Adsorption and desorption properties of cationic polyethylene film gels to organic anions and their regeneration

An investigation was undertaken on the adsorption and desorption properties of 2‐(dimethylamino)ethyl methacrylate grafted polyethylene (PE‐g‐PDMAEMA) films to anionic dye anions with one to three sulfonic groups in response to pH and temperature changes. The amounts of dye anions adsorbed on the PE‐g‐PDMAEMA films passed through the maximum values at about pH 3 because of an increase in the protonation of dimethylamino groups caused by a decrease in the pH value. The amounts of adsorbed dye anions decreased below pH 3 because the ionic strength increased with the addition of HCl to adjust the initial pH values of the aqueous dye solutions. The amounts of adsorbed dye anions decreased with an increase in the number of sulfonic groups in the dye molecules at the same pH value because electrostatic repulsion was generated between free sulfonic groups of the dye anions adsorbed onto the PE‐g‐PDMAEMA films and free dye anions in the medium. A large number of dye anions adsorbed were desorbed from the PE‐g‐PDMAEMA film with initial pH values above 11.0. The cyclic processes of adsorption at pH 3.0 and desorption at pH 11.0 were repeated without considerable fatigue. The PE‐g‐PDMAEMA films showed practically regenerative adsorption and desorption behavior in response to the pH changes. In addition, when the dye‐anion‐adsorbed PE‐g‐PDMAEMA films were alternately immersed in water at two different temperatures, dye anions were desorbed in water at higher temperatures without any chemical agents because of the deprotonation of dimethylamino groups and thermosensitive contraction of grafted PDMAEMA chains. These results indicate that PE‐g‐PDMAEMA films can be applied as regenerative ion‐exchange membranes for adsorption and desorption processes of anionic compounds in response to the pH and temperature. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 381–391, 2006     

Proton conducting acid-base mixed materials under water-free condition

In recent years, a lot of attentions have been paid for a development of water-free polymer electrolyte membranes fuel cells (PEMFC) at intermediate temperatures (above 100 °C) because of many technological advantages of higher temperature operation. However, the proton conductivity of conventional polymer membranes under water-free condition is usually very low and the polymeric membranes are not stable at higher temperatures. So, the development of non-hydrous proton conducting membrane under water-free condition has been a state of the art issue in the advanced PEMFC technology. In this study, non-hydrous protonic conducting material was prepared by the mixing of acidic surfactant of mono-dodecylphosphate (MDP) and organic base of benzimidazole (BnIm). The proton conductivity and thermal stability of MDP-BnIm mixed material increased with the mixing ratio of BnIm. Maximum proton conductivity of MDP-BnIm mixed material (BnIm mixing ratio of 200 wt.%. vs. MDP) was found to be 1×10⁻³ S cm⁻¹ at 150 °C under water-free condition.     

Application of the Solvothermal Process in the Synthesis of High-performance Ag/γ-Al_2O_3 Catalysts

1 INTRODUCTION Since Cu-ZSM-5 was reported as an effective catalyst for the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of excess oxygen, the SCR of NOx has received much attention as a kind of potential technology for cleaning NOx in various oxygen-rich exhausts of diesel engine, lean burning gasoline engine and gas engine. Although a number of catalysts have been tested, to date, it still seems to be difficult to find a catalyst that is completely suit…     

Splash Splat to Disk Splat Transition Behavior in Plasma-Sprayed Metallic Materials

A variety of metallic powder particles were thermally sprayed onto the mirror polished metallic substrate surface and the effect of both substrate temperature and ambient pressure on the flattening behavior of the particle was systematically investigated. In the flattening behavior of the sprayed particle onto the substrate surface, critical conditions were recognized both in the substrate temperature and ambient pressure. That is, the flattening behavior changed transitionally on that critical temperature and pressure range, respectively. A transition temperature, T _t, and transition pressure, P _t, were defined and introduced, respectively for those critical conditions. The fact that the dependence of both transition temperature and transition pressure on the sprayed particle material had similar tendency indicated that the wetting of the substrate by the molten particles seemed to be a domination in the flattening. Three-dimensional transition curvature by combining both transition temperature and transition pressure dependence was proposed as a practical and effective controlling principle of the thermal spray process. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Relaxation approach to topology optimization of frame structure under frequency constraint

This paper deals with the frame topology optimization under the frequency constraint and proposes an algorithm that solves a sequence of relaxation problems to obtain a local optimal solution with high quality. It is known that an optimal solution of this problem often has multiple eigenvalues and the feasible set is disconnected. Due to these two difficulties, conventional nonlinear programming approaches often converge to a local optimal solution that is unacceptable from a practical point of view. In this paper, we formulate the frequency constraint as a positive semidefinite constraint of a certain symmetric matrix, and then relax this constraint to make the feasible set connected. The proposed algorithm solves a sequence of the relaxation problems with gradually decreasing the relaxation parameter. The positive semidefinite constraint is treated with the logarithmic barrier function and, hence, the algorithm finds no difficulty in multiple eigenvalues of a solution. Numerical experiments show that global optimal solutions, or at least local optimal solutions with high qualities, can be obtained with the proposed algorithm.     

Simple method of determining plasma impedance of streamer discharge in atmospheric air

For atmospheric streamer discharges using a lightning impulse generator, we demonstrate a method of determining the plasma impedance in a streamer region by analyzing the periodic attenuated discharge waveforms having high-frequency components. When the streamer region in the plasma can be treated as an equivalent series circuit model including resistance and inductance elements, the regression waveforms obtained by reducing and smoothing the discharge waveforms are analyzed in the equivalent circuit. We found that the streamer resistance increased exponentially with time after the discharge, whereas the streamer inductance and series impedance were constant at 4.0 Ω for longer than the first period of the discharge waveforms. Moreover, the slope of the regression curve increases more rapidly for the positive streamer resistance than for the negative resistance. Finally, the absolute values of the streamer impedance versus time were 3.3-19 Ω and 3.5-9.0 Ω for positive and negative discharges, respectively.     

Design and performance of a punch mechanism based pellet injector for alternative injection in the large helical device

A low speed single barrel pellet injector, using a mechanical punch device has been developed for alternative injection in the large helical device. A pellet is injected by the combined operation of a mechanical punch and a pneumatic propellant system. The pellet shape is cylindrical, 3 mm in diameter and 3 mm in length. Using this technique the speed of the pellet can be controlled flexibly in the range of 100-450 m/s, and a higher speed can be feasible for a higher gas pressure. The injector is equipped with a guide tube selector to direct the pellet to different injection locations. Pellets are exposed to several curved parts with the curvature radii R(c) = 0.8 and 0.3 m when they are transferred in guided tubes to the respective injection locations. Pellet speed variation with pressure at different pellet formation temperatures has been observed. Pellet intactness tests through these guide tubes show a variation in the intact speed limit over a range of pellet formation temperatures from 6.5 to 9.8 K. Pellet speed reduction of less than 6% has been observed after the pellet moves through the curved guide tubes.     

The Visual Computing of Projector‐Camera Systems

This article focuses on real‐time image correction techniques that enable projector‐camera systems to display images onto screens that are not optimized for projections, such as geometrically complex, coloured and textured surfaces. It reviews hardware‐accelerated methods like pixel‐precise geometric warping, radiometric compensation, multi‐focal projection and the correction of general light modulation effects. Online and offline calibration as well as invisible coding methods are explained. Novel attempts in super‐resolution, high‐dynamic range and high‐speed projection are discussed. These techniques open a variety of new applications for projection displays. Some of them will also be presented in this report.