decreased required times to 118, 95, and 75 min. The changes in color, anthocyanin content, and antioxidant capacity during concentration processes were investigated. L*, a*, and b* parameters were measured to estimate the intensity of color loss. All Hunter color parameters decreased with time. Results showed that the degradation of color, anthocyanins, and antioxidant activity were more important in conventional heating compared to microwave heating method. Degradation rates increases by increasing process pressure. A first-order kinetics model was applied to modeling changes in total solid content, anthocyanin content, and antioxidant capacity.     

Application of the Extended Langmuir Model for the Determination of Lyophobicity of 1-Propanol in Acetonitrile

Surface tensions (σ) of binary liquid mixtures of acetonitrile (ACN) with 1-propanol (PrOH) were measured over the entire composition range at eight different temperatures, 278.15 K, 283.15 K, 288.15 K, 293.15 K, 298.15 K, 303.15 K, 308.15 K, and 313.15 K. The lyophobicities (β) of the surfactant PrOH relative to that of ACN as well as the surface mole fractions () of PrOH at various temperatures were derived using the extended Langmuir model (Langmuir 17, 4261, 2001). The β values indicate the greater affinity of PrOH for the surface, and this trend slightly increases with rising temperature. The determined values indicate that the surface concentration of PrOH is always higher than its bulk concentration and consequently confirm that the surface is enriched with PrOH.     

Coating of TiO2 nanoparticles with PbS thin films and preparation of PbS nanoparticles using a one-pot sonochemical reaction under the multibubble sonoluminescence conditions

Preparations of PbS-coated titanium dioxide (TiO₂) and lead sulfide (PbS) nanoparticles under ultrasonic field at the multibubble sonoluminescence (MBSL) conditions were tested in water solutions. Under the optimal MBSL conditions (20 kHz and 220 W power input), PbS nanoparticles (diameter = 40-50 nm) were prepared by treating lead nitrate and thioacetamide for 20 min in water solutions. The size of PbS nanoparticles was found to be easily increased to about 90 nm in diameter by increasing the reactant concentration twice. A similar sonochemical reaction with TiO₂ nanoparticles (about 20-30 nm in diameter) gave rise to PbS-coated TiO₂ nanoparticles with a core/shell structure. The PbS thin film coating was quite uniform and the average coating depth of PbS on the TiO₂ nanoparticles was about 2-3 nm under the described conditions. It is interesting to note that the coating depth was found to be controlled to 2-10 nm range by increasing the amounts of reactants for Pb and S twice with a sonication time of 30 min.