Simplified method for the measurement of segmental colonic transit time

Segmental colonic transit has been measured in 101 patients. Two MBq of 111Indium absorbed on resin pellets and encapsulated in an enteric coated capsule was given at 7 00 am. Hourly images during the first day, and three images during each subsequent day were acquired for up to three days. Using all scan and patient data the scans were categorised in one of the five patterns of colonic transit: normal, rapid, right delay, left delay, or generalised delay. The geometric centres and per cent activity at each time point was compared between the five groups of colonic transit patients to find the best time for imaging and so to distinguish the five groups. During the first day, early images did not help in diagnosis of patterns of transit, however, in the later images (six hours onwards after the ingestion of the activity) the rapid transit groups could be identified. Images at 27 and 51 hours were both required to distinguish all five groups of patients from each other. Only in the 'normal' transit patients was there some excretion of the activity during the course of the second day, otherwise there was no difference in the images taken in the course of a day (second or third day). A simplified protocol requires a minimum of three images to distinguish all five patterns of colonic transit. The activity should be ingested in the morning (7 00 am) and the first image taken at the end of the working day (8-10 hours after ingestion), the second image on the morning of the second day, and the third image during the course of the third day. This simple protocol would provide all the clinically relevant information necessary for correct classification of the colonic transit.     

Measurement of specimen charging in scanning electron microscopy with a kelvin probe

A vibrating Kelvin probe in form of a platinum wire loop is used to measure the surface potential U_s on electron-irradiated free-floating metal and insulator specimens as a function of electron energy E. This allows an accurate measurement of the critical electron energy E₂ for no charging. At energies below E₂, the positive charging increases with decreasing energy to U_s=2–5 eV at E=0.5 keV and switching off the collector bias of the Everhart-Thornley detector. A two-to threefold increase of U_s is observed when the bias is switched on. For E > E₂, the strong increase of a negative surface potential can be measured. Insulating films free-supported on a conductive substrate show a steep decrease to small positive and negative U_s when the film thickness becomes lower than the electron range at a critical energy E₃ > E₂. At insulating specimen the temporal decrease of charging can be measured when the electron beam is switched off.     

Pain threshold in man

The design and application of an apparatus for measuring pain threshold by controlling the conditions of an experiment carefully and measuring stimulus and response parameters precisely are described. Heat generated by an incandescent source, focused on a small area of the subject's forehead, was used as the stimulus to determine the cutaneous pain threshold. The equipment was in different experiments in which the threshold of thermocutaneous pain was evaluated with and without the use of an analgesic. The analgesic Pirazolane was found to reduce thermocutaneous pain threshold and to diminish the average duration of alpha rhythm blockade and the response of galvanic skin resistance. The results of these experiments with constituents of marijuana indicated that canabidiol provokes and increases the sensibility of pain reactions while both Δ9 THC and canabinol do not modify the pain threshold     

A neural network model for fault detection in conjunction with a programmable logic controller

This paper discusses the feasibility of using neural networks as a tool in the fault detection process. A neural network is integrated with a state language programmable logic controller, an important device in an automatic control system. Time series data related to time spent in a state is gathered and used as input into a neural network, for the purpose of identifying when a fault has occurred. A feedforward neural network is used to identify which (if any) of three types of faults may have occurred. Experimental results related to sensitivity and accuracy measures are presented. A brief review of related applications and research is also presented.     

Comparing the motivations of Spanish and Finnish computer personnel with those of the United States

A survey of perceptions of IS personnel – managers, technical specialists and programmer/analysts – was conducted by the Association for Technical Information in Spain, using the JDS/DP, a modification of the job diagnostic survey instrument. Data were collected on fifteen job variables, related to four motivation aspects: job components, satisfaction levels, need for growth/achievement and goal participation/feedback. The results were compared with those of a similar survey for the same job types in Finland. Results were also compared with the norms developed for computer personnel in the USA. The survey revealed that personnel attracted to the computer field have a high need for growth and a low need for social interaction. It also revealed that the work itself was ranked highest among eleven motivating factors. For both Spain and Finland, the technical specialist job had a mis-match between the job's motivating potential and the employee's need for growth, compared with similar personnel in the USA. By examining the core job dimensions, managers can redesign the job to produce a match between these two major components of motivation.