Liquid cooling of bright LEDs for automotive applications

With the advances in the technology of materials based on GaN, high brightness white light emitting diodes (LEDs) have flourished over the past few years and have shown to be very promising in many new illumination applications such as outdoor illumination, task and decorative lighting as well as aircraft and automobile illuminations. The objective of this paper is to investigate an active liquid cooling solution of such LEDs in an automotive headlights application. The thermal design from device to board to system level has been carried out in this research. Air cooling and passive liquid cooling methods were investigated and excluded as unsuitable, and therefore an active liquid cooling solution was selected. Several configurations of the active liquid cooling system were studied and optimisation work was carried out to find an optimum thermal performance.     

Removal kinetics of organic compounds and sum parameters under field conditions for managed aquifer recharge

Managed aquifer recharge (MAR) provides efficient removal for many organic compounds and sum parameters. However, observed in situ removal efficiencies tend to scatter and cannot be predicted easily. In this paper, a method is introduced which allows to identify and eliminate biased samples and to quantify simultaneously the impact of (i) redox conditions (ii) kinetics (iii) residual threshold values below which no removal occurs and (iv) field site specifics. It enables to rule out spurious correlations between these factors and therefore improves the predictive power. The method is applied to an extensive database from three MAR field sites which was compiled in the NASRI project (2002-2005, Berlin, Germany). Removal characteristics for 38 organic parameters are obtained, of which 9 are analysed independently in 2 different laboratories. Out of these parameters, mainly pharmaceutically active compounds (PhAC) but also sum parameters and industrial chemicals, four compounds are shown to be readily removable whereas six are persistent. All partly removable compounds show a redox dependency and most of them reveal either kinetic dependencies or residual threshold values, which are determined. Differing removal efficiencies at different field sites can usually be explained by characteristics (i) to (iii).     

A case of sporadic ovine mastitis caused by Listeria monocytogenes and its effect on contamination of raw milk and raw-milk cheeses produced in the on-farm dairy

We describe a case of listerial mastitis in a flock of 130 sheep. The animals were housed at a farm where the bulk raw ewe milk was processed to produce raw milk soft cheese. List. monocytogenes was shed from the right mammary complex. Shedding was observed over a period of 99 d. A mean level of 4-56 x 10(4) cfu (colony forming units) Listeria monocytogenes/ml was recovered from the raw milk originating from the infected udder. The numbers ranged from 9 x10(1) to 2.95 x 10(5). The bulk milk was contaminated by approx. 5.7 x 10(3) cfu/ml. In the cheese product, 2.0 x 10(2) cfu List. monocytogenes/g were constantly detectable for a period of 7 d post manufacture. The starter culture used for coagulation had a pivotal influence on the behaviour of List. monocytogenes during cheesemaking. Using the same mesophilic buttermilk culture as used by the farmer allowed numbers of Listeria to increase 60-fold within 12 h owing to a delayed acidification of the bulk milk. Addition of a thermophilic yogurt culture reduced the numbers of Listeria within 8 h of incubation.     

Study on the influence of electron beam irradiation on the thermal,mechanical, and rheological properties of ethylene‐octene copolymer with high comonomer content

Ethylene‐octene copolymer (EOC) was irradiated using electron beam irradiation at different dosages (30, 60, 90, and 120 kGy). Effect of irradiation dosage on thermal and mechanical properties was studied. When compared to low density polyethylene, EOC exhibited higher degree of crosslinking reflected in increased gel content, higher elastic modulus (G′), and lower tan δ obtained by rheology measurement at 150°C. Crosslinking caused improvement in high‐temperature creep and room temperature and also elevated temperature elastic properties. Differential scanning calorimetry revealed that e‐beam irradiation has caused a gradual reduction in crystallinity and a presence of a fraction with higher melting temperature. In the case of EOC, as the extent of crosslinking increased, stress at break showed an increasing trend whereas irradiation dosage had an inverse effect on elongation at break. Radiation dosage has positive effect on thermal stability estimated by thermogravimetric analysis. After 30 min of thermal degradation at 220°C, slightly higher C?O peak for crosslinked sample was found by Fourier transform infrared spectroscopy while for room temperature samples no C?O peak was detected. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

AHP method application in selection of appropriate material handling equipment in selected industrial enterprise

Wireless Networks - The paper deals with handling equipment that can be used to transport/handle the final products in a selected industrial enterprise. The suitable handling equipment listed in...     

Managerial Skills for Innovation Support

Mobile Networks and Applications - New solutions are more and more needed due to the fact that new trends in technology, communication, global knowledge, new managerial approaches, building new...