Enhanced light output in nitride-based light-emitting diodes by roughening the mesa sidewall

In this letter, we will report on a nitride-based light emitting diode with a mesa sidewall roughening process that increases light output power. The fabricated GaN-based light-emitting diode (LED) wafers were first treated through a photoelectrochemical (PEC) process. The Ga/sub 2/O/sub 3/ layers then formed around the GaN : Si n-type mesa sidewalls and the bottoms mesa etching regions. Selective wet oxidation occurred at the mesa sidewall between the p- and the n-type GaN interface. The light output power of the PEC treated LED was seen to increase by about 82% which was caused by a reduced index reflectance of GaN-Ga/sub 2/O/sub 3/-air layers, by a rough Ga/sub 2/O/sub 3/ surface, by a microroughening of the GaN sidewall surface, and by a selective oxidation step profile of the mesa sidewall that increases the light-extraction efficiency from the mesa sidewall direction. Consequently, this wet PEC treated process is suitable for high powered nitride-based LEDs lighting applications.     

A new method for producing high melt strength polypropylene with reactive extrusion

A high‐melt‐strength polypropylene (HMSPP) was prepared using a twin‐screw reactive extruder from a commercial isotactic polypropylene through two stages, first, maleic anhydride is grafted to polypropylene to obtain a maleic anhydride‐grafted polypropylene (PP‐g‐MA), and then the grafted polymer is reacted with epoxy to extend the branched chain. Fourier transformed infrared spectroscopy indicated that maleic anhydride was grafted on polypropylene and reacted with epoxy. Melt flow rate and sag resistance test showed that the melt strength of the HMSPP improved considerably. Differential scanning calorimetry test showed that the long chain branches (LCBs) act as a nucleating agent in the crystallization of the HMSPP, which leads to a high crystallization temperature and crystallinity. Furthermore, the LCB efficiency of the HMSPP can also be calculated by analyzing its rheological property. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

赴日无线电监测技术考察报告

首先介绍了日本总务省关东综合通信局电波监理部的情况，然后对日本安立公司生产的RR510A型无线电监测接收机和技术参数以及MS8609A型数字移动无线发射机测试仪的功能进行了分析和介绍。     

On a three-dimensional axisymmetric boundary-value problem of nonlinear elastic deformation: Asymptotic solution and exponentially small error

In this paper, we study a three-dimensional axisymmetric boundary-value problem of a slender cylinder composed of a nonlinearly elastic material subjected to an axial force. Starting from the field equations, after a transformation and proper scalings, we identify a small variable and two small parameters, which characterize the present problem. Then, by an approach involving compound series-asymptotic expansions, a nonlinear ODE is derived, which governs the axial strain (the first-term in the series expansion). By imposing the zero radial displacement conditions at two ends, we manage to get the analytical solution of the axial strain, from which all other physical quantities can be deduced and thus the three-dimensional displacement field can be determined. Graphical results are presented, which show that there are two boundary layers near the two ends while the middle part is in a state of almost uniform extension. The asymptotic structure of the analytical solution is derived, which offers clear explanations to the structure of the deformed configuration and shows that the thickness of both boundary layers is of the order of the radius. We also point out the relevance of the present results to the St. Venant’s problem. In particular, we obtain the explicit uniformly-valid exponentially small error term, when the obtained deformed configuration is compared to the configuration of a uniform extension.     

Al_(10)Zn_(2.9)Mg_(1.7)Cu超高强铝合金的喷射成形制备研究

采用喷射成形技术制备了Al1 0 Zn2 .9Mg1 .7Cu高强高韧铝合金沉积坯件 ,研究了喷射成形制备过程中各工艺参数对沉积坯件的成形性、显微组织、致密度的影响 ,确定了适当的工艺参数 ,研究了沉积坯件的热挤压及热处理工艺 ,对材料的组织进行了分析并对不同状态的材料性能进行了比较。研究结果表明 :当喷射成形工艺参数合理时 ,沉积坯件具有良好的成形性与致密度 ,在随后的热挤压过程中 ,通过较低的挤压比即可使材料达到全致密 ;通过对合金进行适当的热处理 ,材料的极限抗拉强度达到 810MPa ,同时延伸率保持在 8%～ 11% ,该材料是一种理想的轻质高强结构材料。     

The changes of lipid metabolism and hemorrheology in intrahepatic cholestasis during pregnancy

OBJECTIVE: To identify the influence of the increased level of serum cholyglycine (CG) on lipid metabolism and hemorrheology in patients with intrahepatic cholestasis during pregnancy (ICP). METHODS: The concentrations of serum CG, total cholesterol (CH), triglycerides (TG), high density lipoprotein-cholesterol (HDL-C), low density lipoprotein-cholesterol (LDL-C), high shear and low shear of blood specific viscosity (HS and LS), plasma specific viscosity (PV) and hematocrit (HCT) were measured in 68 cases of primiparas with single pregnancy and 30 healthy nonpregnant women respectively. The group of ICP was composed of 35 cases with CG > 6 mumol/L, the group of normal pregnancy, 33 cases with CG < 6 mumol/L. RESULTS: The means of CG and the lipidic parameters in the two pregnant groups were significantly higher than those in the non-pregnancy group (P < 0.02-0.001) except the means of HDL-C between the groups of ICP and non-pregnancy. The levels of LDL-C, LDL-C/HDL-C, LS, PV and HCT in the ICP were significantly higher than those in the normal pregnancy group (P < 0.02-0.001). CONCLUSIONS: There are significant changes of lipid metabolism and hemorrheology in patients with ICP. However, these changes could be corrected after pregnancy termination, when the level of serum CG returned to normal. The results suggest that the pathophysiologic changes of ICP are associated with increased level of serum CG.     

智能工作站主机的MMPIS实验模型研究──一个全互连式结构MMPIS硬件环境的设计与实现

本文介绍中日国际合作开发研究的Ａ１型智能网（Ａ１型ＩＮ）智能工作站（ＩＷ）主机的并行推理硬件结构的实验模型设计与实现，给出了一种并行推理硬件支持环境实现方案和该方案在实现中若干问题的解决方法。     

硬件握手双向选通型串行通信共享器的设计

本文介绍了ＩＢＭ－ＰＣ系列计算机通过ＲＳ－２３２Ｃ串行口与多个单片微机组成的分布式系统中一种可双向选通串行通信共享器的设计方法。给出通信共享器的设计电路；并对电路工作原理进行了详细剖析。