Thermo-acoustic instability in the horizontal Rijke tube

The instability curve of a Rijke tube system was obtained accurately by following different paths of heat power and flow-rate for three regions and by defining its locus from the criterion based on the measured sound pressure levels. The unstable limits in the region of flow-rate lower than that at the minimal power are compared with previous data. To observe the effect of turbulence on the unstable limits, inflow turbulence was introduced by placing a bundle of circular cylinders upstream of the heating part (50< Re_d< 700). The large-amplitude inflow fluctuation may delay the transition of the chamber acoustic mode to the unstable zone even at a sufficient power.     

A 24-GHz 3.9-dB NF low-noise amplifier using 0.18 /spl mu/m CMOS technology

A 24-GHz low-noise amplifier (LNA) was designed and fabricated in a standard 0.18-/spl mu/m CMOS technology. The LNA chip achieves a peak gain of 13.1 dB at 24 GHz and a minimum noise figure of 3.9 dB at 24.3 GHz. The supply voltage and supply current are 1 V and 14 mA, respectively. To the author's knowledge, this LNA demonstrates the lowest noise figure among the reported LNAs in standard CMOS processes above 20 GHz.     

Influence of the silicon surface treatment by plasma etching and scratching on the nucleation of diamond grown in HFCVD - a comparative study

A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with 1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers. Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332 cm⁻¹ and a peak at ∼1,580 cm⁻¹ for both samples.     

Equilibrium and crystallographic measurements of the binary tetrahydrofuran and helium clathrate hydrates

Clathrate compounds are crystalline materials formed by a physical interaction between host and relatively light guest molecules. Various types of nano-sized cages surrounded by host frameworks exist in the highly unique crystalline structures and free guest molecules are entrapped in an open host-guest network. Recently, we reported two peculiar phenomena, swapping and tuning, naturally occurring in the hydrate cages. Helium, one of the smallest light guest molecules, must be the challengeable material in the sense of physics and moreover possesses versatile applications in the field of superconductivity technology and thermonuclear industry. In this regard, we attempted for the first time to synthesize helium hydrates at moderate temperature and pressure conditions. According to inclusion phenomena, helium itself normally cannot form clathrate hydrates due to being too small molecularly without the help of hydrate former molecules (sI, sII, and sH formers). In this study, the hydrate equilibria of the binary clathrate hydrate containing tetrahydrofuran, helium, and water were determined at 2, 3, 5.56 THF mol%. Direct volumetric measurements were also carried out to confirm the exact amount of helium captured in the hydrate cages. Finally, the crystalline structure of the formed mixed hydrates was identified by powder X-ray diffraction, resulting in structure II.     

Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Polysaccharide‐based artificial extracellular matrix: Preparation and characterization of three‐dimensional,macroporous chitosan,and heparin composite scaffold

Scaffold‐guided tissue engineering based on synthetic and natural occurring polymers has gained many interests in recent year. In this study, the development of a chitosan‐heparin artificial extracellular matrix (AECM) is reported. Three‐dimensional, macroporous composite AECMs composed of heparin (Hep) and chitosan (Chito) were prepared by an interpolyelectrolyte complex/lyophilization method. The Chito‐Hep composite AECMs were, respectively, crosslinked with glutaraldehyde, as well as cocrosslinked with N,N‐(3‐dimethylaminopropyl)‐N′‐ethyl carbodiimide (EDC/NHS) and N‐hydroxysuccinimide (NHS). The crosslinking reactions were examined by FT‐IR analysis. In physiological buffer solution (PBS), the EDC/NHS‐crosslinked Chito‐Hep composite AECM showed a relative lower water retention ratio than its glutaraldehyde‐crosslinked counterparts. The EDC/NHS‐crosslinked Chito‐Hep composite AECMs showed excellent biocompatibility, according to the results of the in vitro cytotoxic test. This result suggested that the EDC/NHS‐crosslinked Chito‐Hep composite AECMs might be a potential biomaterial for scaffold‐guided tissue engineering applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

安积伸：从设计“协奏”到设计“独奏”

从安积伸（Shin Azumi）第一次到英国算起，他和英国、和伦敦已经有了近15年的情结。安积伸早已成了各类媒体报道和机构介绍里频繁出现的名字，就连英国设计节的创始人之一约翰·索瑞（John Sorrell）在《Creative Island（创意之岛）》一书中也将其作为对英国创意产业有所影响的驻岛设计师予以了收录。安积伸目前依然在伦敦经营着自己“astudio”．一个从事产品、家具和空间设计的工作室。[第一段]     

Manufacturing and structural safety evaluation of a composite train carbody

This paper explains the manufacturing process of a composite train carbody with a sandwich composite structure for bodyshell and a stainless steel structure for the under frame. In addition, the structural behavior and safety of the composite carbody of the Korean tilting train was investigated by the static load tests. From the test results, the stiffness of the composite carbody met the specified design. In the aspect of strength, the maximum stress of the composite bodyshell was of 12.2% of strength of CF1263 carbon/epoxy.