A novel experimental technique to determine the heat transfer coefficient between the bed and particles in a downer

A novel method for directly measuring the temperature history of mobile hot ferromagnetic particles (steel particles), substituting for reacting particles, in a binary-solid (reacting particles and inert particles) downflow is introduced. The temperature history of the hot steel particles can be obtained by measuring the temperature of the particles at different axial positions using magnetic fields that can separate the steel particles from other bed materials immediately and easily. Employing the magnetic marking method, magnetic sensors were used to detect the change in magnetic flux density in a given magnetic field, and the residence time of the steel particles was also measured. The cross-sectional averaged particle-to-bed heat transfer coefficients were calculated from the experimental results using simple heat balance equations. The measured temperature data have a relatively wide error range; however, the average temperature curves derived from the average particle-to-bed heat transfer coefficients agreed with the temperature plots. Therefore, the experimental method of this study is applicable to the measurement of the particle temperature in a binary-solid downflow. The results showed that there is strong correlation between the particle-to-bed heat transfer coefficients and normalized collision frequency under the laminar gas flow conditions.     

Development of an energy-binned photon-counting detector for X-ray and gamma-ray imaging

The aim of this study is to develop an energy-binned photon-counting (EBPC) detector that enables us to provide energy information of x-rays with a reasonable count statistics. We used Al-pixel/CdTe/Pt semiconductor detectors, which had an active area of 8 mm×144 mm and consisted of 18 modules aligned linearly. The size of a CdTe detector module was 8 mm×8 mm and the thickness of the CdTe crystal was 1 mm. Each module consisted of 40×40 pixels and the pixel size was 200 μm×200 μm. We applied the bias voltage of −500 V to the Pt common electrode. The detector counted the number of x-ray photons with four different energy windows, and output four energy-binned images with pixel depths of 12, 12, 11 and 10 bits at a frame rate of 1200 Hz (300 Hz×4 energy bins). The basic performance of the detector was evaluated in several experiments. The results showed that the detector realized the photon counting rate of 0.4×10⁶ counts/sec/pixel (10⁷ counts/sec/mm²), energy resolution 4.4% FWHM at 122 keV. The integral uniformity of the detector was about 1% and the differential uniformity was about 1%. In addition, the image quality was examined with a resolution chart and step-wedge phantoms made of aluminum and polymethyl methacrylate. And we compared the quality of an acquired image with that acquired with an energy integration detector. The results of these experiments showed that the developed detector had desirable intrinsic characteristics for x-ray photon counting imaging.     

The temperature dependence of luminescence from a long-lasting phosphor exposed to ionizing radiation

The temperature dependence of luminescence from a long-lasting phosphor (LLP), SrAl₂O₄ : Eu²⁺,Dy³⁺, exposed to ionizing radiation has been measured to understand the LLP luminescence mechanism. Evaluation of the decay constants of the LLP exposed to -, β- or γ-rays at temperatures from 200 to 390 K showed that the decay constant is divided into four components ranging from 10⁻⁴ to 10⁻¹ s⁻¹ with activation energies of 0.02–0.35 eV.

Total luminous intensity from the LLP with changing irradiation temperature has its maximum value around the room temperature. Irradiation at elevated temperature (390 K) has the total luminescence pattern with monotonous decrease as temperature rises. As a result of evaluating the temperature dependence of luminescence, the luminescence mechanism is considered as follows:

Full-size image

 

Chemically Tuned p‐ and n‐Type WSe2 Monolayers with High Carrier Mobility for Advanced Electronics

Monolayers of transition metal dichalcogenides (TMDCs) have attracted a great interest for post‐silicon electronics and photonics due to their high carrier mobility, tunable bandgap, and atom‐thick 2D structure. With the analogy to conventional silicon electronics, establishing a method to convert TMDC to p‐ and n‐type semiconductors is essential for various device applications, such as complementary metal‐oxide‐semiconductor (CMOS) circuits and photovoltaics. Here, a successful control of the electrical polarity of monolayer WSe₂ is demonstrated by chemical doping. Two different molecules, 4‐nitrobenzenediazonium tetrafluoroborate and diethylenetriamine, are utilized to convert ambipolar WSe₂ field‐effect transistors (FETs) to p‐ and n‐type, respectively. Moreover, the chemically doped WSe₂ show increased effective carrier mobilities of 82 and 25 cm² V^?1s^?1 for holes and electrons, respectively, which are much higher than those of the pristine WSe₂. The doping effects are studied by photoluminescence, Raman, X‐ray photoelectron spectroscopy, and density functional theory. Chemically tuned WSe₂ FETs are integrated into CMOS inverters, exhibiting extremely low power consumption ( ≈ 0.17 nW). Furthermore, a p‐n junction within single WSe₂ grain is realized via spatially controlled chemical doping. The chemical doping method for controlling the transport properties of WSe₂ will contribute to the development of TMDC‐based advanced electronics.     

Synthesis of Nanohole‐Structured Single‐Crystalline Platinum Nanosheets Using Surfactant‐Liquid‐Crystals and their Electrochemical Characterization

Nanohole‐structured single‐crystalline Pt nanosheets have been synthesized by the borohydride reduction of Na₂PtCl₆ confined to the lyotropic liquid crystals (LLCs) of polyoxyethylene (20) sorbitan monooleate (Tween 80) with or without nonaethylene‐glycol (C₁₂EO₉). The Pt nanosheets of around 4–10 nm in central thickness and up to 500 nm or above in diameter have a number of hexagonal‐shaped nanoholes ∼1.8 nm wide. High‐resolution electron microscope images of the nanosheets showed atomic fringes with a spacing of 0.22 nm indicating that the nanosheets are crystallographically continuous through the nanoholed and non‐holed areas. The inner‐angle distributions for the hexagonal nanoholes indicate that the six sides of the nanoholes are walled with each two Pt (111), Pt (1 1) and Pt (010) planes. The formation mechanism of nanoholed Pt nanosheets is discussed on the basis of structural and compositional data for the resulting solids and their precursory LLCs, with the aid of similar nanohole growth observed for a Tween 80 free but oleic acid‐incorporated system. It is also demonstrated that the nanoholed Pt nanostructures loaded on carbon exhibit fairly high electrocatalytic activity for oxygen reduction reaction and a high performance as a cathode material for polymer‐electrolyte fuel cells, along with their extremely high thermostability revealed through the effect of electron‐irradiation.     

具有缺陷和应力限值的预应力钢支撑柱屈曲性能

通过预应力支撑加固的钢柱,一般增加了轴向抗压强度。过去,十分强调获得更高的临界屈曲荷载,然而,后屈曲性能是结构安全性和功能的重要保证。对具有几何缺陷和与可能的材料失效相关的应力极限的支撑柱的屈曲性能进行检验。考虑有几何缺陷支撑柱的屈曲性能,采用Rayleigh-Ritz方法对几何非线性模型公式化,并通过有限元方法进行验证。研究显示：对于承受最高临界荷载的预应力状态,系统对有几何缺陷的柱更为敏感。对某一给定形状结构,实际的最大荷载似乎随着预应力的增加而增加。研究建议：最佳的预应力取值应该大于基于传统方法的线性分析的结果。     

Effects of cold rolling and annealing on the structure of γ″ precipitates in a Ni-18Cr-16Fe-5Nb-3Mo alloy

A Ni-18Cr-16Fe-5Nb-3Mo alloy (a modified alloy 718, referred to herein as 718M), in which the γ″ phase is the only precipitation-strengthening phase, was made by substituting most of the aluminum and titanium in INCONEL 718 with niobium. The specimens of alloy 718M were solid-solution heat treated, aged at 1033 to 1073 K for up to 360 ks, and cold rolled to a reduction of 10 to 15 pct at room temperature. After subsequent annealing heat treatments, at the same temperatures used for aging, the morphological and structural changes of the γ″ precipitates were investigated by transmission electron microscopic observation using carbon extraction replicas. Although stacking faults were not noticed in the γ″ precipitates extracted from the aged 718M alloy, stacking faults introduced in the {112} _γ″ planes by cold rolling of the samples were confirmed. The stripelike contrast due to the stacking faults becomes less clear with increasing annealing time. With longer annealing times, necking occurs between the stripes, which eventually separate into plural particles. The selected-area electron diffraction (SAED) patterns of the cold-rolled and annealed particles show that the metastable γ″ precipitates with stacking faults are transformed gradually into a stable δ phase. In this article, we discuss the basis of morphological and structural changes in detail. INCONEL is a trademark of INCO Alloys International, Inc., Huntington, WV.     

A new choleretic effect of folinic acid

BACKGROUND/AIMS: In the chemotherapy of recurrent gastric cancer with 5-fluorouracil and folinic acid, an interesting phenomenon, the reduction of jaundice and improvement of liver function, was observed. The aim of this study was to investigate the mechanism of this phenomenon, and to confirm a choleretic effect of folinic acid. METHODOLOGY: The bile duct of anesthetized rats was catheterized, and bile was collected. Bile volume and total bile acid production following intraperitoneal administration of folinic acid were determined and compared to those of control rats. RESULTS: Both bile volume and total bile acid production increased following intraabdominal administration of folinic acid. CONCLUSIONS: Folinic acid has a newly described pharmacologic effect of stimulating bile acid-dependent choleresis. It is possible that folinic acid may become a new drug for the treatment of jaundice or for the improvement of overall liver function.     

Genetic polymorphisms of cytochrome P4502E1 related to the development of alcoholic liver disease

BACKGROUND/AIMS: Because heavy drinkers do not always develop alcoholic liver disease (ALD), genetic factors may be involved. Cytochrome P4502E1 is the main enzyme that oxidizes ethanol in the non-alcohol dehydrogenase pathway. Recently, the presence of genetic polymorphisms of this enzyme was confirmed. In the present study, the genotypes of P4502E1 were analyzed in patients with or without ALD. METHODS: After extraction of DNA from white blood cells, genotypes of P4502E1 were determined by restriction fragment length polymorphisms using two endonucleases. The genotypes were separated into three types: type A, type C (homozygous for the c1 or c2 gene), and type B (heterozygous for both genes). RESULTS: In 50 patients with ALD, the prevalence of type A was 16% and that of the c2 gene was 84%. The genotypes in 10 heavy drinkers without ALD were all type A. In 34 patients with non-alcoholic liver disease and in 88 patients without hepatobiliary disease, the prevalence of type A was 65% and 71%, respectively, indicating a significantly higher prevalence of the c2 gene in ALD. In healthy nonalcoholics, the prevalence of type A was 62%-68%. CONCLUSIONS: These results suggest that polymorphisms of P4502E1 may be related to the development of ALD.