Geopolymer assembly by emulsion templating: Emulsion stability and hardening mechanisms

This work investigates emulsion templating to synthesize hexadecane oil/geopolymer composites. In a system with hexadecane as the internal (dispersed) phase and an alkali activated continuous phase without added surfactant, adding aluminosilicate clay particles does not increase resistance against creaming or coalescence, while adding a surfactant (L35 or CTAB) stabilizes the solid-liquid interface. Infrared studies and rheological studies of the associated geopolymerization determined that the presence of the organic phase or surfactant has no significant effect on the geopolymerization kinetics, as determined by the change in time of the Si-O-T IR stretching frequency and the rheological moduli involved during the process. The stabilization of the organic template is reminiscent of Pickering emulsion even though we employ a much greater amount of inorganic material for geopolymer formation. Although the addition of surfactant has a significant effect on the behavior of the paste, the percolation of the network remains unmodified, highlighting the fact that the phenomenon is not dependent on viscosity. Finally, rheological measurements were used to obtain the mass fractal dimension of the as-made gel network, which is able to differentiate the interfacial effect between surfactant molecules with a slightly denser interphase when a cationic surfactant is used.     

Preparation of nanocrystalline nickel oxide from nickel hydroxide using spark plasma sintering and inverse Hall-Petch related densification

Nanocrystalline nickel oxide (NiO) was prepared from nickel hydroxide by Spark plasma sintering (SPS) and the mechanisms involved in the densification of NiO were studied. Reverse precipitated nickel hydroxide powders were SPS processed at 400, 600 and 700?°C with 70?MPa pressure. Pure NiO with 12?nm crystallite size formed after 400?°C sintering process. However NiO grains had grown to 18 and 38?nm after 600 and 700?°C sintering respectively. NiO pellets prepared using 600 and 700?°C SPS sintering schedules had relative densities of 83% and 94% respectively. Two displacement rate regimes were observed during densification of NiO in both 600 and 700?°C sintering processes. Decomposition of nickel hydroxide and particle sliding of NiO led to first displacement rate maximum while inverse Hall-Petch based plastic deformation facilitated densification during the constant second displacement rate regime. No densification occurred during sintering holding times indicating the limited role that diffusion played during densification.     

CuInS2/SiNWs/Si composite material for application as potential photoelectrode for photoelectrochemical hydrogen generation

This work aims at developing a new composite material based on nanosized semiconducting CuInS₂ (CIS) particles combined with silicon nanowires grown on a silicon substrate (SiNWs/Si) for photoelectrochemical (PEC)-splitting of water. The CIS particles were prepared via a colloidal method using N-methylimidazole (NMI) as the solvent and an annealing treatment. The SiNWs were obtained by chemical etching of silicon (100) substrates assisted by a metal. The CIS/SiNWs/Si composite material was obtained by deposition of an aliquot of a suspension of CIS particles onto the SiNWs/Si substrate, using spin coating followed by a drying step. The XRD pattern demonstrated that CuInS₂ grows in the tetragonal/chalcopyrite phase, while SiNWs/Si presents a cubic structure. The SEM images show semi-spherical particles (～10 nm) distributed on the surface of silicon nanowires (～10 μm). The EIS measurements reveal n-type conductivity for CIS, SiNWs/Si and CIS/SiNWs/Si materials, which could favour the oxidation reaction of water molecules.     

Migration of Point Defects in the Field of a Temperature Gradient

The influence of the temperature gradient over the thickness of the cladding of a fuel element of a fast-neutron reactor on the migration of point defects formed in the cladding material due to neutron irradiation has been studied. It has been shown that, under the action of the temperature gradient, the flux of vacancies onto the inner surface of the cladding is higher than the flux of interstitial atoms, which leads to the formation of a specific concentration profile in the cladding with a vacancy-depleted zone near the inner surface. The experimental results on the spatial distribution of pores over the cladding thickness have been presented with which the data on the concentration profiles and vacancy fluxes have been compared.     

A Giant Frequency Shift in the Raman Spectrum of Water Adsorbed on a Metallic Silver Surface

The Raman spectrum of water adsorbed on a metallic silver surface reveals an anomalously large shift of the vibrational frequency as compared to that in the bulk. The results are compared to data reported by other researchers, and possible interpretations of the observed phenomenon are discussed.     

Strain Concentration Effect in Cu–Al–Ni Single Crystals under a Longitudinal Bending Force

The behavior of a superelastic Cu?14.2% Al?4%Ni single crystal in the case of high reversible strains under a longitudinal bending force was investigated. The effect of strain confinement along the crystal length was revealed and studied. The highest reversible strains (up to 10%) were shown to be confined within the central part of the bent crystal.     

Technical and economic analysis of solvent-based lithium-ion electrode drying with water and NMP

Processing lithium-ion battery (LIB) electrode dispersions with water as the solvent during primary drying offers many advantages over N-methylpyrrolidone (NMP). An in-depth analysis of the comparative drying costs of LIB electrodes is discussed for both NMP- and water-based dispersion processing in terms of battery pack $/kWh. Electrode coating manufacturing and capital equipment cost savings are compared for water vs. conventional NMP organic solvent processing. A major finding of this work is that the total electrode manufacturing costs, whether water- or NMP-based, contribute about 8–9% of the total pack cost. However, it was found that up to a 2?×?reduction in electrode processing (drying and solvent recovery) cost can be expected along with a $3–6?M savings in associated plant capital equipment (for a plant producing 100,000 10-kWh Plug-in Hybrid Electric Vehicle (PHEV) batteries) using water as the electrode solvent. This paper shows a different perspective in that the most important benefits of aqueous electrode processing actually revolve around capital equipment savings and environmental stewardship and not processing cost savings.     

Role of Elastic Interphase Deformations in the Formation of Crystal Structure of β-Nb Particles Precipitating in a Zr–2.5% Nb Alloy

X-ray diffraction analysis has been used to study the structure of the α-Zr matrix phase and the precipitation of β-Nb particles upon the annealing of a Zr–2.5% Nb deformed alloy. It has been found that the process of the precipitation of the strengthening β-Nb particles in the alloy is accompanied by the appearance of fields of elastic interphase deformations in the matrix α phase of the alloy due to the difference in the specific atomic volumes of the crystal structures of the matrix and precipitated phases. It has been shown experimentally that, as a result of the presence of interphase deformations in the alloy, the bcc crystal structure of the precipitating β-Nb particles undergoes monoclinic distortions.